SIST EN ISO 4530:2023
(Main)Vitreous and porcelain enamelled manufactured articles - Determination of resistance to heat (ISO 4530:2022)
Vitreous and porcelain enamelled manufactured articles - Determination of resistance to heat (ISO 4530:2022)
This document specifies the basic conditions concerning the method for determining the resistance of
vitreous and porcelain enamelled articles to heat.
The method specified is applicable to vitreous and porcelain enamelled articles that will, in service, be
subjected to high temperature, for example to some cooker components, exhaust pipe silencers, gas
heating chimneys and flue pipes.
Emaillierte Gegenstände - Prüfung der Wärmebeständigkeit (ISO 4530:2022)
Dieses Dokument legt die Grundbedingungen für das Verfahren zur Bestimmung der Wärmebeständigkeit emaillierter Gegenstände fest.
Das festgelegte Verfahren ist auf emaillierte Gegenstände anwendbar, die im Gebrauch hohen Temperaturen ausgesetzt sind, z. B. für einige Herdteile, Abgas-Schalldämpfer, Gasheizungskamine und Abgasrohre.
Pièces manufacturées recouvertes d'émaux vitrifiés - Détermination de la résistance à la chaleur (ISO 4530:2022)
Le présent document spécifie les conditions de base de la méthode de détermination de la résistance à la chaleur des pièces manufacturées recouvertes d‘émaux vitrifiés.
La méthode spécifiée s’applique aux pièces manufacturées recouvertes d‘émaux vitrifiés soumises en service à des températures élevées, telles que, par exemple, certains éléments de cuisinières, les silencieux de tuyaux d’échappement, les cheminées de chauffage au gaz et les tuyaux de raccordement.
Stekleni in porcelanasto emajlirani industrijski izdelki - Določanje toplotne odpornosti (ISO 4530:2022)
Ta dokument določa osnovne pogoje v zvezi z metodo za določanje odpornosti
steklastih in porcelanasto emajliranih izdelkov proti toploti.
Navedena metoda se uporablja za steklaste in porcelanasto emajlirane izdelke, ki bodo med uporabo
izpostavljeni visoki temperaturi, na primer za nekatere komponente štedilnikov, dušilnike zvoka izpušnih cevi,
dimnike za plinsko ogrevanje in dimovodne cevi.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4530:2023
01-januar-2023
Stekleni in porcelanasto emajlirani industrijski izdelki - Določanje toplotne
odpornosti (ISO 4530:2022)
Vitreous and porcelain enamelled manufactured articles - Determination of resistance to
heat (ISO 4530:2022)
Emaillierte Gegenstände - Prüfung der Wärmebeständigkeit (ISO 4530:2022)
Pièces manufacturées recouvertes d'émaux vitrifiés - Détermination de la résistance à la
chaleur (ISO 4530:2022)
Ta slovenski standard je istoveten z: EN ISO 4530:2022
ICS:
25.220.50 Emajlne prevleke Enamels
SIST EN ISO 4530:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4530:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 4530:2023
EN ISO 4530
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2022
EUROPÄISCHE NORM
ICS 25.220.50
English Version
Vitreous and porcelain enamelled manufactured articles -
Determination of resistance to heat (ISO 4530:2022)
Pièces manufacturées recouvertes d'émaux vitrifiés - Emaillierte Gegenstände - Prüfung der
Détermination de la résistance à la chaleur (ISO Wärmebeständigkeit (ISO 4530:2022)
4530:2022)
This European Standard was approved by CEN on 29 October 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4530:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 4530:2023
EN ISO 4530:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 4530:2023
EN ISO 4530:2022 (E)
European foreword
This document (EN ISO 4530:2022) has been prepared by Technical Committee ISO/TC 107 "Metallic
and other inorganic coatings" in collaboration with Technical Committee CEN/TC 262 “Metallic and
other inorganic coatings, including for corrosion protection and corrosion testing of metals and alloys”
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2023, and conflicting national standards shall be
withdrawn at the latest by May 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 4530:2022 has been approved by CEN as EN ISO 4530:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 4530:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 4530:2023
INTERNATIONAL ISO
STANDARD 4530
Second edition
2022-10
Vitreous and porcelain enamelled
manufactured articles —
Determination of resistance to heat
Pièces manufacturées recouvertes d'émaux vitrifiés — Détermination
de la résistance à la chaleur
Reference number
ISO 4530:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 4530:2023
ISO 4530:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 4530:2023
ISO 4530:2022(E)
Contents Page
Foreword .iv
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 G ener a l . 1
5 P r i nc iple . 2
6 A pp a r at u s . 2
7 S a mpl i n g . 2
8 P r o c e du re .2
9 Te s t r ep or t .
...
SLOVENSKI STANDARD
oSIST prEN ISO 4530:2022
01-marec-2022
Stekleni in porcelanasto emajlirani industrijski izdelki - Določanje toplotne
odpornosti (ISO/DIS 4530:2021)
Vitreous and porcelain enamelled manufactured articles - Determination of resistance to
heat (ISO/DIS 4530:2021)
Emaillierte Gegenstände – Prüfung der Wärmebeständigkeit (ISO/DIS 4530:2021)
Pièces manufacturées recouvertes d'émaux vitrifiés - Détermination de la résistance à la
chaleur (ISO/DIS 4530:2021)
Ta slovenski standard je istoveten z: prEN ISO 4530
ICS:
25.220.50 Emajlne prevleke Enamels
oSIST prEN ISO 4530:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 4530:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 4530:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4530
ISO/TC 107 Secretariat: KATS
Voting begins on: Voting terminates on:
2021-12-28 2022-03-22
Vitreous and porcelain enamelled manufactured articles —
Determination of resistance to heat
Pièces manufacturées recouvertes d'émaux vitrifiés — Détermination de la résistance à la chaleur
ICS: 25.220.50
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 4530:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 4530:2022
ISO/DIS 4530:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 4530:2022
ISO/DIS 4530:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 1
6 Sampling . 1
7 Procedure .2
8 Test report . 2
iii
© ISO 2021 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 4530:2022
ISO/DIS 4530:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any p
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.