SIST EN 60684-3-209:2010

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded (IEC 60684-3-209:2010)

This part of IEC 60684 gives the requirements for two types of general purpose, flexible, flame retarded, heat-shrinkable polyolefin sleeving. This sleeving has been found suitable for use at temperatures up to 125 °C. - Type A - Highly flame retarded - Type B - Flame retarded The minimum supplied and maximum recovered internal diameters shall be specified by the manufacturer and shall meet the minimum wall thicknesses given in Table 2. It is normally available in bore sizes up to 75 mm as supplied and in the following colours: black, brown, white, red, yellow, green, blue, orange, violet, grey and yellow/green. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 209: Polyolefin-Wärmeschrumpfschläuche, Standardtyp, flammwidrig (IEC 60684-3-209:2010)

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 209: Gaines thermorétractables, en polyoléfine, d'utilisation générale, ignifugées (CEI 60684-3-209:2010)

La CEI 60684-3-209:2010 donne les exigences pour deux types de gaines souples, thermorétractables, en polyoléfine, ignifugées d'utilisation générale. Ces gaines se sont révélées être adaptées à une utilisation à des températures jusqu'à 125 °C.  - Type A - Hautement ignifugé  - Type B - Ignifugé  Cette édition a été alignée sur la UL 224 pour tuyaux souples thermorétractables à 125 °C en polyoléfine.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 209. list: Toplotno skrčljive poliolefinske cevi za splošne namene, ognjevarne (IEC 60684-3-209:2010)

Ta del IEC 60684 podaja zahteve za dva tipa gibkih, ognjevarnih ter toplotno krčljivih poliolefinskih cevi za splošne namene. Za to cev je bilo ugotovljeno, da je primerna za uporabo pri temperaturah do 125 °C. – Tip A – Visoko ognjevarna – Tip B – Ognjevarna. Minimalne predložene in maksimalne zajete notranje premere bo določil proizvajalec; le-ti bodo ustrezali minimalni debelini stene, podani v Razpredelnici 2. Običajno je na voljo z velikostjo odprte cevi do 75 mm in v naslednjih barvah:  črna, rjava, bela, rdeča, rumena, zelena, modra, oranžna, vijoličasta, siva in rumeno/zelena. Materiali, skladni s to specifikacijo, ustrezajo vzpostavljenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati na podlagi dejanskih zahtev za ustrezno delovanje pri takšni uporabi, in ne le na podlagi same specifikacije.

General Information

• Status: Published
• Publication Date: 22-Jul-2010
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 14-Jul-2010
• Due Date: 18-Sep-2010
• Completion Date: 23-Jul-2010
• Ref Project: EN 60684-3-209:2010 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded

Relations

• Replaces: SIST EN 60684-3-209:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded, shrink ratio 2:1
• Effective Date: 28-Jan-2023
• Replaces: SIST EN 60684-3-209:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded, shrink ratio 2:1
• Effective Date: 01-Jul-2013
• Replaces: SIST EN 60684-3-209:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded, shrink ratio 2:1
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60684-3-209:2010
01-september-2010
1DGRPHãþD
SIST EN 60684-3-209:2004
*LENHL]RODFLMVNHFHYLGHO6SHFLILNDFLMH]DSRVDPH]QHWLSHFHYLOLVW
7RSORWQRVNUþOMLYHSROLROHILQVNHFHYL]DVSORãQHQDPHQHRJQMHYDUQH,(&

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
209: Heat-shrinkable polyolefin sleeving, general purpose, flame retarded (IEC 60684-3-
209:2010)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 209:
Polyolefin-Wärmeschrumpfschläuche, Standardtyp, flammwidrig (IEC 60684-3-209:2010)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 209: Gaines thermorétractables, en polyoléfine, d'utilisation générale, ignifugées
(CEI 60684-3-209:2010)
Ta slovenski standard je istoveten z: EN 60684-3-209:2010
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST EN 60684-3-209:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60684-3-209:2010

---------------------- Page: 2 ----------------------

SIST EN 60684-3-209:2010

EUROPEAN STANDARD
EN 60684-3-209

NORME EUROPÉENNE
July 2010
EUROPÄISCHE NORM

ICS 29.035.20 Supersedes EN 60684-3-209:2003


English version


Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 209: Heat-shrinkable polyolefin sleeving, general purpose, flame
retarded
(IEC 60684-3-209:2010)


Gaines isolantes souples -  Isolierschläuche -
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines - Schlauchtypen -
Feuille 209: Gaines thermorétractables, Blatt 209: Polyolefin-
en polyoléfine, d'utilisation générale, Wärmeschrumpfschläuche, Standardtyp,
ignifugées flammwidrig
(CEI 60684-3-209:2010) (IEC 60684-3-209:2010)




This European Standard was approved by CENELEC on 2010-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-209:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60684-3-209:2010
EN 60684-3-209:2010 - 2 -
Foreword
The text of document 15/561/FDIS, future edition 3 of IEC 60684-3-209, prepared by IEC TC 15, Solid
electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 60684-3-209 on 2010-07-01.
This European Standard supersedes EN 60684-3-209:2003.
This EN 60684-3-209:2010 has been aligned with UL 224 for 125 °C flexible heat-shrinkable polyolefin
tubing.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-07-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-209:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60684-3-209:2010
- 3 - EN 60684-3-209:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60684-1 2003 Flexible insulating sleeving - EN 60684-1 2003
Part 1: Definitions and general requirements


IEC 60684-2 1997 Flexible insulating sleeving - EN 60684-2 1997
+ A1 2003 Part 2: Methods of test + A1 2003
+ A2 2005 + A2 2005


IEC 60757 1983 Code for designation of colours HD 457 S1 1985

---------------------- Page: 5 ----------------------

SIST EN 60684-3-209:2010

---------------------- Page: 6 ----------------------

SIST EN 60684-3-209:2010
IEC 60684-3-209
®
Edition 3.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Flexible insulating sleeving –
Part 3: Specifications for individual types of sleeving –
Sheet 209: Heat-shrinkable, polyolefin sleeving, general purpose, flame retarded

Gaines isolantes souples –
Partie 3: Spécifications pour types particuliers de gaines –
Feuille 209: Gaines thermorétractables, en polyoléfine, d’utilisation générale,
ignifugées


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.035.20 ISBN 978-2-88910-965-4
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60684-3-209:2010
– 2 – 60684-3-209 © IEC:2010
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Designation .6
4 Conditions of test.7
5 Requirements .7
6 Sleeving conformance.7

Table 1 – Required test samples .7
Table 2 – Minimum recovered wall thicknesses for maximum recovered internal
diameters.7
Table 3 – Property requirements .8
Table 4 – Mandrel diameters for heat shock and low temperature bending.9

---------------------- Page: 8 ----------------------

SIST EN 60684-3-209:2010
60684-3-209 © IEC:2010 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 209: Heat-shrinkable, polyolefin sleeving,
general purpose, flame retarded


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is a
...