Small craft - Electrically operated bilge pumps (ISO 8849:2020)

This document specifies requirements for electrically operated bilge pumps intended for use in
removing bilge water. It applies to:
— direct current (DC) bilge pumps which operate at a nominal voltage not exceeding 50 V; and
— single phase alternating current (AC) bilge pumps which operate at a nominal voltage not
exceeding 250 V.
It does not cover pumps intended for damage control.

Kleine Wasserfahrzeuge - Elektrisch angetriebene Bilgepumpen (ISO 8849:2020)

Dieses Dokument legt Anforderungen an elektrisch betriebene Bilgepumpen fest, die dazu vorgesehen sind, Bilgewasser zu entfernen. Es gilt für
- Gleichstrom-Bilgepumpen, die mit einer Nennspannung von weniger als 50 V arbeiten, und
- einphasige Wechselstrom-Bilgepumpen, die mit einer Nennspannung von weniger als 250 V arbeiten.
Es gilt nicht für Pumpen, die zur Schadensbegrenzung vorgesehen sind.

Petits navires - Pompes de cale à moteur électrique (ISO 8849:2020)

Le présent document spécifie les exigences relatives aux pompes de cale à moteur électrique prévues pour pomper l'eau de cale. Il s'applique aux:
—          pompes de cale à courant continu (d.c.) fonctionnant sous une tension nominale ne dépassant pas 50 V; et
—          pompes de cale à courant alternatif (a.c.) monophasé fonctionnant sous une tension nominale ne dépassant pas 250 V.
Il ne traite pas des pompes destinées au contrôle d'une avarie.

Mala plovila - Električne kalužne črpalke (ISO 8849:2020)

General Information

Status
Published
Public Enquiry End Date
31-May-2019
Publication Date
03-Jun-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
27-May-2021
Due Date
01-Aug-2021
Completion Date
04-Jun-2021

Relations

Buy Standard

Standard
EN ISO 8849:2021
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 8849:2019
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8849:2021
01-julij-2021
Nadomešča:
SIST EN ISO 8849:2018
Mala plovila - Električne kalužne črpalke (ISO 8849:2020)
Small craft - Electrically operated bilge pumps (ISO 8849:2020)
Kleine Wasserfahrzeuge - Elektrisch angetriebene Bilgepumpen (ISO 8849:2020)
Petits navires - Pompes de cale à moteur électrique (ISO 8849:2020)
Ta slovenski standard je istoveten z: EN ISO 8849:2021
ICS:
47.020.60 Električna oprema ladij in Electrical equipment of ships
konstrukcij na morju and of marine structures
47.080 Čolni Small craft
SIST EN ISO 8849:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 8849:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 8849:2021


EN ISO 8849
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2021
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 8849:2018
English Version

Small craft - Electrically operated bilge pumps (ISO
8849:2020)
Petits navires - Pompes de cale à moteur électrique Kleine Wasserfahrzeuge - Elektrisch angetriebene
(ISO 8849:2020) Bilgepumpen (ISO 8849:2020)
This European Standard was approved by CEN on 16 May 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8849:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 8849:2021
EN ISO 8849:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------
SIST EN ISO 8849:2021
EN ISO 8849:2021 (E)
European foreword
This document (EN ISO 8849:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2021, and conflicting national standards
shall be withdrawn at the latest by May 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8849:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8849:2020 has been approved by CEN as EN ISO 8849:2021 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 8849:2021
EN ISO 8849:2021 (E)
Annex ZA
(informative)

Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request
M/542 C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding Essential Requirements
of that Directive and associated EFTA regulations.
Table ZA.1 - Correspondence between this European Standard and Directive 2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of Remarks/Notes
Directive 2013/53/EU this EN
Annex I, Part A, 2.5 – Owner’s 4.10, 7
manual
Annex I, Part A, 3.5 – 4, 5, 6 In respect of electrically operated
Flooding, (c) removal of bilge pumps intended for the
water by pumps or other removing bilge water only.
means.
This International Standard does
not cover pumps intended for
damage control.
Annex I, Part A, 5.3 - 4.3, 4.8, 5 In respect of the electrical
Electrical system requirements to ensure the
proper operation of electrically
operated bilge pumps only.
This International Standard does
not deal with the following
elements of this essential
requirement;
• Electric shock;
• Interaction with electric
propulsion circuits;
• Battery ventilation
Annex I, Part A, 5.6.1 – Fire 4.2, 4.9, 4.10, 5.3 In respect of preventing a fire
protection, General hazard
Annex II, Components (1) 4, 5.1 to 5.4 inclusive, 6 This standard is relevant in
Ignition protected equipment respect of the requirements for
for inboard and stern drive ignition protected electrically
engines and petrol tank operated bilge pumps that are
spaces suitable for watercraft with
4

---------------------- Page: 6 ----------------------
SIST EN ISO 8849:2021
EN ISO 8849:2021 (E)
inboard or stern drive engines
and petrol tank spaces and which
are supplied as components.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

5

---------------------- Page: 7 ----------------------
SIST EN ISO 8849:2021

---------------------- Page: 8 ----------------------
SIST EN ISO 8849:2021
INTERNATIONAL ISO
STANDARD 8849
Third edition
2020-12
Small craft — Electrically operated
bilge pumps
Petits navires — Pompes de cale à moteur électrique
Reference number
ISO 8849:2020(E)
©
ISO 2020

---------------------- Page: 9 ----------------------
SIST EN ISO 8849:2021
ISO 8849:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 8849:2021
ISO 8849:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Electrical requirements . 3
6 Marking . 4
7 Owner’s manual. 4
Bibliography . 5
© ISO 2020 – All rights reserved iii

---------------------- Page: 11 ----------------------
SIST EN ISO 8849:2021
ISO 8849:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in
...

SLOVENSKI STANDARD
oSIST prEN ISO 8849:2019
01-maj-2019
0DODSORYLOD(OHNWULþQHNDOXåQHþUSDONH ,62',6
Small craft - Electrically operated bilge pumps (ISO/DIS 8849:2019)
Kleine Wasserfahrzeuge - Elektrisch angetriebene Bilgepumpen (ISO/DIS 8849:2019)
Petits navires - Pompes de cale à moteur électrique (ISO/DIS 8849:2019)
Ta slovenski standard je istoveten z: prEN ISO 8849
ICS:
47.020.60 (OHNWULþQDRSUHPDODGLMLQ Electrical equipment of ships
NRQVWUXNFLMQDPRUMX and of marine structures
47.080 ýROQL Small craft
oSIST prEN ISO 8849:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 8849:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 8849:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8849
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2019-03-22 2019-06-14
Small craft — Electrically operated bilge pumps
ICS: 47.080
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8849:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 8849:2019
ISO/DIS 8849:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 8849:2019
ISO/DIS 8849:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Electrical requirements . 3
6 Marking . 4
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 8849:2019
ISO/DIS 8849:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
The committee responsible for this document is Technical Committee ISO/TC 188, Small craft.
This third edition cancels and replaces the second edition (ISO 8849:2003), which has been technically
revised.
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 8849:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 8849:2019(E)
Small craft — Electrically operated bilge pumps
1 Scope
This document specifies requirements for electrically operated bilge pumps intended for use in
removing bilge water. It applies to electrically operated bilge pumps rated for less than 50 V direct
current d.c. or 300 V or less alternating current.
This International Standard does not cover pumps intended for damage control.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8846, Small craft — Electrical devices — Protection against ignition of surrounding flammable gases
ISO 10133, Small craft — Electrical systems — Extra-low-voltage d.c. installations
ISO 13297, Small Craft — Electrical Sys
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.