iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 15875:2012/AC:2013

(Corrigendum)

Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste

Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste

This European standard specifies methods to determine the potential of sulfide bearing materials for the formation of acidic drainage. Specified are methods for determining both the acid potential (AP) and the neutralisation potential (NP) of the material. From these results the net neutralisation potential (NNP) and the neutralisation potential ratio (NPR) are calculated. This European standard is applicable to all sulfide bearing wastes from the extractive industries excluding wastes which will have pH < 2 in the initial step of the procedure described in 8.2.3.

Charakterisierung von Abfällen - Statische Prüfung zur Bestimmung des Säurebildungspotenzials und des Neutralisationspotenzials von sulfidhaltigen Abfällen

Caractérisation des déchets - Essai statique pour la détermination du potentiel de génération d'acide et du potentiel de neutralisation des déchets sulfurés

Karakterizacija odpadkov - Statični preskus za določevanje kislinske in nevtralizacijske kapacitete odpadkov, ki vsebujejo sulfid - Popravek AC

Ta evropski standard določa metode za določevanje kapacitete materialov, ki vsebujejo sulfid, za tvorbo kisle drenaže. Opredeljene so metode za določevanje kislinske (AP) in nevtralizacijske kapacitete (NP) materiala. Iz teh rezultatov se računa neto nevtralizacijska kapaciteta (NNP) in razmerje nevtralizacijske kapacitete (NPR). Ta evropski standard se uporablja za vse odpadke ekstraktivne industrije, ki vsebujejo sulfid, razen odpadkov, katerih pH v prvi fazi postopka, opisanega v 8.2.3, znaša < 2.

General Information

Status
Published
Publication Date
23-Dec-2012
ICS
13.030.10 - Solid wastes
Technical Committee
KAT - Soil quality
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
26-Oct-2012
Due Date
31-Dec-2012
Completion Date
24-Dec-2012
Directive
2006/21/EC - Management of waste from extractive industries
Mandate
M/395 - Mandate to CEN for the development of standardised methods relating to the characterisation of wastes from the extractive industries
Ref Project
EN 15875:2011/AC:2012 - Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste

Relations

Corrects
SIST EN 15875:2012 - Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste
Effective Date
01-Jan-2013

Buy Standard

EN 15875:2012/AC:2013EN 15875:2012/AC:2013
PreviousNext
Corrigendum
EN 15875:2012/AC:2013
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Charakterisierung von Abfällen - Statische Prüfung zur Bestimmung des Säurebildungspotenzials und des Neutralisationspotenzials von sulfidhaltigen AbfällenCaractérisation des déchets - Essai statique pour la détermination du potentiel de génération d'acide et du potentiel de neutralisation des déchets sulfurésCharacterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste13.030.10Trdni odpadkiSolid wastesICS:Ta slovenski standard je istoveten z:EN 15875:2011/AC:2012SIST EN 15875:2012/AC:2013en,fr,de01-januar-2013SIST EN 15875:2012/AC:2013SLOVENSKI
STANDARD



SIST EN 15875:2012/AC:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15875:2011/AC
August 2012
Août 2012
August 2012 ICS 13.030.10 English version Version Française Deutsche Fassung
Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste
Caractérisation des déchets - Essai statique pour la détermination du potentiel de génération d'acide et du potentiel de neutralisation des déchets sulfurés
Charakterisierung von Abfällen - Statische Prüfung
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 17322:2020(Main)
Environmental Solid Matrices - Determination of polychlorinated biphenyls (PCB) by gas chromatography - mass selective detection (GC-MS) or electron-capture detection (GC-ECD)
EN 17322:2020

This European Standard specifies a method for quantitative determination of seven selected polychlorinated biphenyls (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153 and PCB180) in soil, sludge, sediment, treated biowaste and waste and using GC-MS and GC-ECD.
The limit of detection depends on the determinants, the equipment used, the quality of chemicals used for the extraction of the sample and the clean-up of the extract.
Under the conditions specified in this European Standard, lower limit of application from 1 μg/kg (expressed as dry matter) for soils, sludge and biowaste to 10 μg/kg (expressed as dry matter) for solid waste can be achieved. For some specific samples the limit of 10 μg/kg cannot be reached.
Sludge, waste and treated biowaste may differ in properties, as well as in the expected contamination levels of PCBs and presence of interfering substances. These differences make it impossible to describe one general procedure. This European Standard contains decision tables based on the properties of the sample and the extraction and clean-up procedure to be used.
NOTE   For the analysis of PCB in insulating liquids, petroleum products, used oils and aqueous samples is referred to EN 61619, EN 12766–1 and EN ISO 6468 respectively.
The method may be applied to the analysis of other PCB congeners not specified in the scope, provided suitability is proven by proper in-house validation experiments

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 16675:2018(Main)
Waste - Test methods for the determination of the monolithic status of waste to be landfilled
CEN/TS 16675:2018

This Technical Specification provides methods, which can be used to assess the monolithic character of a stabilised/solidified waste, with respect to landfilling. Information on the monolithic character is required to enable the choice of appropriate leaching tests for determination of the release of different substances from stabilised/solidified waste under specified (landfilling) conditions.
This document includes several physical and/or chemical test methods each addressing different aspects of monolithic character. The selection of methods required for an assessment of the monolithic character of a stabilised/solidified waste may vary, depending on the scenario to be addressed or it may be specified in regulation.
Rather than describing the procedures and methods in detail this document refers to existing standards and provides some guidance on their use on stabilised/solidified waste materials.
This Technical Specification does not address issues related to health and safety.
The following procedures and methods are included in this document:
-   test to determine unconfined compressive strength;
-   test to determine permeability;
-   test to determine the loss of mass by dissolution;
-   test to determine expansion;
-   test to determine the content of organic matter;
-   test to determine freeze/thaw effects.

  • Technical specification
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15863:2015(Main)
Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions
EN 15863:2015

This European Standard is applicable for determining the leaching behaviour of monolithic wastes under dynamic conditions. The test is performed under fixed experimental conditions in this document. This test is aimed at determining the release as a function of time of inorganic constituents from a monolithic waste, when it is put into contact with an aqueous solution (leachant).
This dynamic monolithic leaching test (DMLT) is a parameter specific test as specified in EN 12920 and is therefore not aimed at simulating real situations. The application of this test method alone is not sufficient for the determination of the detailed leaching behaviour of a monolithic waste under specified conditions.
In the framework of EN 12920 and in combination with additional chemical information, the test results are used to identify the leaching mechanisms and their relative importance. The intrinsic properties can be used to predict the release of constituents at a given time frame, in order to assess the leaching behaviour of monolithic waste materials, placed in different situations or scenarios (including disposal and recycling scenarios).
The test method applies to regularly shaped test portions of monolithic wastes with minimum dimensions of 40 mm in all directions, that are assumed to maintain their integrity over a time frame relevant for the considered scenario. The test method applies to test portions for which the geometric surface area can be determined with the help of simple geometric equations. The test method applies to low permeable monolithic materials.
NOTE 1   If, in order to comply with the requirements of regular shape, the test portion is prepared by cutting or coring, then new surfaces are exposed which can lead to change(s) in leaching properties. On the other hand if the test portion is prepared by moulding, the surface will be dependent to the type of mould and the conditions of storage. If the intention is to evaluate the behaviour of the material core, the specimen needs to be stored without any contact with air to avoid carbonation.
NOTE 2   For monolithic waste materials with a saturated hydraulic conductivity higher than 10-8 m/s water is likely to percolate through the monolith rather than flow around. In such cases relating the release to the geometric surface can lead to misinterpretation. A percolation test is then more appropriate (e.g. EN 14405).
This procedure may not be applicable to materials reacting with the leachant, leading for example to excessive gas emission or an excessive heat release.
This document has been developed to determine the release of mainly inorganic constituents from wastes. It does not take into account the particular characteristics of organic constituents, nor the consequences of microbiological processes in organic degradable wastes.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16377:2014(Main)
Characterization of waste - Determination of brominated flame retardants (BFR) in solid waste
EN 16377:2013

This European Standard specifies a method for the determination of selected polybrominated flame retardants (BFR), chemically known as polybrominated diphenylethers (BDE), in waste materials using gas chromatography/mass spectrometry (GC-MS) in the electron impact (EI) ionisation mode (GC-EI-MS). When applying GC-EI-MS, the method is applicable to samples containing 100 μg/kg to 5 000 μg/kg of tetra- to octabromodiphenylether congeners and 100 μg/kg to 10 000 μg/kg of decabromo diphenylether (see Table 1). It is also possible to analyse other brominated flame retardants applying the method described in this European Standard, provided the method's applicability has been proven.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 16365:2013(Main)
Characterization of waste - Sampling of waste from extractive industries
CEN/TR 16365:2012

This Technical Report gives additional and specific information on sampling for testing of waste from the extractive industry to support the development of appropriate sampling plans. This supplementary guidance to EN 14899 is required because waste from the extractive industry differs considerably from the waste types and sampling scenarios covered in the existing technical reports (CEN/TR 15310-1 to -5) that support the Framework Standard. This guidance document should be used in conjunction with EN 14899 and its supporting technical reports CEN/TR 15310-1 to -5. The approach to sampling described in this document is primarily focused on the requirements to undertake mineralogical and geochemical testing of the waste. Whilst much of the background information provided is also relevant to geotechnical investigations there may be important additional requirements or differences in approach for determining relevant physical parameters. For example, many geotechnical parameters are determined using field tests, which are not discussed in this document. References to alternative source documentation are provided. The guidance provided in this document applies only to above-ground exposure to radio-nuclides present in the undisturbed earth crust and not to the production, processing, handling use, holding, storage, transport, or disposal of radioactive substances that are or have been processed for their radioactive, fissile or fertile properties. This Technical Report provides some discussion of current best practice, but is not exhaustive. To clarify the text, the document provides a number of worked examples in the Annexes.

  • Technical report
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 15862:2013(Main)
Characterization of waste - Compliance leaching test - One stage batch leaching test for monoliths at fixed liquid to surface area ratio (L/A) for test portions with fixed minimum dimensions
CEN/TS 15862:2012

This Technical Specification specifies a compliance test for routine testing providing information on the leaching of monolithic waste which can be obtained under the experimental conditions specified hereafter with a single batch leaching test at a specified liquid to surface area ratio (L/A) of 12 (cm3*cm-2). It applies to test portion of monolithic waste of regular shape, with a minimum dimension of 40 mm in all directions, obtained e.g. by cutting, coring or moulding. This document is not applicable if the surface area of the test portion cannot be determined by simple geometrical means. This document has been developed to determine the release of mainly inorganic constituents from wastes. It does not take into account the particular characteristics of organic constituents nor the consequences of microbiological processes in organic degradable wastes. The test procedure specified in this document produces an eluate which subsequently need to be characterized physically and chemically, according to appropriate standard methods. NOTE 1 If, in order to comply with the requirement of regular shape, the test portion is prepared by cutting or coring, then new surfaces are exposed which can lead to change(s) in leaching properties. NOTE 2 This procedure may not be applicable to materials reacting with the leachant, leading for example to excessive gas emission or an excessive heat release. This leaching test does not provide information by itself on dynamic leaching behaviour, as specified in EN 12920. It does not give information on equilibrium conditions. For specific situations or basic characterization, other tests are available in the toolbox of CEN/TC 292 "Characterization of waste". This document does not address issues related to health and safety.

  • Technical specification
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15875:2012(Main)
Characterization of waste - Static test for determination of acid potential and neutralisation potential of sulfidic waste
EN 15875:2011

This European standard specifies methods to determine the potential of sulfide bearing materials for the formation of acidic drainage. Specified are methods for determining both the acid potential (AP) and the neutralisation potential (NP) of the material. From these results the net neutralisation potential (NNP) and the neutralisation potential ratio (NPR) are calculated. This European standard is applicable to all sulfide bearing wastes from the extractive industries excluding wastes which will have pH < 2 in the initial step of the procedure described in 8.2.3.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 16130:2011(Main)
Characterization of waste - On-site verification
CEN/TR 16130:2011

This Technical Report gives guidance on the strategy for on-site verification and quality control of waste at landfills. It describes methods of visual inspection, control of documents and choice of necessity of testing by either screening methods or reference methods. It gives guidance on sampling, sample preparation and extraction for analysis.
The same procedures may be useful for on-site verification and quality control of waste at treatment plants.

  • Technical report
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15309:2007
Characterization of waste and soil - Determination of elemental composition by X-ray fluorescence
EN 15309:2007

This European Standard specifies the procedure for a quantitative determination of major and trace element concentrations in homogeneous solid waste, soil and soil-like material by energy dispersive X-ray fluorescence (EDXRF) spectrometry or wavelength dispersive X-ray fluorescence (WDXRF) spectrometry using a calibration with matrix-matched standards.
This European Standard is applicable for the following elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Br, Rb, Sr, Y, Zr, Nb, Mo, Ag, Cd, Sn, Sb, Te, I, Cs, Ba, Ta, W, Hg, Tl, Pb, Bi, Th and U. Concentration levels between approximately 0,000 1 % and 100 % can be determined depending on the element and the instrument used.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 15310-1:2007(Main)
Characterization of waste - Sampling of waste materials - Part 1: Guidance on selection and application of criteria for sampling under various conditions
CEN/TR 15310-1:2006

This Technical Report discusses the statistical principles of sampling, and provides a number of statistical tools to assist in the design of testing programmes for application to sampling under various conditions.
NOTE 1   Given the great variety of waste types, sampling situations and objectives, this Technical Report cannot provide definitive instructions that cover all scenarios. Instead, it discusses the basic statistical approach to be followed, and provides statistical tools that can be applied to determine the amount and type of sampling (e.g. number of samples and sample size) in any given situation to achieve results of adequate reliability (i.e. precision and confidence).
NOTE 2   The document provides considerable detail on current best practice, but is not exhaustive.
NOTE 3   To clarify the text, the document provides a number of worked examples.

  • Technical report
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day