Non-destructive testing of steel tubes - Part 3: Automated full peripheral flux leakage testing of seamless and welded (except submerged arc-welded) ferromagnetic steel tubes for the detection of longitudinal and/or transverse imperfections - Amendment 1 (ISO 10893-3:2011/Amd 1:2019)

This part of ISO 10893 specifies requirements for automated full peripheral magnetic flux leakage testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc-welded (SAW) tubes, for the detection of imperfections. Unless otherwise specified in the purchase order, this part of ISO 10893 is applicable to the detection of predominantly longitudinal imperfections. This part of ISO 10893 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm. This part of ISO 10893 can also be applicable to the testing of hollow sections.

Zerstörungsfreie Prüfung von Stahlrohren - Teil 3: Automatisierte Streuflussprüfung nahtloser und geschweißter (ausgenommen unterpulvergeschweißter) ferromagnetischer Stahlrohre über den gesamten Rohrumfang zum Nachweis von Unvollkommenheiten in Längs- und/oder Querrichtung - Änderung 1 (ISO 10893-3:2011/Amd 1:2019)

Essais non destructifs des tubes en acier - Partie 3: Contrôle automatisé par flux de fuite sur toute la circonférence des tubes en acier ferromagnétique sans soudure et soudés (sauf à l'arc immergé sous flux en poudre) pour la détection des imperfections longitudinales et/ou transversales - Amendement 1 (ISO 10893-3:2011/Amd 1:2019)

Neporušitveno preskušanje jeklenih cevi - 3. del: Ugotavljanje prečnih/vzdolžnih napak po celotnem obodu feromagnetnih jeklenih cevi, nevarjenih in varjenih (razen obločno varjenih pod praškom), z avtomatsko preiskavo z magnetno sondo - Dopolnilo A1 (ISO 10893-3:2011/Amd 1:2019)

Ta del ISO 10893 določa zahteve za ugotavljanje prečnih/vzdolžnih napak po celotnem obodu feromagnetnih jeklenih cevi, nevarjenih in varjenih, razen cevi, obločno varjenih pod praškom (SAW), z avtomatsko preiskavo z magnetno sondo. Razen če je v dobavnici določeno drugače, ta del ISO 10893 velja predvsem za odkrivanje vzdolžnih napak. Velja za pregled cevi z zunanjim premerom, večjim ali enakim 10 mm. Ta del ISO 10893 lahko velja tudi za preskušanje votlih delov.

General Information

Status
Published
Public Enquiry End Date
26-Jun-2019
Publication Date
04-Nov-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
24-Oct-2019
Due Date
29-Dec-2019
Completion Date
05-Nov-2019

Relations

Buy Standard

Amendment
EN ISO 10893-3:2011/A1:2020
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
EN ISO 10893-3:2011/oprA1:2019
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10893-3:2011/A1:2020
01-januar-2020
Neporušitveno preskušanje jeklenih cevi - 3. del: Ugotavljanje prečnih/vzdolžnih
napak po celotnem obodu feromagnetnih jeklenih cevi, nevarjenih in varjenih
(razen obločno varjenih pod praškom), z avtomatsko preiskavo z magnetno sondo
- Dopolnilo A1 (ISO 10893-3:2011/Amd 1:2019)
Non-destructive testing of steel tubes - Part 3: Automated full peripheral flux leakage
testing of seamless and welded (except submerged arc-welded) ferromagnetic steel
tubes for the detection of longitudinal and/or transverse imperfections - Amendment 1
(ISO 10893-3:2011/Amd 1:2019)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 3: Automatisierte Streuflussprüfung
nahtloser und geschweißter (ausgenommen unterpulvergeschweißter)
ferromagnetischer Stahlrohre über den gesamten Rohrumfang zum Nachweis von
Unvollkommenheiten in Längs- und/oder Querrichtung - Änderung 1 (ISO 10893-
3:2011/Amd 1:2019)
Essais non destructifs des tubes en acier - Partie 3: Contrôle automatisé par flux de fuite
sur toute la circonférence des tubes en acier ferromagnétique sans soudure et soudés
(sauf à l'arc immergé sous flux en poudre) pour la détection des imperfections
longitudinales et/ou transversales - Amendement 1 (ISO 10893-3:2011/Amd 1:2019)
Ta slovenski standard je istoveten z: EN ISO 10893-3:2011/A1:2019
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-3:2011/A1:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 10893-3:2011/A1:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 10893-3:2011/A1:2020


EN ISO 10893-3:2011/A1
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2019
EUROPÄISCHE NORM
ICS 77.140.75; 23.040.10; 77.040.20
English Version

Non-destructive testing of steel tubes - Part 3: Automated
full peripheral flux leakage testing of seamless and welded
(except submerged arc-welded) ferromagnetic steel tubes
for the detection of longitudinal and/or transverse
imperfections - Amendment 1: Change of dimensions of
the reference notch (ISO 10893-3:2011/Amd 1:2019)
Essais non destructifs des tubes en acier - Partie 3: Zerstörungsfreie Prüfung von Stahlrohren - Teil 3:
Contrôle automatisé par flux de fuite sur toute la Automatisierte Streuflussprüfung nahtloser und
circonférence des tubes en acier ferromagnétique sans geschweißter (ausgenommen
soudure et soudés (sauf à l'arc immergé sous flux en unterpulvergeschweißter) ferromagnetischer
poudre) pour la détection des imperfections Stahlrohre über den gesamten Rohrumfang zum
longitudinales et/ou transversales - Amendement 1: Nachweis von Unvollkommenheiten in Längs-
Changements de dimensions de l'encoche de référence und/oder Querrichtung - Änderung 1 (ISO 10893-
(ISO 10893-3:2011/Amd 1:2019) 3:2011/Amd 1:2019)
This amendment A1 modifies the European Standard EN ISO 10893-3:2011; it was approved by CEN on 28 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10893-3:2011/A1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 10893-3:2011/A1:2020
EN ISO 10893-3:2011/A1:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 10893-3:2011/A1:2020
EN ISO 10893-3:2011/A1:2019 (E)
European foreword
This document (EN ISO 10893-3:2011/A1:2019) has been prepared by Technical Committee ISO/TC 17
"Steel" in collaboration with Technical Committee CEN/TC 459/SC 10 “Steel tubes, and iron and steel
fittings” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent
...

SLOVENSKI STANDARD
SIST EN ISO 10893-3:2011/oprA1:2019
01-junij-2019
1HSRUXãLWYHQRSUHVNXãDQMHMHNOHQLKFHYLGHO8JRWDYOMDQMHSUHþQLKY]GROåQLK
QDSDNSRFHORWQHPRERGXIHURPDJQHWQLKMHNOHQLKFHYLQHYDUMHQLKLQYDUMHQLK
UD]HQREORþQRYDUMHQLKSRGSUDãNRP ]DYWRPDWVNRSUHLVNDYR]PDJQHWQRVRQGR
'RSROQLOR$ ,62'$0
Non-destructive testing of steel tubes - Part 3: Automated full peripheral flux leakage
testing of seamless and welded (except submerged arc-welded) ferromagnetic steel
tubes for the detection of longitudinal and/or transverse imperfections - Amendment 1
(ISO 10893-3:2011/DAM 1:2019)
Zerstörungsfreie Prüfung von Stahlrohren - Teil 3: Automatisierte Streuflussprüfung
nahtloser und geschweißter (ausgenommen unterpulvergeschweißter) ferromagnetischer
Stahlrohre über den gesamten Rohrumfang zum Nachweis von Unvollkommenheiten in
Längs- und/oder Querrichtung - Änderung 1 (ISO 10893-3:2011/DAM 1:2019)
Essais non destructifs des tubes en acier - Partie 3: Contrôle automatisé par flux de fuite
sur toute la circonférence des tubes en acier ferromagnétique sans soudure et soudés
(sauf à l'arc immergé sous flux en poudre) pour la détection des imperfections
longitudinales et/ou transversales - Amendement 1 (ISO 10893-3:2011/DAM 1:2019)
1:2019)
Ta slovenski standard je istoveten z: EN ISO 10893-3:2011/prA1
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.040.20 Neporušitveno preskušanje Non-destructive testing of
kovin metals
SIST EN ISO 10893-3:2011/oprA1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10893-3:2011/oprA1:2019

---------------------- Page: 2 ----------------------

SIST EN ISO 10893-3:2011/oprA1:2019
DRAFT AMENDMENT
ISO 10893-3:2011/DAM 1
ISO/TC 17/SC 19 Secretariat: UNI
Voting begins on: Voting terminates on:
2019-04-04 2019-06-27
Non-destructive testing of steel tubes —
Part 3:
Automated full peripheral flux leakage testing of seamless
and welded (except submerged arc-welded) ferromagnetic
steel tubes for the detection of longitudinal and/or
transverse imperfections
AMENDMENT 1
Essais non destructifs des tubes en acier —
Partie 3: Contrôle automatisé par flux de fuite sur toute la circonférence des tubes en acier
ferromagnétique sans soudure et soudés (sauf à l'arc immergé sous flux en poudre) pour la détection des
imperfections longitudinales et/ou transversales
AMENDEMENT 1
ICS: 77.140.75; 77.040.20; 23.040.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 10893-3:2011/DAM 1:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.