SIST EN 300 674-2-1 V3.1.1:2022
(Main)Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum - Sub-part 1: Road Side Units (RSU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum - Sub-part 1: Road Side Units (RSU)
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems intended to be operated as Road Side Units (RSU) with the following characteristics:
• with a Radio Frequency (RF) connection and specified antenna or with an integral antenna;
• used for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band (see also table 1).
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško (osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500 kbit/s / 250 kbit/s), ki deluje v frekvenčnem pasu od 5795 MHz do 5815 MHz - 2. del: Harmonizirani standard za dostop do radijskega spektra - 1. poddel: Obcestne enote (RSU)
Ta dokument določa tehnične značilnosti in metode merjenja za sisteme transportne in prometne telematike (TTT), ki so zasnovani tako, da delujejo kot obcestne enote (RSU) z naslednjimi značilnostmi: • z radiofrekvenčno (RF) povezavo in ustrezno anteno ali z vgrajeno anteno; • uporaba samo za prenos podatkov; • delovanje v frekvenčnem pasu od 5795 MHz do 5815 MHz (glej tudi preglednico 1). OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.3] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 300 674-2-1 V3.1.1 (2022-03)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 1 ----------------------
2 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Reference
REN/ERM-TG37-271
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Units . 11
4.2 General characteristics . 11
4.2.1 RSU classes . 11
4.2.2 Carrier frequencies . 12
4.2.3 Modulation . 12
4.2.4 Antenna characteristic . 12
4.3 Testing for compliance with technical requirements . 12
4.3.1 Environmental conditions for testing . 12
4.3.2 Environmental test conditions. 13
4.3.2.1 General . 13
4.3.2.2 Normal test conditions . 13
4.3.2.3 Extreme test conditions . 13
4.3.3 Power supply . 13
4.4 Conformance requirements . 13
4.4.1 General requirements . 13
4.4.2 Transmitter requirements . 13
4.4.2.1 Maximum equivalent isotropically radiated power . 13
4.4.2.1.1 Definition. 13
4.4.2.1.2 Limit . 13
4.4.2.1.3 Conformance . 13
4.4.2.2 Transmitter frequency error . 14
4.4.2.2.1 Definition. 14
4.4.2.2.2 Limit . 14
4.4.2.2.3 Conformance . 14
4.4.2.3 Transmitter spectrum mask . 14
4.4.2.3.1 Definition. 14
4.4.2.3.2 Limits . 14
4.4.2.3.3 Conformance . 16
4.4.2.4 Transmitter unwanted emissions . 16
4.4.2.4.1 Definition. 16
4.4.2.4.2 Limits . 16
4.4.2.4.3 Conformance . 16
4.4.3 Receiver requirements . 17
4.4.3.1 Receiver unwanted emissions . 17
4.4.3.1.1 Definition. 17
4.4.3.1.2 Limits . 17
4.4.3.1.3 Conformance . 17
4.4.3.2 Receiver selectivity . 17
4.4.3.2.1 Receiver blocking . 17
4.4.3.2.2 Receiver adjacent channel selectivity . 18
4.4.3.2.3 Receiver co-channel rejection . 18
4.4.3.3 Receiver dynamic range and sensitivity . 19
4.4.3.3.1 Receiver sensitivity . 19
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
4.4.3.3.2 Receiver dynamic range . 19
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Radio test suites . 20
5.2.1 Transmitter parameter tests . 20
5.2.1.1 Maximum equivalent isotropically radiated power . 20
5.2.1.2 Transmitter frequency error . 21
5.2.1.3 Transmitter spectrum mask . 21
5.2.1.4 Transmitter unwanted emissions . 22
5.2.2 Receiver parameter tests . 23
5.2.2.1 Receiver unwanted emissions in the spurious domain . 23
5.2.2.2 Receiver selectivity . 24
5.2.2.2.1 General Requirements and prerequisites for testing . 24
5.2.2.2.2 Receiver blocking test execution . 24
5.2.2.2.3 Receiver adjacent channel selectivity test execution . 25
5.2.2.2.4 Receiver co-channel rejection test execution. 25
5.2.2.3 Receiver dynamic range and sensitivity test execution . 26
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): General condition for testing and test setup . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 31
B.1.4 Shielded anechoic chamber . 31
B.1.5 RF cables . 32
B.1.6 Splitter . 32
B.1.7 Spectrum analyser . 33
B.2 Conducted measurements . 33
B.2.1 Test site requirements . 33
B.2.2 Test arrangement for conducted Tx parameter measurements . 33
B.3 Radiated measurements . 34
B.3.1 Test site requirements . 34
B.3.1.1 Measurement distances . 34
B.3.1.2 Substitution method . 34
B.3.1.3 Test and substitution antennas . 35
B.3.2 Test arrangement for the radiated measurement of the transmit parameters . 35
B.3.3 Arrangement for radiated measurements of the receiver parameters . 36
B.3.4 Antenna decoupling loss . 39
B.4 RSU carrier modulation. 39
B.5 Bit error ratio measurements . 40
B.5.1 Basics . 40
B.5.2 BER measurement . 40
B.5.3 FER measurement . 40
B.5.3.1 Mathematical expressions . 40
B.5.3.2 Equipment . 41
B.5.3.3 Procedure . 41
Annex C (informative): Maximum Measurement Uncertainty . 42
Annex D (informative): Checklist . 43
Annex E (informative): Bibliography . 44
Annex F (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document complies with the Commission Implementing Decision (EU) 2019/1345 [i.1] and CEPT/ERC
Recommendation 70-03 [i.2].
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
National transposition dates
Date of adoption of this EN: 24 January 2022
Date of latest announcement of this EN (doa): 30 April 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2022
Date of withdrawal of any conflicting National Standard (dow): 31 October 2023
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems intended to be operated as Road Side Units (RSU) with the following characteristics:
• with a Radio Frequency (RF) connection and specified antenna or with an integral antenna;
• used for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band (see also table 1).
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range communication -
Physical layer using microwave at 5,8 GHz", (produced by CEN).
[2] ISO 14906:2018/AMD 1:2020: "Electronic fee collection -- Application interface definition for
dedicated short-range communication -- Amendment 1".
[3] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document, but they assist the
user with regard to a particular subject area.
[i.1] Commission Implementing Decision (EU) 2019/1345 of 2 August 2019 amending Decision
2006/771/EC updating harmonised technical conditions in the area of radio spectrum use for
short-range devices.
[i.2] CEPT/ERC Recommendation 70-03 (2020): "Relating to the use of Short Range Devices (SRD)".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.5] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.6] CEPT/ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in Directive 2014/53/EU [i.3] and the following apply:
adjacent channel: channel at a distance of 5 MHz relative to the centre frequency, i.e. in the channel at the next upper
or lower centre frequency
bit: acronym for "binary digit" which can have one out of two possible values
EXAMPLE: 0/1, or +1/-1, or low/high.
bit rate: number of bits occurring per unit time, usually expressed in bits per second
boresight: direction of maximum radiation of a directional antenna
carrier frequency: frequency f to which the RSU transmitter is tuned
Tx
carrier signal or carrier: harmonic signal whose nominal single frequency f is capable of being modulated by a
Tx
second, symbol-carrying signal
channel: continuous part of the radio-frequency spectrum to be used for a specified emission or transmission
NOTE: A radio-frequency channel may be defined by two specified limits, or by its centre frequency and its
bandwidth, or any equivalent indication. It is often designated by a sequential number. A radio-frequency
channel may be time-shared in order to allow radio communication in both directions by simplex
operation. The term "channel" is sometimes used to denote two associated radio-frequency channels, each
of which is used for one of two directions of transmission, i.e. in fact a telecommunication circuit.
co-channel: transmission using the same uplink or downlink channel in a frequency band of 5 MHz width
Cross-Polar Discrimination
...
SLOVENSKI STANDARD
SIST EN 300 674-2-1 V3.1.1:2022
01-maj-2022
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško
(osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500
kbit/s / 250 kbit/s), ki deluje v frekvenčnem pasu od 5795 MHz do 5815 MHz - 2. del:
Harmonizirani standard za dostop do radijskega spektra - 1. poddel: Obcestne
enote (RSU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication
(DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5
815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum -
Sub-part 1: Road Side Units (RSU)
Ta slovenski standard je istoveten z: ETSI EN 300 674-2-1 V3.1.1 (2022-03)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
SIST EN 300 674-2-1 V3.1.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
---------------------- Page: 2 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
ETSI EN 300 674-2-1 V3.1.1 (2022-03)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 3 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
2 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Reference
REN/ERM-TG37-271
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
3 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Units . 11
4.2 General characteristics . 11
4.2.1 RSU classes . 11
4.2.2 Carrier frequencies . 12
4.2.3 Modulation . 12
4.2.4 Antenna characteristic . 12
4.3 Testing for compliance with technical requirements . 12
4.3.1 Environmental conditions for testing . 12
4.3.2 Environmental test conditions. 13
4.3.2.1 General . 13
4.3.2.2 Normal test conditions . 13
4.3.2.3 Extreme test conditions . 13
4.3.3 Power supply . 13
4.4 Conformance requirements . 13
4.4.1 General requirements . 13
4.4.2 Transmitter requirements . 13
4.4.2.1 Maximum equivalent isotropically radiated power . 13
4.4.2.1.1 Definition. 13
4.4.2.1.2 Limit . 13
4.4.2.1.3 Conformance . 13
4.4.2.2 Transmitter frequency error . 14
4.4.2.2.1 Definition. 14
4.4.2.2.2 Limit . 14
4.4.2.2.3 Conformance . 14
4.4.2.3 Transmitter spectrum mask . 14
4.4.2.3.1 Definition. 14
4.4.2.3.2 Limits . 14
4.4.2.3.3 Conformance . 16
4.4.2.4 Transmitter unwanted emissions . 16
4.4.2.4.1 Definition. 16
4.4.2.4.2 Limits . 16
4.4.2.4.3 Conformance . 16
4.4.3 Receiver requirements . 17
4.4.3.1 Receiver unwanted emissions . 17
4.4.3.1.1 Definition. 17
4.4.3.1.2 Limits . 17
4.4.3.1.3 Conformance . 17
4.4.3.2 Receiver selectivity . 17
4.4.3.2.1 Receiver blocking . 17
4.4.3.2.2 Receiver adjacent channel selectivity . 18
4.4.3.2.3 Receiver co-channel rejection . 18
4.4.3.3 Receiver dynamic range and sensitivity . 19
4.4.3.3.1 Receiver sensitivity . 19
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
4 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
4.4.3.3.2 Receiver dynamic range . 19
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Radio test suites . 20
5.2.1 Transmitter parameter tests . 20
5.2.1.1 Maximum equivalent isotropically radiated power . 20
5.2.1.2 Transmitter frequency error . 21
5.2.1.3 Transmitter spectrum mask . 21
5.2.1.4 Transmitter unwanted emissions . 22
5.2.2 Receiver parameter tests . 23
5.2.2.1 Receiver unwanted emissions in the spurious domain . 23
5.2.2.2 Receiver selectivity . 24
5.2.2.2.1 General Requirements and prerequisites for testing . 24
5.2.2.2.2 Receiver blocking test execution . 24
5.2.2.2.3 Receiver adjacent channel selectivity test execution . 25
5.2.2.2.4 Receiver co-channel rejection test execution. 25
5.2.2.3 Receiver dynamic range and sensitivity test execution . 26
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): General condition for testing and test setup . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 31
B.1.4 Shielded anechoic chamber . 31
B.1.5 RF cables . 32
B.1.6 Splitter . 32
B.1.7 Spectrum analyser . 33
B.2 Conducted measurements . 33
B.2.1 Test site requirements . 33
B.2.2 Test arrangement for conducted Tx parameter measurements . 33
B.3 Radiated measurements . 34
B.3.1 Test site requirements . 34
B.3.1.1 Measurement distances . 34
B.3.1.2 Substitution method . 34
B.3.1.3 Test and substitution antennas . 35
B.3.2 Test arrangement for the radiated measurement of the transmit parameters . 35
B.3.3 Arrangement for radiated measurements of the receiver parameters . 36
B.3.4 Antenna decoupling loss . 39
B.4 RSU carrier modulation. 39
B.5 Bit error ratio measurements . 40
B.5.1 Basics . 40
B.5.2 BER measurement . 40
B.5.3 FER measurement . 40
B.5.3.1 Mathematical expressions . 40
B.5.3.2 Equipment . 41
B.5.3.3 Procedure . 41
Annex C (informative): Maximum Measurement Uncertainty . 42
Annex D (informative): Checklist . 43
Annex E (informative): Bibliography . 44
Annex F (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
5 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document complies with the Commission Implementing Decision (EU) 2019/1345 [i.1] and CEPT/ERC
Recommendation 70-03 [i.2].
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
ETSI
---------------------- Page: 7 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
6 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
National transposition dates
Date of adoption of this EN: 24 January 2022
Date of latest announcement of this EN (doa): 30 April 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2022
Date of withdrawal of any conflicting National Standard (dow): 31 October 2023
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
7 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems intended to be operated as Road Side Units (RSU) with the following characteristics:
• with a Radio Frequency (RF) connection and specified antenna or with an integral antenna;
• used for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band (see also table 1).
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range communication -
Physical layer using microwave at 5,8 GHz", (produced by CEN).
[2] ISO 14906:2018/AMD 1:2020: "Electronic fee collection -- Application interface definition for
dedicated short-range communication -- Amendment 1".
[3] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document, but they assist the
user with regard to a particular subject area.
[i.1] Commission Implementing Decision (EU) 2019/1345 of 2 August 2019 amending Decision
2006/771/EC updating harmonised technical conditions in the area of radio spectrum use for
short-range devices.
[i.2] CEPT/ERC Recommendation 70-03 (2020): "Relating to the use of Short Range Devices (SRD)".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 300 674-2-1 V3.1.1:2022
8 ETSI EN 300 674-2-1 V3.1.1 (2022-03)
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.5] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.6] CEPT/ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the p
...
Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Reference
REN/ERM-TG37-271
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Units . 11
4.2 General characteristics . 11
4.2.1 RSU classes . 11
4.2.2 Carrier frequencies . 12
4.2.3 Modulation . 12
4.2.4 Antenna characteristic . 12
4.3 Testing for compliance with technical requirements . 12
4.3.1 Environmental conditions for testing . 12
4.3.2 Environmental test conditions. 13
4.3.2.1 General . 13
4.3.2.2 Normal test conditions . 13
4.3.2.3 Extreme test conditions . 13
4.3.3 Power supply . 13
4.4 Conformance requirements . 13
4.4.1 General requirements . 13
4.4.2 Transmitter requirements . 13
4.4.2.1 Maximum equivalent isotropically radiated power . 13
4.4.2.1.1 Definition. 13
4.4.2.1.2 Limit . 13
4.4.2.1.3 Conformance . 13
4.4.2.2 Transmitter frequency error . 14
4.4.2.2.1 Definition. 14
4.4.2.2.2 Limit . 14
4.4.2.2.3 Conformance . 14
4.4.2.3 Transmitter spectrum mask . 14
4.4.2.3.1 Definition. 14
4.4.2.3.2 Limits . 14
4.4.2.3.3 Conformance . 16
4.4.2.4 Transmitter unwanted emissions . 16
4.4.2.4.1 Definition. 16
4.4.2.4.2 Limits . 16
4.4.2.4.3 Conformance . 16
4.4.3 Receiver requirements . 17
4.4.3.1 Receiver unwanted emissions . 17
4.4.3.1.1 Definition. 17
4.4.3.1.2 Limits . 17
4.4.3.1.3 Conformance . 17
4.4.3.2 Receiver selectivity . 17
4.4.3.2.1 Receiver blocking . 17
4.4.3.2.2 Receiver adjacent channel selectivity . 18
4.4.3.2.3 Receiver co-channel rejection . 18
4.4.3.3 Receiver dynamic range and sensitivity . 19
4.4.3.3.1 Receiver sensitivity . 19
4.4.3.3.2 Receiver dynamic range . 19
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Radio test suites . 20
5.2.1 Transmitter parameter tests . 20
5.2.1.1 Maximum equivalent isotropically radiated power . 20
5.2.1.2 Transmitter frequency error . 21
5.2.1.3 Transmitter spectrum mask . 21
5.2.1.4 Transmitter unwanted emissions . 22
5.2.2 Receiver parameter tests . 23
5.2.2.1 Receiver unwanted emissions in the spurious domain . 23
5.2.2.2 Receiver selectivity . 24
5.2.2.2.1 General Requirements and prerequisites for testing . 24
5.2.2.2.2 Receiver blocking test execution . 24
5.2.2.2.3 Receiver adjacent channel selectivity test execution . 25
5.2.2.2.4 Receiver co-channel rejection test execution. 25
5.2.2.3 Receiver dynamic range and sensitivity test execution . 26
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): General condition for testing and test setup . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 31
B.1.4 Shielded anechoic chamber . 31
B.1.5 RF cables . 32
B.1.6 Splitter . 32
B.1.7 Spectrum analyser . 33
B.2 Conducted measurements . 33
B.2.1 Test site requirements . 33
B.2.2 Test arrangement for conducted Tx parameter measurements . 33
B.3 Radiated measurements . 34
B.3.1 Test site requirements . 34
B.3.1.1 Measurement distances . 34
B.3.1.2 Substitution method . 34
B.3.1.3 Test and substitution antennas . 35
B.3.2 Test arrangement for the radiated measurement of the transmit parameters . 35
B.3.3 Arrangement for radiated measurements of the receiver parameters . 36
B.3.4 Antenna decoupling loss . 39
B.4 RSU carrier modulation. 39
B.5 Bit error ratio measurements . 40
B.5.1 Basics . 40
B.5.2 BER measurement . 40
B.5.3 FER measurement . 40
B.5.3.1 Mathematical expressions . 40
B.5.3.2 Equipment . 41
B.5.3.3 Procedure . 41
Annex C (informative): Maximum Measurement Uncertainty . 42
Annex D (informative): Checklist . 43
Annex E (informative): Bibliography . 44
Annex F (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document complies with the Commission Implementing Decision (EU) 2019/1345 [i.1] and CEPT/ERC
Recommendation 70-03 [i.2].
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems intended to be operated as Road Side Units (RSU) with the following characteristics:
• with a Radio Frequency (RF) connection and specified antenna or with an integral antenna;
• used for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band (see also table 1).
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range communication -
Physical layer using microwave at 5,8 GHz", (produced by CEN).
[2] ISO 14906:2018/AMD 1:2020: "Electronic fee collection -- Application interface definition for
dedicated short-range communication -- Amendment 1".
[3] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document, but they assist the
user with regard to a particular subject area.
[i.1] Commission Implementing Decision (EU) 2019/1345 of 2 August 2019 amending Decision
2006/771/EC updating harmonised technical conditions in the area of radio spectrum use for short-
range devices.
[i.2] CEPT/ERC Recommendation 70-03 (2020): "Relating to the use of Short Range Devices (SRD)".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.5] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
2014/53/EU".
[i.6] CEPT/ERC Recommendation 74-01 (2019): "Unwanted emissions in the spurious domain".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the terms given in Directive 2014/53/EU [i.3] and the following apply:
adjacent channel: channel at a distance of 5 MHz relative to the centre frequency, i.e. in the channel at the next upper
or lower centre frequency
bit: acronym for "binary digit" which can have one out of two possible values
EXAMPLE: 0/1, or +1/-1, or low/high.
bit rate: number of bits occurring per unit time, usually expressed in bits per second
boresight: direction of maximum radiation of a directional antenna
carrier frequency: frequency f to which the RSU transmitter is tuned
Tx
carrier signal or carrier: harmonic signal whose nominal single frequency f is capable of being modulated by a
Tx
second, symbol-carrying signal
channel: continuous part of the radio-frequency spectrum to be used for a specified emission or transmission
NOTE: A radio-frequency channel may be defined by two specified limits, or by its centre frequency and its
bandwidth, or any equivalent indication. It is often designated by a sequential number. A radio-frequency
channel may be time-shared in order to allow radio communication in both directions by simplex
operation. The term "channel" is sometimes used to denote two associated radio-frequency channels, each
of which is used for one of two directions of transmission, i.e. in fact a t
...
SLOVENSKI STANDARD
oSIST prEN 300 674-2-1 V3.0.1:2022
01-januar-2022
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško
(osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500
kbit/s / 250 kbit/s), ki deluje v frekvenčnem pasu od 5795 MHz do 5815 MHz - 2. del:
Harmonizirani standard za dostop do radijskega spektra - 1. poddel: Obcestne
enote (RSU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication
(DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5
815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum -
Sub-part 1: Road Side Units (RSU)
Ta slovenski standard je istoveten z: ETSI EN 300 674-2-1 V3.0.1 (2021-10)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
oSIST prEN 300 674-2-1 V3.0.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
---------------------- Page: 2 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 1: Road Side Units (RSU)
---------------------- Page: 3 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
2 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Reference
REN/ERM-TG37-271
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
3 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 8
3.1 Terms . 8
3.2 Symbols . 9
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Units . 11
4.2 General characteristics . 11
4.2.1 RSU classes . 11
4.2.2 Carrier frequencies . 12
4.2.3 Modulation . 12
4.2.4 Antenna characteristic . 12
4.3 Testing for compliance with technical requirements . 12
4.3.1 Environmental conditions for testing . 12
4.3.2 Environmental test conditions. 13
4.3.2.1 General . 13
4.3.2.2 Normal test conditions . 13
4.3.2.3 Extreme test conditions . 13
4.3.3 Power supply . 13
4.4 Conformance requirements . 13
4.4.1 General requirements . 13
4.4.2 Transmitter requirements . 13
4.4.2.1 Maximum equivalent isotropically radiated power . 13
4.4.2.1.1 Definition. 13
4.4.2.1.2 Limit . 13
4.4.2.1.3 Conformance . 13
4.4.2.2 Transmitter frequency error . 14
4.4.2.2.1 Definition. 14
4.4.2.2.2 Limit . 14
4.4.2.2.3 Conformance . 14
4.4.2.3 Transmitter spectrum mask . 14
4.4.2.3.1 Definition. 14
4.4.2.3.2 Limits . 14
4.4.2.3.3 Conformance . 16
4.4.2.4 Transmitter unwanted emissions . 16
4.4.2.4.1 Definition. 16
4.4.2.4.2 Limits . 16
4.4.2.4.3 Conformance . 16
4.4.3 Receiver requirements . 17
4.4.3.1 Receiver unwanted emissions . 17
4.4.3.1.1 Definition. 17
4.4.3.1.2 Limits . 17
4.4.3.1.3 Conformance . 17
4.4.3.2 Receiver selectivity . 17
4.4.3.2.1 Receiver blocking . 17
4.4.3.2.2 Receiver adjacent channel selectivity . 18
4.4.3.2.3 Receiver co-channel rejection . 18
4.4.3.3 Receiver dynamic range and sensitivity . 19
4.4.3.3.1 Receiver sensitivity . 19
4.4.3.3.2 Receiver dynamic range . 19
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
4 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Radio test suites . 20
5.2.1 Transmitter parameter tests . 20
5.2.1.1 Maximum equivalent isotropically radiated power . 20
5.2.1.2 Transmitter frequency error . 21
5.2.1.3 Transmitter spectrum mask . 21
5.2.1.4 Transmitter unwanted emissions . 22
5.2.2 Receiver parameter tests . 23
5.2.2.1 Receiver unwanted emissions in the spurious domain . 23
5.2.2.2 Receiver selectivity . 24
5.2.2.2.1 General Requirements and prerequisites for testing . 24
5.2.2.2.2 Receiver blocking test execution . 24
5.2.2.2.3 Receiver adjacent channel selectivity test execution . 25
5.2.2.2.4 Receiver co-channel rejection test execution. 25
5.2.2.3 Receiver dynamic range and sensitivity test execution . 26
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 28
Annex B (normative): General condition for testing and test setup . 30
B.1 General conditions . 30
B.1.1 Power source . 30
B.1.2 Thermal balance . 30
B.1.3 Test signals . 31
B.1.4 Shielded anechoic chamber . 31
B.1.5 RF cables . 32
B.1.6 Splitter . 32
B.1.7 Spectrum analyser . 33
B.2 Conducted measurements . 33
B.2.1 Test site requirements . 33
B.2.2 Test arrangement for conducted Tx parameter measurements . 33
B.3 Radiated measurements . 34
B.3.1 Test site requirements . 34
B.3.1.1 Measurement distances . 34
B.3.1.2 Substitution method . 34
B.3.1.3 Test and substitution antennas . 35
B.3.2 Test arrangement for the radiated measurement of the transmit parameters . 35
B.3.3 Arrangement for radiated measurements of the receiver parameters . 36
B.3.4 Antenna decoupling loss . 39
B.4 RSU carrier modulation. 39
B.5 Bit error ratio measurements . 40
B.5.1 Basics . 40
B.5.2 BER measurement . 40
B.5.3 FER measurement . 40
B.5.3.1 Mathematical expressions . 40
B.5.3.2 Equipment . 41
B.5.3.3 Procedure . 41
Annex C (informative): Maximum Measurement Uncertainty . 42
Annex D (informative): Checklist . 43
Annex E (informative): Bibliography . 44
Annex F (informative): Change History . 45
History . 46
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
5 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.3].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document complies with the Commission Implementing Decision (EU) 2019/1345 [i.1] and CEPT/ERC
Recommendation 70-03 [i.2].
The present document is part 2, sub-part 1 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
6 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
7 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems intended to be operated as Road Side Units (RSU) with the following characteristics:
• with a Radio Frequency (RF) connection and specified antenna or with an integral antenna;
• used for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band (see also table 1).
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.3] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] EN 12253:2004: "Road transport and traffic telematics - Dedicated short-range communication -
Physical layer using microwave at 5,8 GHz", (produced by CEN).
[2] ISO 14906:2018/AMD 1:2020: "Electronic fee collection -- Application interface definition for
dedicated short-range communication -- Amendment 1".
[3] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document, but they assist the
user with regard to a particular subject area.
[i.1] Commission Implementing Decision (EU) 2019/1345 of 2 August 2019 amending Decision
2006/771/EC updating harmonised technical conditions in the area of radio spectrum use for short-
range devices.
[i.2] CEPT/ERC Recommendation 70-03 (2020): "Relating to the use of Short Range Devices (SRD)".
[i.3] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 300 674-2-1 V3.0.1:2022
8 Draft ETSI EN 300 674-2-1 V3.0.1 (2021-10)
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.5] ETSI EG 203 336 (V1.2.1) (05-2020): "Guide for the selection of technical parameters for the
production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.