SIST EN ISO 25197:2020/A1:2023
(Amendment)Small craft - Electrical/electronic control systems for steering, shift and throttle - Amendment 1 (ISO 25197:2020/Amd 1:2022)
Small craft - Electrical/electronic control systems for steering, shift and throttle - Amendment 1 (ISO 25197:2020/Amd 1:2022)
This document establishes the requirements for the design, construction and testing of electrical/electronic steering, shift and throttle systems and dynamic positioning control systems, or combinations thereof, on small craft of up to 24 m length of hull.
This document does not apply to electric trolling motors and autopilot systems on sailing craft.
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung, Schaltung und Antrieb - Änderung 1 (ISO 25197:2020/Amd 1:2022)
Dieses Dokument legt die Anforderungen für den Entwurf, die Ausführung und die Prüfung von elektrischen/elektronischen Systemen für die Steuerung, Getriebeschaltung und die Drehzahlregelung, sowie von dynamischen Positionskontrollsystemen oder Kombinationen davon auf kleinen Wasserfahrzeugen mit einer Rumpflänge bis 24 m fest.
Dieses Dokument gilt nicht für elektrische Außenbordmotoren und Schiffs-Voraus-Steuerungssysteme auf Segelfahrzeugen.
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des gaz - Amendement 1 (ISO 25197:2020/Amd 1:2022)
Le présent document établit les exigences relatives à la conception, la construction et les essais des systèmes électriques/électroniques de contrôle de la direction, de commandes d'inverseur, des gaz et de positionnement dynamique, ou de leur combinaison, sur les petits navires d'une longueur de coque inférieure ou égale à 24 m.
Le présent document ne s'applique pas aux moteurs électriques de pêche à la traîne et aux pilotes automatiques installés sur les voiliers.
Mala plovila - Električni/elektronski regulacijski sistem za krmarjenje, prestavljanje in pogon - Dopolnilo A1 (ISO 25197:2020/Amd 1:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 25197:2020/A1:2023
01-januar-2023
Mala plovila - Električni/elektronski regulacijski sistem za krmarjenje, prestavljanje
in pogon - Dopolnilo A1 (ISO 25197:2020/Amd 1:2022)
Small craft - Electrical/electronic control systems for steering, shift and throttle -
Amendment 1 (ISO 25197:2020/Amd 1:2022)
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung,
Schaltung und Antrieb - Änderung 1 (ISO 25197:2020/Amd 1:2022)
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de
l'inverseur et des gaz - Amendement 1 (ISO 25197:2020/Amd 1:2022)
Ta slovenski standard je istoveten z: EN ISO 25197:2020/A1:2022
ICS:
47.020.60 Električna oprema ladij in Electrical equipment of ships
konstrukcij na morju and of marine structures
47.080 Čolni Small craft
SIST EN ISO 25197:2020/A1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25197:2020/A1:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 25197:2020/A1:2023
EN ISO 25197:2020/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 47.080
English Version
Small craft - Electrical/electronic control systems for
steering, shift and throttle - Amendment 1 (ISO
25197:2020/Amd 1:2022)
Petits navires - Systèmes électriques/électroniques Kleine Wasserfahrzeuge - Elektrische/elektronische
pour le contrôle de la direction, de l'inverseur et des Regelungssysteme für Steuerung, Schaltung und
gaz - Amendement 1 (ISO 25197:2020/Amd 1:2022) Antrieb - Änderung 1 (ISO 25197:2020/Amd 1:2022)
This amendment A1 modifies the European Standard EN ISO 25197:2020; it was approved by CEN on 2 August 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25197:2020/A1:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 25197:2020/A1:2023
EN ISO 25197:2020/A1:2022 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 25197:2020/A1:2023
EN ISO 25197:2020/A1:2022 (E)
European foreword
This document (EN ISO 25197:2020/A1:2022) has been prepared by Technical Committee ISO/TC 188
"Small craft" in collaboration with Technical Committee CEN/TC 464 “Small Craft” the secretariat of
which is held by SIS.
This Amendment to the European Standard EN ISO 25197:2020 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by May 2023, and
conflicting national standards shall be withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 25197:2020/Amd 1:2022 has been approved by CEN as EN ISO 25197:2020/A1:2022
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 25197:2020/A1:2023
EN ISO 25197:2020/A1:2022 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and
Annex I of Directive 2013/53/EU
Essential Clause(s)/sub- Remarks/Notes
Requirements of clause(s) of this EN
Directive 2013/53/EU
Annex I, sub clause 2.5 4.11, 12 These clauses specify the information to be
included in the owner’s manual.
Owner’s manual
Annex I, 5.4 Steering 10.2 In respect of transmission of steering loads in all
system foreseeable conditions.
5.4.1 General
Annex I, 5.4 Steering 9.1.4 In respect of single engine non-sailing craft with
system remote rudder steering only.
5.4.2 Emergency
arrangements
Annex II(3) - Steering 10.2 In respect of the transmission of steering loads in
wheels, steering for electric/electronic steering systems supplied
mechanisms and as components only.
cable assemblies
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the
...
SLOVENSKI STANDARD
SIST EN ISO 25197:2020/oprA1:2022
01-april-2022
Mala plovila - Električni/elektronski regulacijski sistem za krmarjenje, prestavljanje
in pogon - Dopolnilo A1 (ISO 25197:2020/DAM 1:2022)
Small craft - Electrical/electronic control systems for steering, shift and throttle -
Amendment 1 (ISO 25197:2020/DAM 1:2022)
Kleine Wasserfahrzeuge – Elektrische/elektronische Regelungssysteme für Steuerung,
Schaltung und Antrieb – Änderung 1 (ISO 25197:2020/DAM 1:2022)
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de
l'inverseur et des gaz - Amendement 1 (ISO 25197:2020/DAM 1:2022)
Ta slovenski standard je istoveten z: EN ISO 25197:2020/prA1
ICS:
47.020.60 Električna oprema ladij in Electrical equipment of ships
konstrukcij na morju and of marine structures
47.080 Čolni Small craft
SIST EN ISO 25197:2020/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25197:2020/oprA1:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 25197:2020/oprA1:2022
DRAFT AMENDMENT
ISO 25197:2020/DAM 1
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2022-02-10 2022-05-05
Small craft — Electrical/electronic control systems for
steering, shift and throttle
AMENDMENT 1
Petits navires — Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des
gaz
AMENDEMENT 1
ICS: 47.080
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 25197:2020/DAM 1:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
SIST EN ISO 25197:2020/oprA1:2022
ISO 25197:2020/DAM 1:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 25197:2020/oprA1:2022
ISO 25197:2020/DAM 1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.