SIST EN 60684-3-284:2015

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 284: Heat-shrinkable, sleevings, for oil barrier applications

IEC 60684-3-284:2014 gives the requirements for heat-shrinkable sleevings for oil barrier, medium voltage cable jointing and termination applications, with nominal shrink ratios of up to 3:1. These sleevings have been found suitable for use up to temperatures of 80 °C. Included are Type A: polyolefin based and Type B: fluoropolymer based, enhanced oil resistance. These sleevings are normally supplied as translucent. Since these types of sleevings cover a significantly large range of sizes and wall thicknesses, Annex A, Tables A.1 and A.2, in this document, provide a guide to the range of sizes available. The actual size will be agreed between the purchaser and supplier. Materials which conform to this standard meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this standard alone. This sleeving is designed to be used in MV cable accessories and as such, electrical performance as defined as part of the assembly. Examples of this are described in HD 629 and IEC 60502 series.
Keywords: heat-shrinkable sleevings, oil barrier, medium voltage cable jointing, termination applications

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 284: Wärmeschrumpfschläuche mit ölsperrenden Eigenschaften

Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines - Feuille 284: Gaines thermorétractables pour applications de barrière résistant à l'huile

L'IEC 60684-3-284:2014 fournit les exigences relatives aux gaines thermorétractables pour applications de jonction et de terminaison de câble moyenne tension avec barrière résistant à l'huile, possédant des rapports de rétr-eint nominaux jusqu'à 3:1. Ces gaines se sont révélées être adaptées à une utilisation à des températures allant jusqu'à 80 °C Type A; à base de polyoléfine. Type B; à base de fluoropolymère, résistance améliorée à l'huile. Ces gaines sont normalement fournies en matériau translucide. Comme ces types de gaines couvrent une gamme très large de dimensions et d'épaisseurs de paroi, l'Annexe A, les Tableaux A.1 et A.2, du présent document fournissent des lignes directrices sur la gamme des dimensions disponibles. La dimension réelle fera l'objet d'un accord entre l'acheteur et le fournisseur. Les matériaux conformes à la présente norme satisfont à des niveaux de performance établis. Cependant, il convient que le choix d'un matériau par un utilisateur pour une application particulière soit fondé sur les exigences réelles nécessaires pour obtenir les performances satisfaisantes pour cette application, et qu'il ne soit pas fondé uniquement sur la présente norme. Ces gaines sont conçues pour être utilisées dans des accessoires de câbles moyenne tension et, en conséquence, les performances électriques sont définies dans le cadre de l'assemblage concerné. De tels exemples sont décrits dans le HD 629 et l'IE applications de jonction et de terminaison de câble moyenne tension C 60502.
Mots clés: Gaines thermorétractables, barrière résistant à l'huile, de terminaison de câble moyenne tension applications

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne vrste cevi - 284. list: Toplotno skrčljive cevi za oljne pregrade

Ta del standarda IEC 60684 določa zahteve za toplotno skrčljive cevi za oljne pregrade, srednjenapetostne kabelske spoje in zaključke, z nazivnimi razmerji krčenja do 3:1. Te cevi so primerne za uporabo pri temperaturah do 80 °C.
Tip A: na poliolefinski podlagi.
Tip B: na fluoropolimerni podlagi, boljša odpornost proti olju.
Te cevi se običajno dobavljajo prosojne.
Ker ta tipa cevi zajemata bistveno velik razpon velikosti in debelin sten, so v tabelah A.1 in A.2 v dodatku A tega dokumenta zagotovljena navodila glede razpona razpoložljivih velikosti. O dejanski velikosti se dogovorita kupec in dobavitelj.
Materiali, ki so skladni s tem standardom, ustrezajo določenim ravnem delovanja. Vendar mora uporabnik material za določeno uporabo izbrati glede na dejanske zahteve, ki omogočajo ustrezno delovanje pri tej uporabi, in ne samo na podlagi tega standarda. Ta cev je zasnovana za uporabo s srednjenapetostnimi kabli, kot taka pa tudi električna zmogljivost, kot je določena kot del sestava. Primeri so opisani v skupini standardov HD 629 in IEC 60502.

General Information

• Status: Published
• Publication Date: 13-Aug-2015
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IIZS - Insulating materials and systems
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 11-Feb-2015
• Due Date: 18-Apr-2015
• Completion Date: 14-Aug-2015
• Ref Project: EN 60684-3-284:2014 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 284: Heat-shrinkable sleevings, for oil barrier applications

Overview

EN 60684-3-284:2014 (IEC 60684-3-284:2014) specifies requirements for heat-shrinkable sleevings for oil barrier use in medium voltage (MV) cable jointing and termination applications. The sheet covers heat‑shrinkable sleeving with nominal shrink ratios up to 3:1, suitable for service temperatures up to 80 °C, and normally supplied translucent. Two material types are defined:

• Type A - polyolefin-based
• Type B - fluoropolymer-based (enhanced oil resistance)

The standard is part of the IEC 60684 series and should be applied together with the general definitions and test methods given in IEC 60684‑1 and IEC 60684‑2.

Key topics and requirements

The document sets out technical requirements and test conditions that ensure predictable performance of oil‑barrier heat‑shrinkable sleeving. Key topics include:

• Material types and intended use: differentiation of Type A and Type B based on polymer chemistry and oil resistance.
• Shrink ratio and sizing: nominal shrink ratios up to 3:1; Annex A (Tables A.1, A.2) provides a guide to typical expanded/recovered sizes and wall thicknesses; exact sizes agreed between purchaser and supplier.
• Pre-test shrink conditions: forced‑air oven shrink prior to testing - 175 °C ±3 K for Type A and 200 °C ±3 K for Type B for 10 ±1 minutes.
• Mechanical and thermal tests: longitudinal change, heat shock, tensile strength, elongation at break, secant modulus, dimensional stability, and bending at low temperature.
• Electrical and ageing tests: breakdown voltage, volume resistivity, heat ageing and long‑term heat ageing (conditions described in the standard), and resistance to selected fluids (oil compatibility).
• Conformance and labelling: designation format for packaging and guidance on testing a typical size to represent a batch.

Applications and users

This standard is intended for:

• Manufacturers of heat‑shrinkable sleevings and MV cable accessory components.
• Cable accessory designers and specifiers working on medium voltage cable jointing and termination where an oil‑barrier sleeve is required.
• Procurement and quality teams needing material and test acceptance criteria.
• Test laboratories performing conformance testing per IEC 60684‑2 methods.

Practical applications include oil‑barrier layers in MV cable terminations and joints where enhanced oil resistance and reliable shrink performance are required. Note: electrical performance of the complete MV accessory is determined at the assembly level (see HD 629, IEC 60502 series).

Related standards

• IEC 60684‑1 - Definitions and general requirements
• IEC 60684‑2 - Methods of test
• HD 629 - MV cable accessory assessment (example)
• IEC 60502 series - Power cables and accessories
• IEC 60296, IEC 60055‑2 - referenced for fluid and cable construction context

Keywords: heat-shrinkable sleevings, oil barrier, medium voltage cable jointing, termination applications, Type A polyolefin, Type B fluoropolymer, IEC 60684-3-284:2014.

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2015
*LENHL]RODFLMVNHFHYLGHO6SHFLILNDFLMH]DSRVDPH]QHYUVWHFHYLOLVW
7RSORWQRVNUþOMLYHFHYL]DROMQHSUHJUDGH
Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet
284: Heat-shrinkable, sleevings, for oil barrier applications
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 284:
Wärmeschrumpfschläuche mit ölsperrenden Eigenschaften
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines -
Feuille 284: Gaines thermorétractables pour applications de barrière résistant à l'huile
Ta slovenski standard je istoveten z: EN 60684-3-284:2014
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60684-3-284

NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2014
ICS 29.035.20
English Version
Flexible insulating sleeving - Part 3: Specifications for individual
types of sleeving - Sheet 284: Heat-shrinkable, sleevings, for oil
barrier applications
(IEC 60684-3-284:2014)
Gaines isolantes souples - Partie 3: Spécifications pour Isolierschläuche - Teil 3: Anforderungen für einzelne
types particuliers de gaines - Feuille 284: Gaines Schlauchtypen - Blatt 284: Wärmeschrumpfschläuche mit
thermorétractables pour applications de barrière résistant à ölsperrenden Eigenschaften
l'huile (IEC 60684-3-284:2014)
(CEI 60684-3-284:2014)
This European Standard was approved by CENELEC on 2014-11-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60684-3-284:2014 E

Foreword
The text of document 15/693/CDV, future edition 1 of IEC 60684-3-284, prepared by IEC/TC 15 "Solid
electrical insulating materials" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60684-3-284:2014.
The following dates are fixed:
(dop) 2015-08-27
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2017-11-27
• latest date by which the national standards conflicting with
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60684-3-284:2014 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60684-3 (all sheets) NOTE Harmonized as EN 60684-3 (all sheets) (not modified).
IEC 60757:1983 NOTE Harmonized as HD 457 S1:1985 (not modified).

- 3 - EN 60684-3-284:2014
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is
available here: www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60055-2 -  Paper-insulated metal-sheathed cables for - -
rated voltages up to 18/30 kV (with copper
or aluminium conductors and excluding
gas-pressure and oil-filled cables -
Part 2: General and construction
requirements
IEC 60296 -  Fluids for electrotechnical applications - EN 60296 -
Unused mineral insulating oils for
transformers and switchgear
IEC 60684-1 2003 Flexible insulating sleeving - EN 60684-1 2003
Part 1: Definitions and general
requirements
IEC 60684-2 2011 Flexible insulating sleeving - EN 60684-2 2011
Part 2: Methods of test
IEC 60684-3-284 ®
Edition 1.0 2014-10
INTERNATIONAL
STANDARD
Flexible insulating sleeving –

Part 3: Specifications for individual types of sleeving –

Sheet 284: Heat-shrinkable sleevings, for oil barrier applications

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
M
ICS 29.035.20 ISBN 978-2-8322-1891-4

– 2 – IEC 60684-3-284:2014 © IEC 2014
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Designation . 7
4 Conditions of test . 7
5 Requirements . 7
6 Sleeving conformance . 7
Annex A (informative) Guide to the typical sizes and wall thicknesses . 11
Bibliography . 12

Table 1 – Property requirements for Type A . 7
Table 2 – Property requirements for Type B . 9
Table 3 – Requirements for breakdown voltage, Types A and B . 10
Table 4 – Resistance to selected fluids . 10
Table A.1 – Dimensions Type A . 11
Table A.2 – Dimensions Type B . 11

IEC 60684-3-284:2014 © IEC 2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 284: Heat-shrinkable sleevings, for oil barrier applications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses ari
...