SIST EN 10218-1:2012
(Main)Steel wire and wire products - General - Part 1: Test methods
Steel wire and wire products - General - Part 1: Test methods
This part of EN 10218 specifies the methods for the general testing of steel wire and wire products which have been cold worked, annealed or oil hardened and tempered and/or coated and are of constant cross section, either round, or special section. It includes tensile testing, torsion testing, reverse bend testing, wrapping test, bend test, reverse torsion test, compression test, deep etch test, hardness test, quench hardenability test, fatigue test, wire cast measurement, artificial ageing, decarburization test, non-destructive tests, grain size tests, segregation test, non-metallic inclusion test and chemical analysis.
Stahldraht und Drahterzeugnisse - Allgemeines - Teil 1: Prüfverfahren
Diese Europäische Norm legt die Verfahren fest für die allge¬meine Prüfung von Stahldraht und Drahterzeugnissen, die kalt umge¬formt, geglüht oder ölschlussvergütet und/oder umhüllt sind und einen gleichbleibenden Querschnitt entweder runder oder spezieller Form aufweisen. Er gilt für den Zugversuch, den Verwindeversuch, den Hin und Herbiegeversuch, den Wickelver¬such, den Biegeversuch, den Wechselverwin-deversuch, den Stauch¬versuch, den Tiefätzversuch, die Härteprü¬fung, die Ab¬schreck¬härtbarkeitsprüfung, den Dauer¬schwingversuch, Messung des Drahtschlages, die künstli¬che Alte¬rung, die Entkohlungsprüfung, zerstörungsfreie Prüfverfahren, die Korn¬größenprüfung, die Seige¬rungsprüfung, die Prüfung auf nicht¬metal-lische Einschlüsse und die chemische Analy¬se.
Fils et produits tréfilés en acier - Généralités - Partie 1: Méthodes d'essai
La présente norme européenne spécifie des méthodes générales d’essai des fils et produits tréfilés en aciers écrouis, recuits, trempés à l’huile et revenus et/ou revêtus, de section constante, circulaire ou spéciale. Elle concerne les essais de traction, de torsion simple, de pliage alterné, d’enroulement, de pliage simple, de torsion alternée, de compression, d’attaque chimique profonde, de dureté, de durcissement par trempabilité, de fatigue, de mesure des plés de tréfilage, de vieillissement artificiel, de décarburation, de contrôle non destructif, de mesure de la grosseur de grain, de ségrégation, de détermination de la teneur en inclusions non métalliques et d’analyse chimique.
Jeklena žica in žični izdelki - Splošno - 1. del: Preskusne metode
Ta evropski standard določa metode za splošno preskušanje jeklene žice in žičnih izdelkov, ki so bili hladno obdelani, žarjeni ali kaljeni v olju ter popuščeni in/ali prevlečeni ter imajo konstanten prečni prerez (okrogel ali poseben). Zajema natezne preskuse, vzvojne preskuse, preskuse z izmeničnim upogibanjem, preskuse z navijanjem, izmenične vzvojne preskuse, tlačne preskuse, preskuse kaljivosti,preskuse utrujenosti, merjenje odlitka žice, umetno staranje, preskuse razogljičenja, neporušitvene preskuse, preskuse velikosti zrn, preskuse odvojitve, preskuse nekovinskih vključkov in kemično analizo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.HStahldraht und Drahterzeugnisse - Allgemeines - Teil 1: PrüfverfahrenFils et produits tréfilés en acier - Généralités - Partie 1: Méthodes d'essaiSteel wire and wire products - General - Part 1: Test methods77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chainsICS:Ta slovenski standard je istoveten z:EN 10218-1:2012SIST EN 10218-1:2012en,fr,de01-marec-2012SIST EN 10218-1:2012SLOVENSKI
STANDARDSIST EN 10218-1:19971DGRPHãþD
SIST EN 10218-1:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10218-1
January 2012 ICS 77.140.65 Supersedes EN 10218-1:1994English Version
Steel wire and wire products - General - Part 1: Test methods
Fils et produits tréfilés en acier - Généralités - Partie 1 : Méthodes d'essai
Stahldraht und Drahterzeugnisse - Allgemeines - Teil 1: Prüfverfahren This European Standard was approved by CEN on 3 September 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10218-1:2012: ESIST EN 10218-1:2012
EN 10218-1:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Tensile test .53.1 General .53.2 Type of samples .53.3 Preparation of test piece .53.4 Cross-sectional area .53.5 Method of gripping .53.6 Tensile test on knotted wire .54 Simple torsion test.55 Reverse bend test .56 Wrapping test .67 Bend test .68 Reverse torsion test .69 Compression test.69.1 Purpose .69.2 Principle .610 Deep etch test .610.1 Purpose .610.2 Principle .611 Hardness test .712 Quench hardenability test .713 Fatigue test (bend and axial) .714 Wire cast measurement .714.1 General .714.2 Circular cast .814.3 Helix cast .914.3.1 General .914.3.2 Method A .914.3.3 Method B .914.4 Spiral cast . 1015 Artificial ageing . 1116 Decarburization test . 1117 Non-destructive tests . 1118 Grain size test . 1119 Segregation test . 1120 Non-metallic inclusion test . 1121 Chemical analysis . 1122 Retests . 11 SIST EN 10218-1:2012
EN 10218-1:2012 (E) 3 Foreword This document (EN 10218-1:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10218-1:1994. The standard will comprise the following parts: Part 1: Test methods; Part 2: Wire dimensions and tolerances. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10218-1:2012
EN 10218-1:2012 (E) 4 1 Scope This European Standard specifies the methods for the general testing of steel wire and wire products which have been cold worked, annealed or oil hardened and tempered and/or coated and are of constant cross section, either round, or special section. It includes tensile testing, torsion testing, reverse bend testing, wrapping test, bend test, reverse torsion test, compression test, deep etch test, hardness test, quench hardenability test, fatigue test, wire cast measurement, artificial ageing, decarburization test, non-destructive tests, grain size tests, segregation test, non-metallic inclusion test and chemical analysis. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10247, Micrographic examination of the non-metallic inclusion content of steels using standard pictures CEN/TR 10261, Iron and steel — Review of available methods of chemical analysis EN ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 643, Steels — Micrographic determination of the apparent grain size (ISO 643:2003) EN ISO 3887, Steels — Determination of depth of decarburization (ISO 3887:2003) EN ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1:2005) EN ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-1:2005) EN ISO 6508-2, Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-2:2005) EN ISO 6508-3, Metallic materials — Rockwell hardness test — Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T) (ISO 6508-3:2005) EN ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature EN ISO 6892-2, Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature EN ISO 16120-1, Non-alloy steel wire rod for conversion to wire — Part 1: General requirements ISO 7800, Metallic materials — Wire — Simple torsion tes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.