SIST EN ISO 14910-2:2013

Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013)

ISO 14910-2:2013 specifies the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyester/ester and polyether/ester moulding and extrusion materials. Requirements for handling test material and/or for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens in a specified state and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize thermoplastic polyester/ester and polyether/ester moulding and extrusion materials are listed.

Kunststoffe - Thermoplastische Polyester/Ester- und Polyether/Ester-Elastomer-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 14910-2:2013)

Dieser Teil von ISO 14910 legt die Verfahren zur Herstellung von Probekörpern und die anzuwendenden Norm-Prüfverfahren für die Bestimmung der Eigenschaften von thermoplastischen Polyester/Ester- und Polyether/Ester-Formmassen fest. In der Norm werden die Anforderungen an die Handhabung des Prüfwerkstoffs und/oder an die Konditionierung des Prüfwerkstoffs sowohl vor der Formgebung als auch der fertigen Probekörper vor der Prüfung angegeben.
Angegeben werden Verfahren und Bedingungen für die Herstellung der Probekörper in einem bestimmten Zustand und Verfahren zum Messen der Eigenschaften des Werkstoffs, aus dem diese Probekörper hergestellt werden. Aufgeführt sind die Eigenschaften und Prüfverfahren, die geeignet und notwendig sind, um die thermoplastischen Polyester/Ester- und Polyether/Ester-Formmassen (TPC) zu charakterisieren.
Die Eigenschaften wurden von den allgemeinen Prüfverfahren in ISO 10350-1 ausgewählt. Weitere Prüfverfahren, die bei diesen Formmassen häufig angewendet werden oder von besonderer Bedeutung sind, wie die in ISO 14910-1 festgelegten kennzeichnenden Eigenschaften (Härte, Schmelztemperatur und Zugmodul), sind ebenfalls in dem vorliegenden Teil von ISO 14910 enthalten.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erzielen, ist es notwendig, die in diesem Teil der ISO 14910 angegebenen Herstellung- und Konditionierungsverfahren, Probekörpermaße und Prüfverfahren anzuwenden. Die ermittelten Messergebnisse müssen nicht notwendigerweise mit denen identisch sein, die mit Probekörpern anderer Maße oder Probekörper, die nach anderen Verfahren hergestellt wurden, erhalten wurden.
ANMERKUNG Dieser Teil von ISO 14910 wurde in Anlehnung an ISO 10350-1 erstellt, da es für thermoplastische Elastomere gegenwärtig keine entsprechende Norm gibt. Nach Veröffentlichung dieses Teils der ISO 14910 und der analogen Norm für Polyurethane (ISO 16365-2) ist beabsichtigt, ISO 10350-3 für die Ermittlung und Darstellung von vergleichbaren Einpunktkennwerten für thermoplastische Elastomere auf Grundlage dieses Teil von ISO 14910 und ISO 16365-2 zu erstellen, der später weitere Werkstoffnormen für thermoplastische Elastomere folgen werden.

Plastiques - Élastomères thermoplastiques à base de polyester/ester et polyéther/ester, pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 14910-2:2013)

L'ISO 14910-2:2013 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai normalisées à utiliser pour déterminer les propriétés des thermoplastiques à base de polyester/ester et polyéther/ester pour moulage et extrusion. Les exigences relatives à la manipulation et/ou au conditionnement du matériau à évaluer et des éprouvettes avant essai sont indiquées.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes de matériaux dans un état défini, ainsi que les méthodes de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues sont donnés. Les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux thermoplastiques à base de polyester/ester et polyéther/ester pour moulage et extrusion sont énumérées.

Polimerni materiali - Plastomerni poliester/ester in polieter/ester elastomeri za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 14910-2:2013)

Ta del standarda ISO 14910 določa metode za pripravo preskušancev in standardne preskusne metode, ki jih je treba uporabiti pri ugotavljanju lastnosti plastomernih poliester/ester in polieter/ester elastomerov za oblikovanje in ekstrudiranje. Podane so zahteve za upravljanje s preskusnimi materiali in/ali tretiranje preskusnega materiala pred oblikovanjem ter preskušancev pred preskusom. Podani so postopki in pogoji za pripravo preskušancev v določenem stanju in postopki za merjenje lastnosti materialov, iz katerih so preskušanci izdelani. Navedene so lastnosti in preskusne metode, ki so primerne in nujne za opredelitev materialov za oblikovanje in ekstrudiranje plastomernih poliester/ester in polieter/ester elastomerov. Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki so v splošni uporabi ali posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta del standarda ISO 14910. Vključene so tudi označevalne lastnosti, ki so navedene v standardu ISO 14910-1 (trdnost, temperatura taljenja in natezni moduli). Da se zagotovijo primerljivi in ponovljivi rezultati preskusa, je potrebno uporabljati metode priprave in tretiranja, mere preskušanca ter preskusne postopke, ki so navedeni v tem delu standarda ISO 14910. Pri tem ni nujno, da bodo ugotovljene vrednosti enake tistim, ki so pridobljene z uporabo preskušancev, ki imajo drugačne mere ali so pripravljeni z uporabo drugih postopkov.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 19-Jul-2010
• Publication Date: 05-May-2013
• Withdrawal Date: 18-Feb-2018
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 19-Feb-2018
• Due Date: 14-Mar-2018
• Completion Date: 19-Feb-2018
• Ref Project: EN ISO 14910-2:2013 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15)

Relations

• Replaces: SIST EN ISO 14910-2:2006 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:1997)
• Effective Date: 01-Jun-2013
• Replaced By: SIST EN ISO 20029-2:2018 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017)
• Effective Date: 14-Feb-2018
• Revised: SIST EN ISO 20029-2:2018 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017)
• Effective Date: 01-Dec-2015
• Revised: SIST EN ISO 14910-2:2006 - Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:1997)
• Effective Date: 01-Jun-2010

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2013
1DGRPHãþD
SIST EN ISO 14910-2:2006
Polimerni materiali - Plastomerni poliester/ester in polieter/ester elastomeri za
oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje
lastnosti (ISO 14910-2:2013)
Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and
extrusion - Part 2: Preparation of test specimens and determination of properties (ISO
14910-2:2013)
Kunststoffe - Thermoplastische Polyester/Ester- und Polyether/Ester-Elastomer-
Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften
(ISO 14910-2:2013)
Plastiques - Élastomères thermoplastiques à base de polyester/ester et polyéther/ester,
pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des
propriétés (ISO 14910-2:2013)
Ta slovenski standard je istoveten z: EN ISO 14910-2:2013
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14910-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2013
ICS 83.080.20 Supersedes EN ISO 14910-2:2006
English Version
Plastics - Thermoplastic polyester/ester and polyether/ester
elastomers for moulding and extrusion - Part 2: Preparation of
test specimens and determination of properties (ISO 14910-
2:2013)
Plastiques - Élastomères thermoplastiques à base de Kunststoffe - Thermoplastische Polyester/Ester- und
polyester/ester et polyéther/ester, pour moulage et Polyether/Ester-Elastomer-Formmassen - Teil 2:
extrusion - Partie 2: Préparation des éprouvettes et Herstellung von Probekörpern und Bestimmung von
détermination des propriétés (ISO 14910-2:2013) Eigenschaften (ISO 14910-2:2013)
This European Standard was approved by CEN on 1 December 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14910-2:2013: E
worldwide for CEN national Members.

Contents Page
Foreword . 3

Foreword
This document (EN ISO 14910-2:2013) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2013, and conflicting national standards shall be
withdrawn at the latest by September 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14910-2:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14910-2:2013 has been approved by CEN as EN ISO 14910-2:2013 without any modification.

INTERNATIONAL ISO
STANDARD 14910-2
Second edition
2013-03-01
Plastics — Thermoplastic polyester/
ester and polyether/ester elastomers
for moulding and extrusion —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Élastomères thermoplastiques à base de polyester/ester
et polyéther/ester, pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 14910-2:2013(E)
©
ISO 2013
ISO 14910-2:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 14910-2:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Preparation of test specimens . 3
3.1 Treatment of the material before moulding . 3
3.2 Injection moulding . 3
4 Conditioning of test specimens . 4
5 Determination of properties . 4
5.1 General . 4
5.2 Shore D hardness ≤ 25 . 6
5.3 25 < Shore D hardness ≤ 65 . 8
5.4 Shore D hardness > 65 .11
Bibliography .14
ISO 14910-2:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14910-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This second edition cancels and replaces the first edition (ISO 14910-2:1997), which has been
technically revised.
ISO 14910 consists of the following parts, under the general title Plastics — Thermoplastic polyester/ester
and polyether/ester elastomers for moulding and extrusion:
— Part 1: Designation system and basis for specification
— Part 2: Preparation of test specimens and determination of properties
iv © ISO 2013 – All rights reserved

Plastics
ISO 14910-2:2013(E)
Introduction
The structure of thermoplastic-elastomer material standards is based on the following considerations.
For each type of thermoplastic elastomer, reference is made to the relevant material standard.
Thermoplastic-elastomer materials are classified into three classes according to the primary
elastomeric property, hardness, as shown in Figure 1 below. This classification on the basis of hardness
reflects the special position of thermoplastic elastomers between rubber materials on the one hand
and plastics on the other.
Each class is subdivided into standard properties and special properties. The classes have many standard
properties and many special properties in common. Furthermore, a standard property in one class can
be a special property in another class and vice versa.
Special properties are those properties which are in wide use or of particular significance in the practical
characterization of a specific material.
Classification of TPEs
Class 1 Class 2 Class 3
25 < Shore D
Shore D ≤ 25  Shore D > 65
≤ 65
Standard Standard Standard
properties properties properties

Special Special Special
properties properties properties
Figure 1 — Classification of thermoplastic elastomers on the basis of their hardness
Rubbers
INTERNATIONAL STANDARD ISO 14910-2:2013(E)
Plastics — Thermoplastic polyester/ester and polyether/
ester elastomers for moulding and extrusion —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This part of ISO 14910 specifies the methods of preparation of test specimens and the standard test
methods to be used in determining the properties of thermoplastic polyester/ester and polyether/ester
moulding and extrusion materials. Requirements for handling test material and/or for conditioning
both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens in a specified state and procedures
for measuring properties of the materials from which these specimens are made are given. Properties
and test methods which are suitable and necessary to characterize thermoplastic polyester/ester and
polyether/ester moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for or of particular significance to these moulding and extrusion materials are also included
in this part of ISO 14910, as are the designatory properties specified in ISO 14910-1 (hardness, melting
temperature and tensile modulus).
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified in this part
of ISO 14910. Values determined will not necessarily be identical to those obtained using specimens of
different dimensions or prepared using different procedures.
NOTE This part of ISO 149
...