SIST EN ISO 8611-1:2004
(Main)Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO 8611-1:2004)
Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO 8611-1:2004)
ISO 8611-1:2004 specifies test methods of existing and prototype flat pallets for materials handling for all types of use
It cannot be used to evaluate a pallet to normative ISO requirements without the additional application of ISO/TS 8611-2 and ISO/TS 8611-3.
Paletten für den Gütertransport - Flachpaletten - Teil 1: Prüfverfahren (ISO 8611-1:2004)
Palettes pour la manutention - Palettes plates - Partie 1: Méthodes d'essai (ISO 8611-1:2004)
L'ISO 8611-1:2004 spécifie des méthodes d'essai des palettes existantes et des prototypes de palettes plates pour manutention pour tout type d'utilisation.
Elle ne peut pas être utilisée pour évaluer une palette conformément aux exigences normatives de l'ISO sans appliquer également l'ISO/TS 8611-2 et l'ISO/TS 8611-3.
Palete za ravnanje z materiali - Ravne palete – 1. del: Preskusne metode (ISO 8611-1:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8611-1:2004
01-september-2004
Palete za ravnanje z materiali - Ravne palete – 1. del: Preskusne metode (ISO 8611-
1:2004)
Pallets for materials handling - Flat pallets - Part 1: Test methods (ISO 8611-1:2004)
Paletten für den Gütertransport - Flachpaletten - Teil 1: Prüfverfahren (ISO 8611-1:2004)
Palettes pour la manutention - Palettes plates - Partie 1: Méthodes d'essai (ISO 8611-
1:2004)
Ta slovenski standard je istoveten z: EN ISO 8611-1:2004
ICS:
55.180.20 9HþQDPHQVNHSDOHWH General purpose pallets
SIST EN ISO 8611-1:2004 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8611-1:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 8611-1:2004
EUROPEAN STANDARD
EN ISO 8611-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2004
ICS 55.180.20
English version
Pallets for materials handling - Flat pallets - Part 1: Test
methods (ISO 8611-1:2004)
Palettes pour la manutention - Palettes plates - Partie 1: Paletten für den Gütertransport - Flachpaletten - Teil 1:
Méthodes d'essai (ISO 8611-1:2004) Prüfverfahren (ISO 8611-1:2004)
This European Standard was approved by CEN on 9 February 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8611-1:2004 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8611-1:2004
EN ISO 8611-1:2004 (E)
Foreword
This document (EN ISO 8611-1:2004) a été élaboré par le Comité Technique ISO/TC 51
"Plateaux de chargement pour transport et manutention directe de charges unitaires" en
collaboration avec le Comité Technique CEN/TC 261 "Emballage" dont le secrétariat est tenu
par l’AFNOR
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by August 2004, and conflicting national
standards shall be withdrawn at the latest by August 2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 8611-1:2004 has been approved by CEN as EN ISO 8611-1:2004 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8611-1:2004
EN ISO 8611-1:2004 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 445 1996 Pallets for materials handling - EN ISO 445 1998
Vocabulary
ISO 12777-1 1994 Methods of test for pallet joints - EN ISO 12777-1 1996
Part 1: Determination of bending
resistance of pallet nails, other
dowel-type fasteners and staples
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8611-1:2004
---------------------- Page: 6 ----------------------
SIST EN ISO 8611-1:2004
INTERNATIONAL ISO
STANDARD 8611-1
First edition
2004-02-15
Pallets for materials handling — Flat
pallets —
Part 1:
Test methods
Palettes pour la manutention — Palettes plates —
Partie 1: Méthodes d'essai
Reference number
ISO 8611-1:2004(E)
©
ISO 2004
---------------------- Page: 7 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Measurements . 2
5 Accuracy of tests and apparatus . 2
6 Test load. 3
7 List of tests . 3
8 Static tests . 4
8.1 Test No. 1 — Bending tests. 4
8.2 Test No. 2 — Wing pallet bending tests. 5
8.3 Test No. 3 — Air bag bending tests . 7
8.4 Test No. 4 — Fork lifting tests . 10
8.5 Test No. 5 — Compression tests for blocks or stringers . 11
8.6 Test No. 6 — Stacking test. 13
8.7 Test No. 7 — Dead-weight bending test .14
8.8 Test No. 8 — Bottom deck bending tests . 15
8.9 Test No. 9 — Static shear test. 16
9 Dynamic strength tests . 17
9.1 Test No. 10 — Corner drop test . 17
9.2 Inclined plane impact tests . 18
10 Friction tests. 23
10.1 Test No. 14 — Static coefficient of friction test .23
10.2 Test No. 15 — Slip angle test. 24
11 Test report. 25
11.1 General information — all materials . 25
11.2 Information for wooden and wood-based composite pallets. 26
11.3 Information for plastic pallets. 26
11.4 Information for pallets made of other materials . 26
Bibliography . 27
© ISO 2004 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8611-1 was prepared by Technical Committee ISO/TC 51, Pallets for unit load method of materials
handling.
This first edition, together with ISO 8611-2 and ISO 8611-3, cancels and replaces ISO 8611:1991.
ISO 8611 consists of the following parts, under the general title Pallets for materials handling — Flat pallets:
Part 1: Test methods
Part 2: Performance requirements and selection of tests (Technical Specification)
Part 3: Maximum working load (Technical Specification)
iv © ISO 2004 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
Introduction
The 1991 edition of ISO 8611 described a system of sequential testing that relied upon a pallet passing every
test in a series. This meant that one pallet could be near to failure in one particular test where another pallet
might be substantially over-designed. Using the (earlier) deflection criteria, both pallets were presented as
equals in terms of safety factor. The notched stringer pallet was a good example of this where it was typically
very stiff, but frequently near fracture point in the (old) bending test. The new, three-part version of ISO 8611
redresses this in failing every specimen in order to establish a definite safety factor. Stiffness is dealt with as a
separate series of measurements conducted during testing.
Conducting the tests requires experience in testing (including the load) and also some expertise of the
materials under test. This part of ISO 8611, in conjunction with ISO/TS 8611-2 and ISO/TS 8611-3, has been
expressly designed to cover all pallet materials either when used alone or used as composites. A further
change over ISO 8611:1991 is that all pallets for materials handling are now covered and not just high quality
through-transit, exchange or pool pallets.
This part of ISO 8611 cannot be used to evaluate a pallet to normative ISO requirements without the
additional application of ISO/TS 8611-2 and ISO/TS 8611-3.
This part of ISO 8611 was designed to be coupled with ISO/TR 10232:1989 General-purpose flat pallets for
through transit of goods — Design rating and maximum working load and ISO/TR 10233:1989 General-
purpose flat pallets for through transit of goods — Performance requirements.
The changing of the title and the scope of ISO 6780 from General purpose flat pallets for through transit of
goods — Principal dimensions and tolerances, to a wider scope of Flat pallets for intercontinental materials
handling — Principal dimensions and tolerances, makes it necessary to amend ISO 8611:1991 and the
Technical Reports ISO/TR 10232 and ISO/TR 10233. The test methods, performance requirements and
design rating and maximum working load should now include not only “general purpose pallets” but also all
other pallets for materials handling.
© ISO 2004 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 8611-1:2004
---------------------- Page: 12 ----------------------
SIST EN ISO 8611-1:2004
INTERNATIONAL STANDARD ISO 8611-1:2004(E)
Pallets for materials handling — Flat pallets —
Part 1:
Test methods
1 Scope
This part of ISO 8611 specifies test methods of existing and prototype flat pallets for materials handling (for all
types of use).
NOTE Specific tests for determining load capacity do not replace the value of conducting field tests on specific pallet
designs.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 445, Pallets for materials handling — Vocabulary
ISO 2244, Packaging — Complete, filled transport packages and unit loads — Horizontal impact tests
1)
ISO/TS 8611-2:— , Pallets for materials handling — Flat pallets — Part 2: Performance requirements and
selection of tests
ISO 12777-1, Methods of test for pallet joints — Part 1: Determination of bending resistance of pallet nails,
other dowel-type fasteners and staples
EN 13183-2, Moisture content of a piece of sawn timber — Part 2: Estimation by electrical resistance method
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 445 (some of which are repeated
below for convenience) and the following apply.
3.1
test load
load applicators, the load board or load box and the applied load itself
1) To be published.
© ISO 2004 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
3.2
ultimate load
load at which compression, displacement or deflection is no longer contained, resulting in the destruction of
the specimen or breaking of one component, or when displacement, deformation or deflection becomes
excessive
NOTE See Table 1 of ISO/TS 8611-2:—.
3.3
stiffness
relative deformation of a pallet or component under load
NOTE High stiffness means small displacement, deflection or deformation, for a given load.
3.4
racking
storage of loaded pallets in drive-in or beam racks
3.5
stacking
placing of pallets with unit loads one upon the other without recourse to intermediate shelves or racking
3.6
payload
load carried by the pallet in use
4 Measurements
4.1 Pallets selected for testing shall be checked to ensure that materials, construction and dimensions
conform to any associated written specification.
4.2 The mass and the material of each pallet shall be determined and recorded at the time of testing.
4.3 The moisture content of wooden pallets shall be measured and recorded in accordance with
EN 13183-2 at the time of testing.
NOTE Clause 11 gives further details on what should be recorded during testing and in the written report.
5 Accuracy of tests and apparatus
5.1 Test apparatus shall satisfy the following requirements:
a) in the design of the test equipment, the tolerances on all dimensions shall be ± 2 %;
b) the accuracy of measuring equipment for tests shall be ± 0,5 mm;
c) the accuracy of positioning of every component, excluding the test load, shall be ± 2 mm, measurement
gauges shall be positioned to ± 4 mm;
d) the accuracy of positioning of the centre of application of test load (where used) shall be ± 10 mm;
e) the total mass of the test load applied shall be within ± 3 % of the prescribed value.
5.2 No part of any test rig shall distort an amount greater than 3 mm when under maximum test load.
Distortion of the test rig shall be taken into account in measuring deflections of the pallet.
NOTE Using heavy duty steel box sections in the construction of fixtures in tests 1 and 2 (see Table 1) will normally
result in central distortions approaching the 3 mm given limit.
5.3 The inclined plane apparatus shall be constructed as specified in ISO 2244 and shall permit inclined
travel distance to change by 250 mm increments from 250 mm to 1 250 mm, each increment to within ± 5 mm.
2 © ISO 2004 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
6 Test load
A general value for the test load is not fixed. The test load for each test is defined in ISO/TS 8611-2.
The test load shall be applied with hydraulic or air pressure or with dead load and shall increase continuously
or in steps to the failure (for determination of ultimate load) or up to the fixed value (for qualification tests).
7 List of tests
The matrix of tests applicable to this document are as shown in Table 1.
For tests numbered 1, 2, 3, 4, 5 and 8, two tests (a and b) are necessary, which can be carried out in one test
sample (first b and then a) or in two separate test samples. For tests numbered 1, 2, 3, 4, 5 and 8, testing
shall always be conducted with new untested pallets.
Table 1 — List of tests
Test Handling activity or
Test No. Characteristic Ref. No.
Measurement purpose of the test
Static tests 8
1 Bending tests 8.1
Pallet length, width Racking
1a Bending strength 8.1.3.1
1b Bending stiffness 8.1.3.2
2 Wing pallet bending tests 8.2
Pallet length, width Lifting with slings
2a Bending strength 8.2.3.1
2b Bending stiffness 8.2.3.2
3 Air bag bending tests 8.3
3a Bending strength Pallet length, width Racking 8.3.3.1
3b Bending stiffness 8.3.3.2
4 Fork lifting tests 8.4
Lifting with forklift and pallet
4a Bending strength Top deck 8.4.3.1
trucks
4b Bending stiffness 8.4.3.2
5 Compression tests for 8.5
blocks or stringers
Height of blocks, Any activity that compress
5a Blocks or stringers strength stringers blocks or stringers 8.5.3.1
5b Blocks or stringers stiffness 8.5.3.2
6 Stacking test Top and bottom deck Stacking 8.6
7 Dead-weight bending test Pallet length, width Racking 8.7
8 Bottom deck bending tests 8.8
Racking/stacking/
Bottom deck
8a Bending strength 8.8.3.1
conveyors
8b Bending stiffness 8.8.3.2
9 Static shear test Decks, blocks, stringer Distortion resistance 8.9
Dynamic strength tests 9
10 Corner drop test Diagonal rigidity Resistance to impacts 9.1
11 Shear impact test Decks, blocks, stringer Distortion resistance 9.2.2
12 Top deck edge impact test Top leading deckboard Resistance to fork arms 9.2.3
13 Block impact test Corner block, stringer Resistance to fork tip 9.2.4
Friction tests 10
14 Static coefficient of Under deck/fork arms Slip resistance on fork
10.1
friction test arms
15 Slip angle test Top deck/payload Slip resistance of loads 10.2
© ISO 2004 – All rights reserved 3
---------------------- Page: 15 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
8 Static tests
8.1 Test No. 1 — Bending tests
8.1.1 Purpose
The purpose of these tests is to determine the bending strength (Test 1a) and bending stiffness (Test 1b) of
the pallet in racking situations.
8.1.2 Procedure
8.1.2.1 In order to establish the weakest pallet support dimension, test one pallet across the length of the
pallet and then a second pallet across the width of the pallet. There is no requirement for further tests on the
stronger dimension unless the result was within 15 % of the weaker.
8.1.2.2 This having been established, place a fresh pallet across its weakest side, top deck uppermost,
on pallet supports positioned with their centrelines 75 mm from the outer edges of the pallet. The load
applicators shall be positioned at 0,25 L or 0,25 L , when measured as shown, where L or L is the distance
1 2 1 2
between the centre lines of the pallet supports (see Figure 1).
8.1.2.3 Load applicators and supports shall be flush with or project beyond the edges of the pallet. Edges
shall be relieved with 2 mm ± 1 mm radii. Where load applicators coincide with gaps between deckboards,
in-fill pieces of equal thickness to deckboards with 3 mm to 6 mm overall clearance on each shall be used.
Place on the pallet deck the load applicators and the load board, then apply the rest of the test load.
Dimensions in millimetres
Key
1 test load 3 load applicator 5 safety stop
2 load board 4 support 6 lip
Figure 1 — Bending test
4 © ISO 2004 – All rights reserved
---------------------- Page: 16 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
8.1.3 Measurements
8.1.3.1 Test No. 1a — Determination of bending strength
Place a load on the load board until breakage of one of the components of the pallet or until reaching an
excessive deflection or deformation. Record the ultimate load.
8.1.3.2 Test No. 1b — Determination of bending stiffness
Depending on the support location, the deflection, y, shall be measured at points A [maximum of y at A (B )
1 1
and A (B )]:
2 2
a) on the unloaded pallet;
b) after positioning of the load applicators and the load board;
c) immediately after full test load is applied;
d) at end of the full test load period;
e) after the relaxation period.
8.2 Test No. 2 — Wing pallet bending tests
8.2.1 Purpose
The purpose of these tests is to determine the bending strength (Test 2a) and the bending stiffness (Test 2b)
of winged pallet during lifting with slings
8.2.2 Procedure
Place the wing pallet, top deck uppermost, on four posts 50 mm × 50 mm positioned beneath the wings of the
top deck flush with the ends of the pallet and 15 mm from the side of the block or the stringer. The supports
shall be fixed at such a height that a space of at least 50 mm is between the underside of the bottom deck and
the ground or test frame. Each load applicator shall be positioned such that the dimension from the inside
edge of the support to the centre line of the load applicators shall be 0,25 L as shown in Figure 2. Place the
1
load board on the load applicators and then apply the rest of the test load.
© ISO 2004 – All rights reserved 5
---------------------- Page: 17 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
Dimensions in millimetres
Key
1 test load
2 load board
3 safety stop
4 load applicator
5 support
Figure 2 — Wing pallet bending test
8.2.3 Measurements
8.2.3.1 Test No. 2a — Determination of bending strength
Place a load on the load board until breakage of one of the components of the pallet or until reaching an
excessive deflection or deformation. Record the ultimate load.
8.2.3.2 Test No. 2b — Determination of bending stiffness
Depending on the support location, the deflection, y, shall be measured at points A [average of y at A (B )
1 1
and A (B )]:
2 2
a) on the unloaded pallet;
b) after positioning of the load applicators and the load board;
c) immediately after the full test load is applied;
d) at end of the full test load period;
e) after the relaxation period.
6 © ISO 2004 – All rights reserved
---------------------- Page: 18 ----------------------
SIST EN ISO 8611-1:2004
ISO 8611-1:2004(E)
8.3 Test No. 3 — Air bag bending tests
8.3.1 Purpose
The purpose of this form of bending test is to simulate, as near as is practically feasible, certain load
applications as commonly encountered in the field. The load applicator used for this bending test is an analog
for common uniform flexible loads often supported by pallets, such as cased or bagged goods.
This uniform flexible load analog is used when, under certain circumstances, the primary load applicators, as
described in 8.1.2, cannot be used, or when the application of simulated uniform loads can aid the pallet
designer in selecting the most appropriate pallet for a given use.
8.3.2 Procedure
8.3.2.1 In order to establish the weakest pallet support direction, test one pallet across the length of the
pallet and then a second pallet across the width of the pallet. There is no requirement for further tests on the
stronger dimension unless the result is within 15 % of the weaker.
8.3.2.2 The load applicator shall be a medium or low-pressure envelope air bag, commonly called a
“lifting” or “dunnage” bag, shown schematically in Figure 3. Air bags of this type are specified by size (length
and width), containment (maximum working pressure) and stroke (maximum unrestricted expansion in bag
height).
8.3.2.3 The size of a bag shall be such that when inflated, the bag is in contact with the entire deck of the
pallet. This is often possible with bags approximately 150 mm longer and wider than the top deck of the pallet
to be tested.
8.3.2.4 When bag sides overhang the pallet by more than 75 mm on either edge or end, an air bag
support beam is necessary to maintain the bag overhang at the same level as the upper pallet deck during
testing.
When the load applied to the pallet is measured above the pallet during the test, the supports shown in
Figure 3 a) (4 in the key) shall not be used and the bag should fit the pallet as described in 8.3.2.3.
8.3.2.5 The containment or working pressure in the bag shall be adequate to structurally fail all pallets to
2 2
be tested. Experience indicates that the working pressure shall be at least 0,07 N/mm to 0,08 N/mm .
8.3.2.6 The stroke or level of expansion in bag height depends on the design of the testing apparatus.
Where expansion varies along the centre or edges of the bag, the region of least expansion shall govern bag
selection. In order to avoid the influence of bag stiffness on the test data, the bag expansion shall be at least
twice that necessary to cause pallet failure. The pallet supports as described in Figure 1 shall be positioned
with their centrelines 75 mm from the outer edges of the pallet.
8.3.2.7 Loading or testing rates shall be controlled by appropriately inflating the restrained air bag by
pressing the inflated air bag onto the upper pallet deck.
© ISO 2004 – All
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.