SIST EN ISO 13130:2011
(Main)Laboratory glassware - Desiccators (ISO 13130:2011)
Laboratory glassware - Desiccators (ISO 13130:2011)
This International Standard specifies requirements and tests for desiccators and vacuum desiccators intended for general laboratory purposes such as drying of substances or material.
Laborgeräte aus Glas - Exsikkatoren (ISO 13130:2011)
Diese Internationale Norm legt Anforderungen und Prüfungen für Exsikkatoren und Vakuumexsikkatoren fest, die für allgemeine Laborarbeiten gedacht sind, z. B. zur Trocknung von Substanzen oder Werkstücken.
Verrerie de laboratoire - Dessicateurs (ISO 13130:2011)
L'ISO 13130:2011 spécifie les exigences et les essais relatifs aux dessiccateurs et dessiccateurs sous vide destinés à des utilisations générales en laboratoire, comme le séchage de substances ou de matériaux.
Laboratorijska steklovina - Eksikatorji (ISO 13130:2011)
Ta mednarodni standard določa zahteve in preskuse za eksikatorje in vakuumske eksikatorje za splošno laboratorijsko delo, kot je sušenje snovi ali materialov.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13130:2011
01-oktober-2011
Laboratorijska steklovina - Eksikatorji (ISO 13130:2011)
Laboratory glassware - Desiccators (ISO 13130:2011)
Laborgeräte aus Glas - Exsikkatoren (ISO 13130:2011)
Verrerie de laboratoire - Dessicateurs (ISO 13130:2011)
Ta slovenski standard je istoveten z: EN ISO 13130:2011
ICS:
71.040.20 Laboratorijska posoda in Laboratory ware and related
aparati apparatus
SIST EN ISO 13130:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13130:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 13130:2011
EUROPEAN STANDARD
EN ISO 13130
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 71.040.20; 11.100.01
English Version
Laboratory glassware - Desiccators (ISO 13130:2011)
Verrerie de laboratoire - Dessicateurs (ISO 13130:2011) Laborgeräte aus Glas - Exsikkatoren (ISO 13130:2011)
This European Standard was approved by CEN on 14 July 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13130:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13130:2011
EN ISO 13130:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13130:2011
EN ISO 13130:2011 (E)
Foreword
This document (EN ISO 13130:2011) has been prepared by Technical Committee ISO/TC 48 "Laboratory
equipment" in collaboration with Technical Committee CEN/TC 332 “Laboratory equipment” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at
the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13130:2011 has been approved by CEN as a EN ISO 13130:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13130:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 13130:2011
INTERNATIONAL ISO
STANDARD 13130
First edition
2011-07-15
Laboratory glassware — Desiccators
Verrerie de laboratoire — Dessiccateurs
Reference number
ISO 13130:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 13130:2011
ISO 13130:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13130:2011
ISO 13130:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13130 was prepared by Technical Committee ISO/TC 48, Laboratory equipment, Subcommittee SC 6,
Glass and plastics ware including volumetric instruments.
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13130:2011
---------------------- Page: 10 ----------------------
SIST EN ISO 13130:2011
INTERNATIONAL STANDARD ISO 13130:2011(E)
Laboratory glassware — Desiccators
1 Scope
This International Standard specifies requirements and tests for desiccators and vacuum desiccators intended
for general laboratory purposes such as drying of substances or material.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 383, Laboratory glassware — Interchangeable conical ground joints
ISO 718, Laboratory glassware — Thermal shock and thermal shock endurance — Test methods
ISO 3585, Borosilicate glass 3.3 — Properties
3 Types
Two types of desiccators are specified in this International Standard.
Type 1 – Vacuum desiccators
Type 2 – Non-vacuum desiccators
4 Nominal sizes and series
Desiccators shall have the following nominal sizes and dimensions.
Series A – Nominal sizes 100, 150, 200, 250 and 300 mm – Dimensions in accordance with Table 1
Series B – Nominal sizes 100, 110, 150, 160, 200, 250 and 300 mm – Dimensions in accordance with
Table 2
5 Designation
Desiccators in accordance with this International Standard shall be designated by their nominal size followed
by the type and the series.
Designation of a vacuum desiccator with nominal size of 200 mm, Type 1, Series B:
Desiccator ISO 13130 – 200 – 1B
© ISO 2011 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 13130:2011
ISO 13130:2011(E)
If bodie
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.