SIST EN 60317-27:2001
(Main)Specifications for particular types of winding wires -- Part 27: Paper tape covered rectangular copper wire
Specifications for particular types of winding wires -- Part 27: Paper tape covered rectangular copper wire
The contents of the corrigendum of April 2002 have been included in this copy.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -- Teil 27: Flachdrähte aus Kupfer, papierisoliert
Spécifications pour types particuliers de fils de bobinage -- Partie 27: Fil de section rectangulaire en cuivre recouvert de ruban papier
Cette publication remplace la CEI 182-3.
Specifications for particular types of winding wires - Part 27: Paper tape covered rectangular copper wire
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60317-27:2001
01-september-2001
Specifications for particular types of winding wires - Part 27: Paper tape covered
rectangular copper wire
Specifications for particular types of winding wires -- Part 27: Paper tape covered
rectangular copper wire
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -- Teil 27:
Flachdrähte aus Kupfer, papierisoliert
Spécifications pour types particuliers de fils de bobinage -- Partie 27: Fil de section
rectangulaire en cuivre recouvert de ruban papier
Ta slovenski standard je istoveten z: EN 60317-27:1998
ICS:
29.060.10 Žice Wires
SIST EN 60317-27:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60317-27:2001
---------------------- Page: 2 ----------------------
SIST EN 60317-27:2001
---------------------- Page: 3 ----------------------
SIST EN 60317-27:2001
---------------------- Page: 4 ----------------------
SIST EN 60317-27:2001
---------------------- Page: 5 ----------------------
SIST EN 60317-27:2001
---------------------- Page: 6 ----------------------
SIST EN 60317-27:2001
NORME
CEI
INTERNATIONALE
IEC
60317-27
INTERNATIONAL
Troisième édition
STANDARD
Third edition
1998-01
Spécifications pour types particuliers
de fils de bobinage –
Partie 27:
Fil de section rectangulaire en cuivre
recouvert de ruban papier
Specifications for particular types
of winding wires –
Part 27:
Paper tape covered rectangular copper wire
IEC 1998 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
PRICE CODE J
International Electrotechnical Commission
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 7 ----------------------
SIST EN 60317-27:2001
60317-27 © IEC:1998 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 27: Paper tape covered rectangular copper wire
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60317-27 has been prepared by IEC technical committee 55:
Winding wires.
This third edition cancels and replaces the second edition published in 1990, and amendment 1
(1993).
The text of this standard is based on the following documents :
FDIS Report on voting
55/616/FDIS 55/642/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
Annexes A and B are for information only.
The contents of the corrigendum of April 2002 have been included in this copy.
---------------------- Page: 8 ----------------------
SIST EN 60317-27:2001
60317-27 © IEC:1998 – 5 –
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 27: Paper tape covered rectangular copper wire
1 Scope
This International Standard specifies the requirements of paper tape covered rectangular
copper winding wires. This covering consists of two or more layers of paper tape, all in the
same direction and is primarily intended for winding coils for oil immersed transformers.
The range of nominal conductor dimensions covered by this standard is
– width: min. 2,0 mm max. 16,0 mm;
– thickness: min. 0,80 mm max. 5,60 mm.
The paper tapes covered by this standard are restricted to those specified in IEC 60554-1
having thicknesses in the range 25 μm to 125 μm inclusive.
When a reference is made to winding wire according to this standard, the following information
shall be given in the description:
– reference to IEC 60317-27;
– nominal conductor dimensions in millimetres (width × thickness);
– nominal increase in dimensions due to paper.
Example: IEC 60317-27 4,00 × 1,00 + 0,20
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60317. At the time of publication, the editions indicated
were valid. All normative documents are subject to revision, and parties to agreements based
on this part of IEC 60317 are encouraged to investigate the possibility of applying the most
recent editions of the normative documents indicated below. Members of the IEC and ISO
maintain registers of currently valid international standards.
IEC 60317-0-2:1990, Specifications for particular types of winding wires – Part 0: General
requirements – Section 2: Enamelled rectangular copper wire
IEC 60554-1:1977, Specification for cellulosic papers for electrical purposes – Part 1:
Definitions and general requirements
IEC 60851, Methods of test for winding wires
---------------------- Page: 9 ----------------------
SIST EN 60317-27:2001
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.