SIST EN ISO 15749-4:2004

Ships and marine technology - Drainage systems on ships and marine structures - Part 4: Sanitary drainage, sewage disposal pipes (ISO 15749-4:2004)

ISO 15749-4:2004 applies to the design of sewage disposal pipes within the framework of sanitary drainage on ships and marine structures.
For planning and basic requirements, see ISO 15749-1:2004.

Schiffe und Meerestechnik - Entwässerungsanlagen auf Schiffen und Seebauwerken - Teil 4: Sanitär-Entwässerung, Schwarzwasser-Entleerungsleitungen (ISO 15749-4:2004)

Diese Norm gilt für die Konstruktion von Entleerungsleitungen der Sanitär-Entwässerung auf Schiffen und Seebau-werken.
Für die Planung und grundsätzlichen Anforderungen gilt ISO 15749-1.

Navires et technologie maritime - Installations de drainage sur navires et structures maritimes - Partie 4: Drainage sanitaire, tuyaux d'évacuation des eaux usées (ISO 15749-4:2004)

Ladje in pomorska tehnologija – Sistemi za odvajanje vode/odplak z ladij in struktur na morju – 4. del: Sanitarni sistem, praznjenje (ISO 15749-4:2004)

General Information

• Status: Published
• Publication Date: 31-Aug-2004
• ICS: 47.020.30 - Piping systems
• Technical Committee: SS SPL - Technical Board for the general field
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Sep-2004
• Due Date: 01-Sep-2004
• Completion Date: 01-Sep-2004
• Ref Project: EN ISO 15749-4:2004 - Ships and marine technology - Drainage systems on ships and marine structures - Part 4: Sanitary drainage, sewage disposal pipes (ISO 15749-4:2004)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15749-4:2004
01-september-2004
Ladje in pomorska tehnologija – Sistemi za odvajanje vode/odplak z ladij in
struktur na morju – 4. del: Sanitarni sistem, praznjenje (ISO 15749-4:2004)
Ships and marine technology - Drainage systems on ships and marine structures - Part
4: Sanitary drainage, sewage disposal pipes (ISO 15749-4:2004)
Schiffe und Meerestechnik - Entwässerungsanlagen auf Schiffen und Seebauwerken -
Teil 4: Sanitär-Entwässerung, Schwarzwasser-Entleerungsleitungen (ISO 15749-4:2004)
Navires et technologie maritime - Installations de drainage sur navires et structures
maritimes - Partie 4: Drainage sanitaire, tuyaux d'évacuation des eaux usées (ISO 15749
-4:2004)
Ta slovenski standard je istoveten z: EN ISO 15749-4:2004
ICS:
47.020.30 Sistemi cevi Piping systems
SIST EN ISO 15749-4:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15749-4:2004

---------------------- Page: 2 ----------------------

SIST EN ISO 15749-4:2004
EUROPEAN STANDARD
EN ISO 15749-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2004
ICS 47.020.30
English version
Ships and marine technology - Drainage systems on ships and
marine structures - Part 4: Sanitary drainage, sewage disposal
pipes (ISO 15749-4:2004)
Navires et technologie maritime - Installations de drainage
sur navires et structures maritimes - Partie 4: Drainage
sanitaire, tuyaux d'évacuation des eaux usées (ISO 15749-
4:2004)
This European Standard was approved by CEN on 7 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15749-4:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15749-4:2004
EN ISO 15749-4:2004 (E)


Foreword

This document (EN ISO 15749-4:2004) has been prepared by Technical Committee ISO/TC 8
"Ships and marine technology" in collaboration with Technical Committee CEN/TC 300 "Sea-
going vessels and marine technology", the secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2004, and conflicting national
standards shall be withdrawn at the latest by December 2004.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice

The text of ISO 15749-4:2004 has been approved by CEN as EN ISO 15749-4:2004 without any
modifications.
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15749-4:2004


INTERNATIONAL ISO
STANDARD 15749-4
First edition
2004-06-15


Ships and marine technology — Drainage
systems on ships and marine
structures —
Part 4:
Sanitary drainage, sewage disposal pipes
Navires et technologie maritime — Installations de drainage sur navires
et structures maritimes —
Partie 4: Drainage sanitaire, tuyaux d'évacuation des eaux usées




Reference number
ISO 15749-4:2004(E)
©
ISO 2004

---------------------- Page: 5 ----------------------

SIST EN ISO 15749-4:2004
ISO 15749-4:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2004 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 15749-4:2004
ISO 15749-4:2004(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 1
4 Disposal . 2
5 Wastewater outlets . 13
6 Pipework . 14
Bibliography . 15

© ISO 2004 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 15749-4:2004
ISO 15749-4:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15749-4 was prepared by Technical Committee ISO/TC 8, Ships and marine techology, Subcommittee
SC 3, Piping and machinery.
ISO 15749 consists of the following parts, under the general title Ships and marine technology — Drainage
systems on ships and marine structures:
 Part 1: Sanitary drainage-system design
 Part 2: Sanitary drainage, drain piping for gravity systems
 Part 3: Sanitary drainage, drain piping for vacuum systems
 Part 4: Sanitary drainage, sewage disposal pipes
 Part 5: Drainage of decks, cargo spaces and swimming pools

iv © ISO 2004 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15749-4:2004
INTERNATIONAL STANDARD ISO 15749-4:2004(E)

Ships and marine technology — Drainage systems on ships
and marine structures —
Part 4:
Sanitary drainage, sewage disposal pipes
1 Scope
This part of ISO 15749 applies to the design of sewage disposal pipes within the framework of sanitary
drainage on ships and marine structures.
For planning and basic requirements, see ISO 15749-1.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4200, Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit
length
ISO 9329-1, Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 1: Unalloyed
steels with specified room temperature properties
ISO 9330-1, Welded steel tubes for pressure purposes — Technical delivery conditions — Part 1: Unalloyed
steel tubes with specified room temperature properties
ISO 15749-1, Ships and marine technology — Drainage systems on ships and marine structures —
Part 1: Sanitary drainage-system design
ISO 15749-5, Ships and marine technology — Drainage systems on ships and marine structures —
Part 5: Drainage of decks, cargo spaces and swimming pools
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 15749-1 apply.
© ISO 2004 – All rights reserved 1

---------------------- Page: 9 ----------------------

SIST EN ISO 15749-4:2004
ISO 15749-4:2004(E)
4 Disposal
4.1 General
For the disposal of wastewater from sanitary drainage systems, a distinction is made between:
 overboard wastewater disposal via a wastewater storage unit and disposal pipes overboard or to a
connection from where it is transferred to an external disposal point (see 4.2);
NOTE Wastewater storage units according to this part of ISO 15749 are collector tanks, sewage treatment plants, or
vacuum generating units for the respective facilities
 discharge directly overboard via gravity drain lines (see 4.4).
4.2 Disposal points with storage units
4.2.1 Disposal piping system
Disposal lines from storage units to disposal points shall be designed as pressure lines; for details see
Figure 1.
Figure 1 shows a simplified example of routing of disposal lines within the framework of a sanitary drainage
system, leading from the storage unit (e.g. collector tank, sewage treatment plant) to the disposal points.
4.2.2 Discharge over the side
4.2.2.1 Closing devices
As closing devices, fittings shall be installed in the disposal piping section between the wastewater pump and
the wastewater outlet (piping section Z); see Figure 2. Closing devices shall be certified by the classification
societies.
The arrangement, number, and type of fittings depends on the vertical distance from the summer
loadline/bulkhead deck of the lowest opening (drain).
NOTE Such openings (drains) also include, for example, emergency overflows of sewage treatment plants or
openings for dosing of chemicals.
4.2.2.2 Drains
4.2.2.2.1 In the disposal pipe, a screw-down non-return valve shall be installed at the shell. If it is not
possible to place the shutoff fitting directly at the shell, the pipe from the shell to the shutoff fitting has to be
designed thick-walled, see 6.1 and Figure 3.
2 © ISO 2004 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15749-4:2004
ISO 15749-4:2004(E)

Key
1 sewage treatment plant, collector tank or vacuum  9 funnel
generating unit for these installations
10 cargo space
2 disposal pipe
11 bridge
th
3 valve
12 4 superstructure deck
rd
4 wastewater pump
13 3 superstructure deck
nd
5 non-return valve
14 2 superstructure deck
st
6 vent line
15 1 superstructure deck
7 wastewater outlet in the shell
16 freeboard/bulkhead deck
8 international wastewater shore connection
(MARPOL-flange)
a
Wastewater from accommodation areas and service
spaces.
Figure 1 — Example of a sewage disposal system with storage unit upstream of the discharge poi
...