iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 62271-101:2006/A1:2010

(Amendment)

High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-101:2006/A1:2010)

High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-101:2006/A1:2010)

Amandma A1:2010 je dodatek k standardu SIST EN 62271-101:2006
This part of IEC 62271 mainly applies to a.c. circuit-breakers within the scope of IEC 62271- 100. It provides the general rules for testing a.c. circuit-breakers, for making and breaking capacities over the range of test duties described in 6.102 to 6.111 of IEC 62271-100, by synthetic methods. It has been proven that synthetic testing is an economical and technically correct way to test high-voltage a.c. circuit-breakers according to the requirements of IEC 62271-100 and that it is equivalent to direct testing. The methods and techniques described are those in general use. The purpose of this standard is to establish criteria for synthetic testing and for the proper evaluation of results. Such criteria will establish the validity of the test method without imposing restraints on innovation of test circuitry.

Hochspannungs-Schaltgeräte und -Schaltanlagen - Teil 101: Synthetische Prüfung (IEC 62271-101:2006/A1:2010)

Appareillage à haute tension - Partie 101: Essais synthétiques (CEI 62271-101:2006/A1:2010)

Visokonapetostne stikalne in krmilne naprave - 101. del: Sintetično preskušanje (IEC 62271-101:2006/A1:2010)

Amandma A1:2010 je dodatek k standardu SIST EN 62271-101:2006
Ta del IEC 6227 večinoma velja za prekinjevalce izmeničnega toku v okviru IEC 62271-100. Zagotavlja splošna pravila za preskušanje prekinjevalcev izmeničnega toka, za zmogljivost proizvajanja in prekinitve v razponu preskusnih funkcij, ki so opisane od točke 6.102 do 6.111 IEC 62271-100, s sintetičnimi metodami. Dokazano je bilo, da je sintetično preskušanje ekonomičen in tehnično pravilen način preskušanja visoko napetostnih prekinjevalcev izmeničnega toka v skladu z zahtevami IEC 62271-100 ter da je enakovredno neposrednemu preskušanju. Opisane metode in tehnike so tiste, ki so v splošni rabi. Namen tega standarda je vzpostaviti merila za sintetično preskušanje in za primerno ovrednotenje rezultatov. Takšna merila vzpostavljajo veljavnost preskusne metode brez omejitev glede inovativnosti preskusnega vezja.

General Information

Status
Withdrawn
Publication Date
07-Oct-2010
Withdrawal Date
01-Jun-2016
ICS
29.130.10 - High voltage switchgear and controlgear
Technical Committee
SKA - Switchgear and control gear
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
02-Jun-2016
Due Date
25-Jun-2016
Completion Date
02-Jun-2016
Ref Project
EN 62271-101:2006/A1:2010 - High-voltage switchgear and controlgear - Part 101: Synthetic testing

Relations

Replaced By
SIST EN 62271-101:2013 - High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-101:2012)
Effective Date
28-Jan-2023
Replaced By
SIST EN 62271-101:2013 - High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-101:2012)
Effective Date
07-Jun-2022
Amends
SIST EN 62271-101:2006 - High-voltage switchgear and controlgear -- Part 101: Synthetic testing
Effective Date
01-Nov-2010
Replaced By
SIST EN 62271-101:2013 - High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-101:2012)
Effective Date
01-Mar-2013
Amends
SIST EN 62271-101:2006 - High-voltage switchgear and controlgear -- Part 101: Synthetic testing
Effective Date
29-Jan-2023
Amends
SIST EN 62271-101:2006 - High-voltage switchgear and controlgear -- Part 101: Synthetic testing
Effective Date
07-Jun-2022

Buy Standard

EN 62271-101:2006/A1:2010EN 62271-101:2006/A1:2010
PreviousNext
Amendment
EN 62271-101:2006/A1:2010
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62271-101:2006/A1:2010
01-november-2010
9LVRNRQDSHWRVWQHVWLNDOQHLQNUPLOQHQDSUDYHGHO6LQWHWLþQRSUHVNXãDQMH
,(&$
High-voltage switchgear and controlgear - Part 101: Synthetic testing (IEC 62271-
101:2006/A1:2010)
Hochspannungs-Schaltgeräte und -Schaltanlagen - Teil 101: Synthetische Prüfung (IEC
62271-101:2006/A1:2010)
Appareillage à haute tension - Partie 101: Essais synthétiques (CEI 62271-
101:2006/A1:2010)
Ta slovenski standard je istoveten z: EN 62271-101:2006/A1:2010
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 62271-101:2006/A1:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62271-101:2006/A1:2010

---------------------- Page: 2 ----------------------

SIST EN 62271-101:2006/A1:2010

EUROPEAN STANDARD
EN 62271-101/A1

NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM

ICS 29.130.10


English version


High-voltage switchgear and controlgear -
Part 101: Synthetic testing
(IEC 62271-101:2006/A1:2010)


Appareillage à haute tension -  Hochspannungs-Schaltgeräte
Partie 101: Essais synthétiques und -Schaltanlagen -
(CEI 62271-101:2006/A1:2010) Teil 101: Synthetische Prüfung
(IEC 62271-101:2006/A1:2010)




This amendment A1 modifies the European Standard EN 62271-101:2006; it was approved by CENELEC on
2010-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62271-101:2006/A1:2010 E

---------------------- Page: 3 ----------------------

SIST EN 62271-101:2006/A1:2010
EN 62271-101:2006/A1:2010 - 2 -
Foreword
The text of document 17A/907/FDIS, future amendment 1 to IEC 62271-1010:2006, prepared by SC 17A,
High-voltage switchgear and controlgear, of IEC TC 17, Switchgear and controlgear, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 662271-101:2006
on 2010-09-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
an identical national standard or by endorsement (dop) 2011-06-01
– latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of amendment 1:2010 to the International Standard IEC 62271-101:2006 was approved by
CENELEC as an amendment to the European Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 62271-101:2006/A1:2010
- 3 - EN 62271-101:2006/A1:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
IEC 62271-100 2001 High-voltage switchgear and controlgear - EN 62271-100 2001
Part 100: High-voltage alternating-current
circuit-breakers


IEC 62271-100 2008 High-voltage switchgear and controlgear - EN 62271-100 2009
Part 100: Alternating current circuit-breakers


IEC/TR 62271-308 2002 High-voltage switchgear and controlgear - - -
Part 308: Guide for asymmetrical short-circuit
breaking test duty T100a




1)
EN 62271-100 is superseded by EN 62271-100:2009, which is based on IEC 62271-100:2008.

---------------------- Page: 5 ----------------------

SIST EN 62271-101:2006/A1:2010

---------------------- Page: 6 ----------------------

SIST EN 62271-101:2006/A1:2010
IEC 62271-101
®
Edition 1.0 2010-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 1
AMENDEMENT 1
High-voltage switchgear and controlgear –
Part 101: Synthetic testing

Appareillage à haute tension –
Partie 101: Essais synthétiques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
P
CODE PRIX
ICS 29.130.10 ISBN 978-2-88910-928-9
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62271-101:2006/A1:2010
– 2 – 62271-101 Amend. 1 © IEC:2010
FOREWORD
This amendment has been prepared by subcommittee 17A: High-voltage switchgear and
controlgear, of IEC technical committee 17: Switchgear and controlgear.
The text of this amendment is based on the following documents:
FDIS Report on voting
17A/907/FDIS 17A/919/RVD

Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

_____________

INTRODUCTION
This amendment cancels and replaces IEC 61633.
The original edition of IEC 62271-101 (2006) makes extensive reference to
IEC 62271-100:2001. Since then, a new edition of IEC 62271-100 has been published (2008).
Within this amendment, references are made to IEC 62271-100:2008. Unless they are
explicitly mentioned in this amendment, all of the references in the original edition of
IEC 62271-101 (2006) still make reference to IEC 62271-100:2001. A second amendment to
IEC 62271-101, which will update all cross-references to the new IEC 62271-100:2008, is
under consideration.

Change "Tables I.1a through I.2d" to "Tables 15 through 22 of IEC 62271-100:2008" in the
whole document.

---------------------- Page: 8 ----------------------

SIST EN 62271-101:2006/A1:2010
62271-101 Amend. 1 © IEC:2010 – 3 –
2 Normative references
Delete reference to IEC 61633.
Add the following new reference (and footnote) to the existing list:
IEC 62271-100:2008, High-voltage switchgear and controlgear – Part 100: Alternating-current
1
circuit-breakers

4.2.4 Other synthetic test methods
In the second paragraph, replace “IEC 61633” by “Annex O of IEC 62271-100:2008”.

6 Specific requirements for synthetic tests for making and breaking
performance related to the requirements of 6.102 through 6.111 of
IEC 62271-100
Add the following text at the end on the first paragraph:
Annex O of IEC 62271-100:2008 gives guidelines for the testing of metal-enclosed and dead
tank circuit breakers.

Add the following subclause:
6.102.4.2 Unit testing
For the application of the synthetic test methods to one or more units of a circuit breaker, the
requirements of 6.102.4.2 of IEC 62271-100:2008 are applicable. In the case of metal-
enclosed or dead tank circuit-breakers, Annex N gives details of some typical test circuits and
Annex O of IEC 62271-100:2008 outlines appropriate testing guidelines.

6.111 Capacitive current switching tests
Add the following text:
For metal-enclosed and dead tank circuit-breakers, typical test circuits are given in Annex N
and additional guidelines are given in Annex O of IEC 62271-100:2008.

___________
1
 Unless explicitly otherwise mentioned, all of the references to IEC 62271-100 make reference to IEC 62271-100:2001. A
second amendment to IEC 62271-101, which will update all cross-references to the new IEC 62271-100:2008, is under
consideration.

---------------------- Page: 9 ----------------------

SIST EN 62271-101:2006/A1:2010
– 4 – 62271-101 Amend. 1 © IEC:2010

Figure 5
Replace the existing Figure 5 by the following new Figure 5:
IEC  961/10 IEC  962/10


Figure 5a – Synthetic make circuit for terminal fault
IEC  963/10

Figure 5b – Synthetic make circuit for out-of-phase (ac + dc method)

---------------------- Page: 10 ----------------------

SIST EN 62271-101:2006/A1:2010
62271-101 Amend. 1 © IEC:2010 – 5 –

L TR S L
1 t h
u i
t t
R
h
CH L U
u S pf h
cs a
C
h
L1
IEC  964/10

Figure 5c – Synthetic make circuit for out-of-phase (ac + ac method)
Key
S auxiliary circuit-breaker i current through S

a t t
S circuit-breaker under test L inductance of the current circuit

t 1
u voltage of the current circuit L
inductance of the voltage circuit
cs h
i current of the current circuit R C components of the ITMC circuit
cs h h
i injected current L parallel inductance of the voltage circuit

h pf
U applied voltage t time delay of making device
h m
CH making device (triggered spark gap)
Figure 5 – Typical synthetic make circuits for single-phase tests

G.1 Introduction
Add the following new text below the note:
For applicability of the mentioned methods in case of metal-enclosed or dead tank circuit-
breakers, see Annex N and Annex O of IEC 62271-100:2008.

G.1.2 Recovery
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 62271-110:2023(Main)
High-voltage switchgear and controlgear - Part 110: Inductive load switching (IEC 62271-110:2023)
EN IEC 62271-110:2023

This part of IEC 62271 is applicable to AC switching devices designed for indoor or outdoor
installation, for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above
1 000 V and applied for inductive current switching. It is applicable to switching devices
(including circuit-breakers in accordance with IEC 62271-100) that are used to switch
high-voltage motor currents and shunt reactor currents and also to high-voltage contactors used
to switch high-voltage motor currents as covered by IEC 62271-106.
Switching unloaded transformers, i.e. breaking transformer magnetizing current, is not
considered in this document. The reasons for this are as follows:
a) Owing to the non-linearity of the transformer core, it is not possible to correctly model the
switching of transformer magnetizing current using linear components in a test laboratory.
Tests conducted using an available transformer, such as a test transformer, will only be
valid for the transformer tested and cannot be representative for other transformers.
b) As detailed in IEC TR 62271-306, the characteristics of this duty are usually less severe
than any other inductive current switching duty. Such a duty can produce severe
overvoltages within the transformer winding(s) depending on the re-ignition behaviour of the
switching device and transformer winding resonance frequencies.
NOTE 1 The switching of tertiary reactors from the high-voltage side of the transformer is not covered by this
document.
NOTE 2 The switching of shunt reactors earthed through neutral reactors is not covered by this document. However,
the application of test results according to this document, on the switching of neutral reactor earthed reactors (4-leg
reactor scheme), is discussed in IEC TR 62271-306.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50089:2023(Main)
High-Voltage switchgear and controlgear - Insulating pressurised partitions for gas filled metal enclosures
EN 50089:2022

This document applies to pressurized partitions used in indoor and outdoor installations of high-voltage AC and DC switchgear and controlgear with rated voltages (Ur) above 1 kV AC / 1,5 kV DC and with design pressure higher than 300 kPa, where the gas is used principally for its dielectric and/or arc-quenching properties.
Gases with insulating properties are dry air, inert gases, for example sulphur hexafluoride or nitrogen or a mixture of such gases.
The partitions comprise pressurized barriers in electrical equipment not necessarily limited to the following examples:
—   circuit-breakers;
—   switch-disconnectors;
—   disconnectors;
—   earthing switches;
—   current transformers;
—   voltage transformers;
—   surge arrestors;
—   busbars and connections;
—   cable connections / terminations
—   cable bushings
—   etc.
Partitions which are only pressurized from one side are also covered.
1 kV AC / 1,5 kV DC means it is valid for the apparatus applied and where the partitions are installed, however, the application of voltages below 1 kV AC / 1,5 kV DC as in e.g. current and voltage transformer are not excluded.
This document does not apply to high voltage bushings (see EN 60137, EN 61462 and EN 62155).

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-4:2022(Main)
High-voltage switchgear and controlgear - Part 4: Handling procedures for gases for insulation and/or switching (IEC 62271-4:2022)
EN IEC 62271-4:2022

This part of IEC 62271 applies to the procedures for handling of gases and gas mixtures for insulation and/or switching during installation, commissioning, repair, overhaul, normal and abnormal operations and disposal at the end-of-life of high-voltage switchgear and controlgear.
These procedures are regarded as minimum requirements to ensure the reliability of electric power equipment, the safety of personal working with these gases and gas mixtures and to minimize the impact on the environment. Additional requirements could be given or specified in the operating instruction manual of the manufacturer.
For each gas or gas mixture, which is known to be used in electric power equipment at the date of the publication of this document, a separate annex describes specifications, handling procedures, safety measures, etc. For gases or gas mixtures not covered by these annexes the electric power equipment manufacturer should provide the information needed, following the structure of these annexes. Such gases or gas mixtures should also be described in a next edition or in amendments to this edition.
NOTE 1 For the use of this document, high-voltage (HV) is defined as the rated voltage above 1 000 V. However, the term medium-voltage (MV) is commonly used for distribution systems with voltages above 1 kV and generally applied up to and including 52 kV.
NOTE 2 Throughout this standard, the term "pressure" stands for "absolute pressure".
NOTE 3 Reference is also made to (Cigré Brochure 802, 2020).
NOTE 4 For further details on gases, e.g. ecotoxicology, also refer to the chemical database ECHA (www.echa.europa.eu), which takes the actual volume band into consideration.
NOTE 5 When reference to circuit-breakers is made, only gas circuit-breakers are of interest. When vacuum circuit breakers are of interest, they are explicitly mentioned.

  • Standard
    241 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    241 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-100:2021/AC:2022(Corrigendum)
High-voltage switchgear and controlgear - Part 100: Alternating-current circuit-breakers (IEC 62271-100:2021/COR2:2022)
EN IEC 62271-100:2021/AC:2022-09

IEC Corrected Version

  • Corrigendum
    6 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    6 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-203:2022(Main)
High-voltage switchgear and controlgear - Part 203: AC gas-insulated metal-enclosed switchgear for rated voltages above 52 kV (IEC 62271-203:2022)
EN IEC 62271-203:2022

This part of IEC 62271 specifies requirements for gas-insulated metal-enclosed switchgear in which the insulation is obtained, at least partly, by an insulating gas or gas mixture other than air at atmospheric pressure, for alternating current of rated voltages above 52 kV, for indoor and outdoor installation, and for service frequencies up to and including 60 Hz.
For the purpose of this standard, the terms "GIS" and "switchgear" are used for "gas-insulated metal-enclosed switchgear".
The gas-insulated metal-enclosed switchgear covered by this standard consists of individual components intended to be directly connected together and able to operate only in this manner.
This standard completes and amends, if necessary, the various relevant standards applying to the individual components constituting GIS.

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-212:2022(Main)
High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Substation (CEADS) for AC voltages up to 52 kV (IEC 62271-212:2022)
EN IEC 62271-212:2022

This part of IEC 62271 specifies the service conditions, rated characteristics, general structural
requirements and test methods of the assemblies of the main electrical functional units of a
high-voltage transformer substation, duly interconnected, for AC voltages up to and including
52 kV on the high-voltage side and service frequency 50 Hz or 60 Hz. The CEADS is
cable-connected to the high-voltage network for indoor and outdoor applications of restricted
access.
A CEADS as defined in this document is designed and tested to be a single product with a
single serial number and one set of documentation.
The functions of a CEADS are:
– high-voltage/high-voltage or high-voltage/low-voltage transformation;
and some or all the following:
– switching and control for the operation of the high-voltage circuit(s);
– switching and control for the operation of the low-voltage circuit(s);
– protection of the power transformer functional unit.
The main functions are integrated in the following functional units:
– high-voltage functional unit;
– power transformer functional unit;
– low-voltage functional unit.
NOTE For the purpose of this document a self-protected transformer is not considered as a CEADS, but as a
functional unit, designed and type tested to its own product standard IEC 60076-13:2006.

  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-202:2022(Main)
High-voltage switchgear and controlgear - Part 202: AC prefabricated substations for rated voltages above 1 kV and up to and including 52 kV (IEC 62271-202:2022)
EN IEC 62271-202:2022

This part of IEC 62271 specifies the service conditions, rated characteristics, general structural requirements and test methods of enclosed high-voltage prefabricated substations. These prefabricated substations are cable-connected to AC high-voltage networks with highest operating voltage up to and including 52 kV and power frequencies up to and including 60 Hz. They can be manually operated from inside (walk-in type) or from outside (non-walk-in type).They are designed for outdoor installation at locations with public accessibility and where protection of personnel is provided.
These prefabricated substations can be situated at ground level or partially or completely below ground level. The last are also called underground prefabricated substations.
In general, two types of prefabricated substations are considered in this standard:
- high-voltage switching prefabricated substations;
- high-voltage/low-voltage transformer prefabricated substations (step-up and step-down).
A high-voltage switching prefabricated substation comprises an enclosure containing in general the following electrical components:
- high-voltage switchgear and controlgear;
- auxiliary equipment and circuits.
A high-voltage/low-voltage transformer prefabricated substation comprises an enclosure containing in general the following electrical components:
- power transformers;
- high-voltage and low-voltage switchgear and controlgear;
- high-voltage and low-voltage interconnections;
- auxiliary equipment and circuits.
However, relevant provisions of this standard are applicable to designs where not all these electrical components exist (for example, a prefabricated substation consisting of power transformer and low-voltage switchgear and controlgear).
The listed electrical components of a high-voltage/low-voltage transformer prefabricated substation can be incorporated in the prefabricated substation either as separate components or as an assembly type CEADS according to IEC 62271-212.
This standard covers only designs using natural ventilation. However, relevant provisions of this standard are applicable to designs using other means of ventilation except the rated power of the prefabricated substation and associated class of enclosure (see 5.101), the continuous current tests (see 7.5) and all temperature rise related requirements, which would require an agreement between manufacturer and user.
NOTE IEC 61936-1 [1] provides general rules for the design and erection of high-voltage power installations. As well, it specifies additional requirements for the external connections, erection and operation at the place of installation of high-voltage prefabricated substations compliant with IEC 62271-202, which are regarded as a component of such installation. Non-prefabricated high-voltage substations, 483 are generally covered by IEC 61936-1 [1].

  • Standard
    124 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-204:2022(Main)
High-voltage switchgear and controlgear - Part 204: Rigid gas-insulated transmission lines for rated voltage above 52 kV (IEC 62271-204:2022)
EN IEC 62271-204:2022

This part of IEC 62271 applies to rigid HV gas-insulated transmission lines (GIL) in which the insulation is obtained, at least partly, by a non-corrosive insulating gas, other than air at atmospheric pressure, for alternating current of rated voltages above 52 kV, and for service frequencies up to and including 60 Hz. It is intended that this international standard shall be used where the provisions of IEC 62271-203 do not cover the application of GIL (see Note 3).
At each end of the HV gas-insulated transmission line, a specific element may be used for the connection between the HV gas-insulated transmission line and other equipment like bushings, power transformers or reactors, cable boxes, metal-enclosed surge arresters, voltage transformers or GIS, covered by their own specification.
Unless otherwise specified, the HV gas-insulated transmission line is designed to be used under normal service conditions.
Note 1 to entry: In this international standard, the term "HV gas-insulated transmission line" is abbreviated to "GIL".
Note 2 to entry: In this international standard, the word "gas" means gas or gas mixture, as defined by the manufacturer.
Note 3 to entry: Examples of GIL applications are given:
- where all or part of the HV gas-insulated transmission line is directly buried; or
- where the HV gas-insulated transmission line is located, wholly or partly, in an area accessible to public; or
- where the HV gas-insulated transmission line is long (typically longer than to 500 m) and the typical gas compartment length exceeds the common practice of GIS technology.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-102:2018/A1:2022(Amendment)
High-voltage switchgear and controlgear - Part 102: Alternating current disconnectors and earthing switches (IEC 62271-102:2018/AMD1:2022)
EN IEC 62271-102:2018/A1:2022
  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62271-209:2019/A1:2022(Amendment)
High-voltage switchgear and controlgear - Part 209: Cable connections for gasinsulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations (IEC 62271-209:2019/AMD1:2022)
EN IEC 62271-209:2019/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day