Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements for agglomerators

This document deals with all significant hazards, hazardous situations and events relevant to agglomerators for the modification of plastic scraps in its form, size and flow characteristics, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). The hazards have been identified taking into account all phases of the machine life cycle according to EN ISO 12100:2010, 5.4.
Machines considered in this document begin at the outer edge of the feed opening and end at the outer edge of the discharge opening.
This document does not deal with:
-   hazards due to emissions by processing materials that could be hazardous to health;
-   hazards caused by ignition of flammable residues in material to be processed;
-   requirements for exhaust ventilation systems.
This document is not applicable to agglomerators manufactured before the date of its publication.

Kunststoff- und Gummimaschinen - Zerkleinerungsmaschinen - Teil 4: Sicherheitsanforderungen für Agglomeratoren

Fügen Sie im 7. Absatz den ersten Spiegelstrich ein: "
-   Agglomeratoren mit pneumatisch und/oder hydraulisch bewegten Antrieben sind vom Anwendungsbereich ausgenommen."
zu lesen: "
Die wichtigsten Änderungen gegenüber der EN 12012-4:2006+A1:2008 sind:
-   Agglomeratoren mit pneumatisch und/oder hydraulisch bewegten Antrieben sind vom Anwendungsbereich ausgenommen;
-   die Revision von Type-A- und Type-B-Normen sind berücksichtigt worden;
-   die Liste der signifikanten Gefährdungen ist in einen informativen Anhang verschoben worden;
-   die Performance Level/Sicherheits-Integritäts-Level von sicherheitsbezogenen Teilen des Steuerungssystems sind nach EN ISO 13849-1:2015 / EN 62061:2005, EN 62061:2005/A1:2013, EN 62061:2005/A2:2015 festgelegt worden;
-   die Gefährdungen in Zusammenhang mit dem Herausschleudern von Teilen oder Materialien aus der Agglomeratorkammer sind herausgenommen worden, weil zuverlässige und gut konstruierte Kammern jetzt den Stand der Technik darstellen (es ist lange nicht mehr über den Bruch einer Kammer berichtet worden);
-   Beschickungsöffnungen mit großen Abmessungen sind berücksichtigt;
-   Anforderungen für bewegliche Teile des Austragssystems sind ergänzt;
-   der Anhang zur Lärmmessung ist überarbeitet worden."

Machines pour les matières plastiques et le caoutchouc - Machines à fragmenter - Partie 4 : Prescriptions de sécurité relatives aux agglomérateurs

Ajouter le premier tiret suivant au 7ème alinéa : "
-   la suppression du domaine d’application des agglomérateurs dont les organes de service sont actionnés par de l'énergie pneumatique et/ou hydraulique ;"
pour lire : "
Par rapport à l’EN 12012-4:2006+A1:2008, les principales modifications concernent :
-   la suppression du domaine d’application des agglomérateurs dont les organes de service sont actionnés par de l'énergie pneumatique et/ou hydraulique ;
-   la prise en compte de la révision des normes de type A et de type B ;
-   le transfert de la liste des phénomènes dangereux en annexe informative ;
-   la spécification des niveaux de performances/des niveaux d'intégrité de sécurité des parties des systèmes de commande liées à la sécurité, suivant l'EN ISO 13849 1:2015 / l'EN 62061:2005, l'EN 62061:2005/A1:2013, l'EN 62061:2005/A2:2015 ;
-   la suppression des risques liés à l'éjection de pièces ou de matière de la chambre d'agglomération car des chambres fiables et bien conçues représentent maintenant l'état de l'art (aucune projection et aucune chambre cassée n'ont été signalées depuis longtemps) ;
-   la prise en compte des ouvertures d'alimentation de grandes dimensions ;
-   l’adjonction des exigences des parties mobiles des systèmes d'évacuation ;
-   la révision de l'annexe sur le mesurage du bruit.".

Stroji za predelavo gume in plastike - Drobilni stroji - 4. del: Varnostne zahteve za aglomeratorje

General Information

Status
Not Published
Public Enquiry End Date
30-May-2021
Technical Committee
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
07-Apr-2021
Due Date
25-Aug-2021
Completion Date
11-May-2021

Relations

Buy Standard

Draft
EN 12012-4:2019/oprA1:2021
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12012-4:2019/oprA1:2021
01-maj-2021
Stroji za predelavo gume in plastike - Drobilni stroji - 4. del: Varnostne zahteve za
aglomeratorje
Plastics and rubber machines - Size reduction machines - Part 4: Safety requirements
for agglomerators
Kunststoff- und Gummimaschinen - Zerkleinerungsmaschinen - Teil 4:
Sicherheitsanforderungen für Agglomeratoren
Machines pour les matières plastiques et le caoutchouc - Machines à fragmenter - Partie
4 : Prescriptions de sécurité relatives aux agglomérateurs
Ta slovenski standard je istoveten z: EN 12012-4:2019/prA1
ICS:
83.200 Oprema za gumarsko Equipment for the rubber and
industrijo in industrijo plastics industries
polimernih materialov
SIST EN 12012-4:2019/oprA1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 12012-4:2019/oprA1:2021

---------------------- Page: 2 ----------------------
SIST EN 12012-4:2019/oprA1:2021


DRAFT
EUROPEAN STANDARD
EN 12012-4:2019
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
April 2021
ICS 83.200
English Version

Plastics and rubber machines - Size reduction machines -
Part 4: Safety requirements for agglomerators
Machines pour les matières plastiques et le caoutchouc Kunststoff- und Gummimaschinen -
- Machines à fragmenter - Partie 4 : Prescriptions de Zerkleinerungsmaschinen - Teil 4:
sécurité relatives aux agglomérateurs Sicherheitsanforderungen für Agglomeratoren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 145.

This draft amendment A1, if approved, will modify the European Standard EN 12012-4:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12012-4:2019/prA1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 12012-4:2019/oprA1:2021
EN 12012-4:2019/prA1:2021 (E)
Contents Page
European foreword . 3
1 Modification to European foreword . 4
2 Modification to the Scope . 4
3 Modification to Clause 2, Normative references . 5
4 Modification to 4.2.1, Access through openings in the agglomerator chamber . 5
5 Modification to 4.2.3, Moving parts of discharge systems . 6
6 Modification to 4.6.1.3, Protection against direct contact. 6
7 Modification to 4.6.1.4, Protection against indirect contact . 7
8 Modification to 4.7.2, Stop function . 7
9 Modification to 4.7.3, Start function . 7
10 Modification to subclause 6.2.1 . 7
11 Modification to 6.3.2, Warning signs . 7
12 Modification to Annex ZA, Relationship between this European Standard and the
essential requirements of Directive 2006/42/EC aimed to be covered . 8

2

---------------------- Page: 4 ----------------------
SIST EN 12012-4:2019/oprA1:2021
EN 12012-4:2019/prA1:2021 (E)
European foreword
This document (EN 12012-4:2019/prA1:2021) has been prepared by Technical Committee CEN/TC 145
“Plastics and rubber machines”, the secretariat of which is held by UNI.
This document is currently submitted to the CEN Enquiry.
This document is an Amendment to EN 12012-4:2019.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
In comparison with the previous edition, the following technical and editorial modifications have been
made:
— European Foreword: dash added;
— Scope: editorial modification and dash added;
— Normative references: a reference date updated;
— 4.2.1: updated normative references;
— 4.2.3: updated normative reference;
— 4.6.1.3: modified text;
— 4.6.1.4: modified text;
— 4.7.2: modified text;
— 4.7.3: updated normative reference;
— 6.2.1: modified text;
— 6.3.2: modified text;
— Table Annex ZA: modified text.

3

---------------------- Page: 5 ----------------------
SIST EN 12012-4:2019/oprA1:2021
EN 12012-4:2019/prA1:2021 (E)
1 Modification to the European foreword
th
Add the first dash to the 7 paragraph: "
—  the agglomerators with actuators moved by pneumatic and/or hydraulic energy have been excluded
from the Scope;"
to read: "
The main changes compared to the EN 12012-4:2006+A1:2008 are:
— the agglomerators with actuators moved by pneumatic and/or hydraulic energy have been excluded
from the Scope;
— the revision of type-A and type-B standards have been considered;
— the list of significant hazards has been moved to an informative annex;
— the performance levels/safety integrity levels of safety related parts of control systems have been
specified in accordance with EN ISO 13849-1:2015 / EN 62061:2005, EN 62061:2005/A1:2013,
EN 62061:2005/A2:2015;
— the hazards related to the ejection of parts or materials from the agglomerator chamber have been
removed because reliable and well-designed chambers represent now the state of the art (no
projections and no broken chamber have been reported for a long time);
— feed openings of big dimensions are considered;
— requirements for moving parts of discharge systems are added;
— the annex for noise measurement has been revised.".
2 Modification to the Scope
In the third paragraph, third dash, make editorial modification and add an additional last dash: "
—  agglomerators moved by pneumatic and/or hydraulic energy."
to read: "
This document deals with all significant hazards, hazardous situations and events relevant to
agglomerators for the modification of plastic scraps in its form, size and flow characteristics, when they
are used as intended and under conditions of misuse which are reasonably foreseeable by the
manufacturer (see Annex A). The hazards have been identified taking into account all phases of the
machine life cycle according to EN ISO 12100:2010, 5.4.
Machines considered in this document begin at the outer edge of the feed opening and end at the outer
edge of the discharge opening.
This document does not deal with:
— hazards due to emissions by processing materials that could be hazardous to health;
— hazards caused by ignition of flammable residues in material to be processed;
— requirements for exhaust ventilation systems;
 agglomerators moved by pneumatic and/or hydraulic energy.
4

---------------------- Page: 6 ----------------------
SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.