SIST EN ISO 20344:2022
(Main)Personal protective equipment - Test methods for footwear (ISO 20344:2021)
Personal protective equipment - Test methods for footwear (ISO 20344:2021)
This standard specifies methods for testing footwear designed as personal protective equipment.
Persönliche Schutzausrüstung - Prüfverfahren für Schuhe (ISO 20344:2021)
Dieses Dokument legt Prüfverfahren für Schuhwerk fest, das als Persönliche Schutzausrüstung (PSA) konzipiert ist.
Équipement de protection individuelle - Méthodes d'essai pour les chaussures (ISO 20344:2021)
Le présent document spécifie des méthodes d'essai pour les chaussures conçues comme des équipements de protection individuelle.
Osebna varovalna oprema - Metode preskušanja obutve (ISO 20344:2021)
Ta standard določa metode preskušanja obutve, oblikovane kot osebna varovalna oprema.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 20344:2022
01-januar-2022
Nadomešča:
SIST EN ISO 20344:2012
Osebna varovalna oprema - Metode preskušanja obutve (ISO 20344:2021)
Personal protective equipment - Test methods for footwear (ISO 20344:2021)
Persönliche Schutzausrüstung - Prüfverfahren für Schuhe (ISO 20344:2021)
Équipement de protection individuelle - Méthodes d'essai pour les chaussures (ISO
20344:2021)
Ta slovenski standard je istoveten z: EN ISO 20344:2021
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
SIST EN ISO 20344:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 20344:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 20344:2022
EN ISO 20344
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2021
EUROPÄISCHE NORM
ICS 13.340.50 Supersedes EN ISO 20344:2011
English Version
Personal protective equipment - Test methods for
footwear (ISO 20344:2021)
Équipement de protection individuelle - Méthodes Persönliche Schutzausrüstung - Prüfverfahren für
d'essai pour les chaussures (ISO 20344:2021) Schuhe (ISO 20344:2021)
This European Standard was approved by CEN on 10 October 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20344:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 20344:2022
EN ISO 20344:2021 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 20344:2022
EN ISO 20344:2021 (E)
European foreword
This document (EN ISO 20344:2021) has been prepared by Technical Committee ISO/TC 94 "Personal
safety -- Personal protective equipment" in collaboration with Technical Committee CEN/TC 161 “Foot
and leg protectors” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2022, and conflicting national standards shall be
withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20344:2011.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 20344:2021 has been approved by CEN as EN ISO 20344:2021 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 20344:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 20344:2022
INTERNATIONAL ISO
STANDARD 20344
Third edition
2021-10
Personal protective equipment — Test
methods for footwear
Équipement de protection individuelle — Méthodes d'essai pour les
chaussures
Reference number
ISO 20344:2021(E)
© ISO 2021
---------------------- Page: 7 ----------------------
SIST EN ISO 20344:2022
ISO 20344:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2021 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 20344:2022
ISO 20344:2021(E)
Contents Page
Foreword .viii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General testing parameters . 2
4.1 Sampling . 2
4.2 Conditioning before and during the test . 3
4.3 Prerequisites on the testing procedure . 3
4.4 Test report . 3
5 Test methods for whole footwear . 6
5.1 Specific ergonomic features . 6
5.1.1 Sampling and conditioning . 6
5.1.2 Test method . 7
5.1.3 Test report . 7
5.2 Determination of upper/outsole and sole interlayer bond strength . 8
5.2.1 Principle . 8
5.2.2 Test equipment . 8
5.2.3 Sampling and conditioning . 8
5.2.4 Test method . 8
5.2.5 Test report .12
5.3 Determination of dimensions of toecap .12
5.3.1 Sampling and conditioning .12
5.3.2 Test method . 12
5.3.3 Test report .12
5.4 Determination of impact resistance .12
5.4.1 Test equipment .12
5.4.2 Sampling and conditioning . 16
5.4.3 Test methods . 16
5.4.4 Test report . 18
5.5 Determination of compression resistance . 18
5.5.1 Test equipment . 18
5.5.2 Sampling and conditioning . 18
5.5.3 Test method . 18
5.5.4 Test report . 19
5.6 Behaviour of toecaps (thermal and chemical). 20
5.6.1 Sampling and conditioning . 20
5.6.2 Behaviour of toecaps (thermal and chemical) . 20
5.7 Determination of leak proofness . 21
5.7.1 Test equipment . 21
5.7.2 Sampling and conditioning . 21
5.7.3 Test method . 21
5.7.4 Test report . 21
5.8 Dimensions of perforation resistant inserts . 21
5.8.1 Sampling and conditioning . 21
5.8.2 Test method . 22
5.8.3 Test report .22
5.9 Determination of the perforation resistance of footwear with a metallic
perforation resistant insert .23
5.9.1 Test equipment . 23
5.9.2 Sampling and conditioning . 23
5.9.3 Test method . 24
5.9.4 Test report . 24
iii
© ISO 2021 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 20344:2022
ISO 20344:2021(E)
5.10 Determination of the perforation resistance of footwear with a non-metallic
perforation resistant insert . 24
5.10.1 General . 24
5.10.2 Test equipment . 24
5.10.3 Sampling and conditioning . 24
5.10.4 Test method . 25
5.10.5 Test report . 27
5.11 Behaviour of perforation resistant inserts (thermal and chemical) .28
5.11.1 Sampling and conditioning .28
5.11.2 Behaviour of perforation resistant inserts (thermal and chemical) .29
5.11.3 Test report .29
5.12 Determination of the flex resistance of perforation-resistant inserts .29
5.12.1 Sampling and conditioning .29
5.12.2 Test method .29
5.12.3 Test report .29
5.13 Determination of electrical resistance .30
5.13.1 Principle . 30
5.13.2 Test equipment .30
5.13.3 Sampling and conditioning .30
5.13.4 Test method . 31
5.13.5 Test report . 31
5.14 Determination of footwear slip resistance . 31
5.14.1 Sampling and conditioning . 31
5.14.2 Test method . 31
5.14.3 Test report . 32
5.15 Determination of insulation against heat . 32
5.15.1 Test equipment . 32
5.15.2 Sampling and conditioning . 33
5.15.3 Test method . 33
5.15.4 Test report . 33
5.16 Determination of insulation against cold .34
5.16.1 Test equipment .34
5.16.2 Sampling and conditioning .34
5.16.3 Test method . 35
5.16.4 Test report .36
5.17 Determination of energy absorption of the seat region .36
5.17.1 Test equipment .36
5.17.2 Sampling and conditioning .38
5.17.3 Test method .38
5.17.4 Test report .38
5.18 Determination of resistance to water for whole footwear: trough test .38
5.18.1 Principle .38
5.18.2 Test equipment .38
5.18.3 Sampling and conditioning . 39
5.18.4 Test method . 39
5.18.5 Test report .40
5.19 Determination of resistance to water for whole footwear: dynamic test .40
5.19.1 Principle .40
5.19.2 Test equipment .40
5.19.3 Sampling and conditioning .40
5.19.4 Test method .40
5.19.5 Test report . 42
5.20 Determination of impact resistance of a metatarsal protection . 42
5.20.1 Test equipment . 42
5.20.2 Sampling and conditioning . 45
5.20.3 Test method .46
5.20.4 Test report . 47
5.21 Determination of the dimension of the ankle protection . 47
iv
© ISO 2021 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 20344:2022
ISO 20344:2021(E)
5.21.1 Sampling and conditioning . 47
5.21.2 Test method . 47
5.21.3 Test report .48
5.22 Determination of the shock absorption capacity of ankle protection materials
incorporated into the upper .48
5.22.1 Principle .48
5.22.2 Test equipment .49
5.22.3 Sampling and conditioning .50
5.22.4 Test method . 50
5.22.5 Test report .50
5.23 Determination of cutting resistance . 51
5.23.1 Sampling and conditioning . 51
5.23.2 Dimension of the cut resistant protective area . 51
5.23.3 Test method . 52
5.23.4 Test report . 52
5.24 Scuff caps . 52
5.24.1 Sampling and conditioning . 52
5.24.2 Test method for the abrasion resistance of the scuff caps . 52
5.24.3 Test report . 52
5.25 Determination of seam strength . 53
5.25.1 Sampling and conditioning . 53
5.25.2 Test method . 53
5.25.3 Test report .
...
SLOVENSKI STANDARD
oSIST prEN ISO 20344:2020
01-junij-2020
Osebna varovalna oprema - Metode preskušanja obutve (ISO/DIS 20344:2020)
Personal protective equipment - Test methods for footwear (ISO/DIS 20344:2020)
Persönliche Schutzausrüstung - Prüfverfahren für Schuhe (ISO/DIS 20344:2020)
Équipement de protection individuelle - Méthodes d'essai pour les chaussures (ISO/DIS
20344:2020)
Ta slovenski standard je istoveten z: prEN ISO 20344
ICS:
13.340.50 Varovanje nog in stopal Leg and foot protection
oSIST prEN ISO 20344:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 20344:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 20344:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 20344
ISO/TC 94/SC 3 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-04-13 2020-07-06
Personal protective equipment — Test methods for
footwear
Équipement de protection individuelle — Méthodes d'essai pour les chaussures
ICS: 13.340.50
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 20344:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 20344:2020
ISO/DIS 20344:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 20344:2020
ISO/DIS 20344:2020(E)
Contents Page
Foreword .viii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General testing parameters. 2
4.1 Sampling . 2
4.2 Conditioning before and during the test . 3
4.3 Prerequisites on the testing procedure . 3
4.4 Test report . 3
5 Test methods for whole footwear . 5
5.1 Specific ergonomic features . 5
5.1.1 Sampling and conditioning . 5
5.1.2 Test method . 6
5.1.3 Test report . 6
5.2 Determination of upper/outsole and sole interlayer bond strength . 7
5.2.1 Principle . 7
5.2.2 Test equipment . 7
5.2.3 Sampling and conditioning . 7
5.2.4 Test method . 7
5.2.5 Test report .11
5.3 Determination of dimensions of toecap .11
5.3.1 Sampling and conditioning .11
5.3.2 Test method .11
5.3.3 Test report .11
5.4 Determination of impact resistance .12
5.4.1 Test equipment .12
5.4.2 Sampling and conditioning .14
5.4.3 Test methods .14
5.4.4 Test report .16
5.5 Determination of compression resistance .16
5.5.1 Equipment .16
5.5.2 Sampling and conditioning .16
5.5.3 Test method .16
5.5.4 Test report .17
5.6 Behaviour of toecaps (thermal and chemical) .18
5.6.1 Sampling and conditioning .18
5.6.2 Behaviour of toecaps (thermal and chemical) .18
5.7 Determination of leakproofness .19
5.7.1 Test equipment .19
5.7.2 Sampling and conditioning .19
5.7.3 Test method .19
5.7.4 Test report .19
5.8 Dimensions of perforation resistant inserts .19
5.8.1 Sampling and conditioning .19
5.8.2 Test method .19
5.8.3 Test report .20
5.9 Determination of the perforation resistance of footwear with a metallic
perforation resistant insert .20
5.9.1 Test equipment .20
5.9.2 Sampling and conditioning .21
5.9.3 Test method .21
5.9.4 Test report .22
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 20344:2020
ISO/DIS 20344:2020(E)
5.10 Determination of the perforation resistance of footwear with a non-metallic
perforation resistant insert .22
5.10.1 General.22
5.10.2 Equipment .22
5.10.3 Test nail for Type Y, as described in ISO 22568-4:2019, A.1.2. .22
5.10.4 Sampling and conditioning .22
5.10.5 Test method .22
5.10.6 Test report .23
5.11 Behaviour of perforation resistant inserts (thermal and chemical) .24
5.11.1 Sampling and conditioning .24
5.11.2 Behaviour of perforation resistant inserts (thermal and chemical) .25
5.12 Determination of the flex resistance of perforation-resistant inserts .25
5.12.1 Sampling and conditioning .25
5.12.2 Test method .25
5.13 Determination of electrical resistance .25
5.13.1 Principle .25
5.13.2 Equipment .26
5.13.3 Sampling and conditioning .26
5.13.4 Test method .27
5.13.5 Test report .27
5.14 Determination of footwear slip resistance .27
5.14.1 Sampling and conditioning .27
5.14.2 Test method .27
5.15 Determination of insulation against heat .28
5.15.1 Equipment .28
5.15.2 Sampling and conditioning .28
5.15.3 Test method .29
5.15.4 Test report .29
5.16 Determination of insulation against cold .29
5.16.1 Equipment .29
5.16.2 Sampling and conditioning .30
5.16.3 Test method .30
5.16.4 Test report .31
5.17 Determination of energy absorption of the seat region .31
5.17.1 Equipment .31
5.17.2 Sampling and conditioning .32
5.17.3 Test method .33
5.17.4 Test report .33
5.18 Determination of resistance to water for whole footwear: Trough test .33
5.18.1 Principle .33
5.18.2 Test equipment .33
5.18.3 Sampling and conditioning .34
5.18.4 Test method .34
5.18.5 Test report .34
5.19 Dynamic footwear water penetration test .35
5.19.1 Principle .35
5.19.2 Equipment .35
5.19.3 Sampling and conditioning .35
5.19.4 Test method .35
5.19.5 Test report .37
5.20 Determination of impact resistance of a metatarsal protection .37
5.20.1 Test equipment .37
5.20.2 Sampling and conditioning .39
5.20.3 Test method .39
5.20.4 Test report .41
5.21 Determination of the dimension of the ankle protection .41
5.21.1 Sampling and conditioning .41
5.21.2 Test method .41
iv © ISO 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 20344:2020
ISO/DIS 20344:2020(E)
5.21.3 Test report .42
5.22 Determination of the shock absorption capacity of ankle protection materials
incorporated into the upper .42
5.22.1 Principle .42
5.22.2 Test equipment .42
5.22.3 Sampling and conditioning .43
5.22.4 Test method .44
5.22.5 Test report .44
5.23 Determination of cutting resistance .44
5.23.1 Sampling and conditioning .44
5.23.2 Dimension of the cut resistant protective area .44
5.23.3 Cut resistance .45
5.23.4 Test report .45
5.24 Scuff caps .46
5.24.1 Sampling and conditioning .46
5.24.2 Test method .46
5.24.3 Test report .46
5.25 Determination of seam strength .46
5.25.1 Sampling and conditioning .46
5.25.2 Test procedure .46
5.25.3 Test report .46
6 Test methods for upper, lining and tongue .47
6.1 Determination of thickness of upper .47
6.1.1 Sampling and conditioning .47
6.1.2 Test method .47
6.1.3 Test report .47
6.2 Measurement of the height of the upper .47
6.2.1 Sampling and conditioning .47
6.2.2 Test method for the complete upper .47
6.2.3 Test method for the determination of the area for non-water vapour
permeable materials .48
6.3 Determination of tear strength of the upper, lining and/or tongue .50
6.3.1 Sampling and conditioning .50
6.3.2 Test method .50
6.3.3 Test report .51
6.4 Determination of the tensile properties of the upper material .51
6.4.1 Sampling and conditioning .51
6.4.2 Test method .51
6.4.3 Test report .52
6.5 Determination of upper flexing resistance .52
6.5.1 Sampling and conditioning .52
6.5.2 Test method .52
6.5.3 Test report .54
6.6 Determination of water vapour permeabili
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.