SIST EN 4612-002:2019

Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 002: General

This document specifies the characteristics of UV laser printable jacket, tin plated copper conductor, electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on board electrical systems of aircraft operating at temperatures between - 65 °C and 135 °C at 600 V rms at sea level. This insulation system has been used in aerospace applications using 115 V (phase-to-neutral) 400 Hz ac and 28 Vdc. Verification of the suitability of cables for use in other electrical systems is the responsibility of the user.
These jacketed cables are suitable for airframe use without additional protection when the jacket is present. When the jacket is stripped back the cores may need additional protection. In case of conflict between this document and other referenced documents the requirements of this document shall take precedence.

Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungenfür allgemeine Verwendung - XLETFE Familie - mit Mantel oder geschirmt und Mantel - Teil 002: Allgemeines

Dieses Dokument legt die Eigenschaften von elektrischen Leitungen mit UV-Laser bedruckbarem Mantel,
verzinntem Kupferleiter, aus der XLETFE-Familie (quervernetztes Ethylen-Tetrafluorethylen-Co-Polymer)
zur Verwendung in elektrischen Bordnetzen von Luftfahrzeugen für Betriebstemperaturen zwischen −65 °C
und 135 °C und bei 600 V (Effektivwert) auf Meereshöhe fest. Dieses Isoliersystem wurde bei Luft- und
Raumfahrtanwendungen mit 115 V (Phase gegen Neutral), 400 Hz Wechselspannung und 28 V Gleichspannung
angewendet. Der Anwender ist für den Nachweis der Eignung von Leitungen zur Anwendung in anderen
elektrischen Systemen verantwortlich.
Wenn der Mantel vorhanden ist, sind diese ummantelten Leitungen ohne zusätzlichen Schutz für die Verlegung
in Luftfahrzeugzellen geeignet. Bei abgezogenem Mantel benötigen die Adern unter Umständen einen
Zusatzschutz. Bei Widersprüchen zwischen dieser Norm und anderen zitierten Dokumenten gelten die Anforderungen
dieser Norm.

Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Gainés ou blindés et gainés - Partie 002 : Généralités

Aeronavtika - Kabli, električni, za splošne namene, eno- ali večžilni - Družina XLETFE - Oplaščeni ali zaslonjeni in oplaščeni - 002. del: Splošno

Ta dokument določa lastnosti električnih oplaščenih kablov, potiskljivih z UV-laserjem, z vodnikom iz pocinjenega bakra iz družine kopolimerov, pridobljenih z mrežno polimerizacijo etilena in tetrafluoroetilena (XLETFE), za uporabo v električnih sistemih na krovu letal pri obratovalnih temperaturah med –65 in 135 °C pri napetosti 600 V RMS na morski gladini. Ta izolacijski sistem se je uporabljal v aeronavtiki pri izmenični napetosti 115 V (za fazno napetost) pri 400 Hz in 28 V pri enosmerni napetosti. Za preverjanje ustreznosti kablov za uporabo v drugih električnih sistemih je odgovoren uporabnik.
Ti oplaščeni kabli so primerni za uporabo na ogrodjih letal brez dodatne zaščite, kadar je prisoten plašč. Kadar je plašč odstranjen, ožilje morda potrebuje dodatno zaščito. V primeru neskladja med tem dokumentom in drugimi navedenimi dokumenti imajo prednost določila tega dokumenta.

General Information

• Status: Published
• Publication Date: 10-Sep-2019
• ICS: 29.060.20 - Cables
• ICS: 49.060 - Aerospace electric equipment and systems
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 02-Sep-2019
• Due Date: 07-Nov-2019
• Completion Date: 11-Sep-2019
• Ref Project: EN 4612-002:2019 - Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 002: Genera

Relations

• Revised: SIST EN 4612-002:2011 - Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 002: General
• Effective Date: 29-Sep-2016
• Replaces: SIST EN 4612-002:2011 - Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 002: General
• Effective Date: 28-Aug-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 4612-002:2019
01-november-2019
Nadomešča:
SIST EN 4612-002:2011
Aeronavtika - Kabli, električni, za splošne namene, eno- ali večžilni - Družina
XLETFE - Oplaščeni ali zaslonjeni in oplaščeni - 002. del: Splošno
Aerospace series - Cables, electrical, for general purpose, single and multicore
assembly - XLETFE Family - Jacketed or screened and jacketed - Part 002: General
Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungenfür allgemeine
Verwendung - XLETFE Familie - mit Mantel oder geschirmt und Mantel - Teil 002:
Allgemeines
Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs -
Famille XLETFE - Gainés ou blindés et gainés - Partie 002 : Généralités
Ta slovenski standard je istoveten z: EN 4612-002:2019
ICS:
29.060.20 Kabli Cables
49.060 Letalska in vesoljska Aerospace electric
električna oprema in sistemi equipment and systems
SIST EN 4612-002:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 4612-002:2019

---------------------- Page: 2 ----------------------
SIST EN 4612-002:2019


EN 4612-002
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2019
EUROPÄISCHE NORM
ICS 49.060 Supersedes EN 4612-002:2011
English Version

Aerospace series - Cables, electrical, for general purpose,
single and multicore assembly - XLETFE Family - Jacketed
or screened and jacketed - Part 002: Genera
Série aérospatiale - Câbles, électriques, d'usage Luft- und Raumfahrt - Ein- und mehradrige elektrische
général, mono et multiconducteurs - Famille XLETFE - Leitungenfür allgemeine Verwendung - XLETFE
Gainés ou blindés et gainés - Partie 002 : Généralités Familie - mit Mantel oder geschirmt und Mantel - Teil
002: Allgemeines
This European Standard was approved by CEN on 5 May 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4612-002:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 4612-002:2019
EN 4612-002:2019 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 List of product standards . 5
5 Materials and construction . 6
6 Identification and marking . 8
7 Technical Specification . 9

2

---------------------- Page: 4 ----------------------
SIST EN 4612-002:2019
EN 4612-002:2019 (E)
European foreword
This document (EN 4612-002:2019) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2020, and conflicting national standards shall
be withdrawn at the latest by February 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 4612-002:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
3

---------------------- Page: 5 ----------------------
SIST EN 4612-002:2019
EN 4612-002:2019 (E)
1 Scope
This document specifies the characteristics of UV laser printable jacket, tin plated copper conductor,
electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the
on board electrical systems of aircraft operating at temperatures between – 65 °C and 135 °C at 600 V
rms at sea level. This insulation system has been used in aerospace applications using 115 V (phase-to-
neutral) 400 Hz ac and 28 Vdc. Verification of the suitability of cables for use in other electrical systems
is the responsibility of the user.
These jacketed cables are suitable for airframe use without additional protection when the jacket is
present. When the jacket is stripped back the cores may need additional protection. In case of conflict
between this standard and other referenced documents the requirements of this standard shall take
precedence.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2084, Aerospace series — Cables, electrical, general purpose, with conductors in copper or copper
alloy — Technical specification
EN 2235, Aerospace series — Single and multicore electrical cables, screened and jacketed — Technical
specification
EN 3475-100 (all parts), Aerospace series — Cables, electrical, aircraft use — Test methods — Part 100:
General
EN 3838, Aerospace series — Requirements and tests on user-applied markings on aircraft electrical cables
EN 4434, Aerospace series — Copper and copper alloy lightweight conductor
...