SIST EN 60684-3-212:2006
(Main)Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 212: Heat-shrinkable polyolefin sleevings
Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 212: Heat-shrinkable polyolefin sleevings
This standard gives the requirements for four types of heat-shrinkable polyolefin sleevings suitable for use at temperatures up to 135 C. Type A Flame retarded, shrink ratio 2:1, Type B Not flame retarded, shrink ration 2:1, Type C Flame retarded, shrink ratio 3:1, Type D Not flame retarded shrink ratio 3:1
Isolierschläuche -- Teil 3: Anforderungen für einzelne Schlauchtypen -- Blatt 212: Polyolefin-Wärmeschrumpfschläuche
Gaines isolantes souples -- Partie 3: Spécifications pour types particuliers de gaines -- Feuille 212: Gaines thermorétractables en polyoléfine
L'IEC 60684-3-212:2005 donne les exigences pour quatre types de gaines thermorétractables en polyoléfine adaptées à une utilisation à des températures allant jusqu'à 135 °C.
Type A: retardatrices de flamme, rapport de rétreint 2:1,
Type B: non retardatrices de flamme, rapport de rétreint 2:1,
Type C: retardatrices de flamme, rapport de rétreint 3:1,
Type D: non retardatrices de flamme, rapport de rétreint 3:1. Cette deuxième édition annule et remplace la première édition publiée en 1998 et constitue une révision technique. Cette édition comprend les modifications significatives suivantes par rapport à l'édition précédente: Remplacement de la méthode d'essai d'endurance thermique conformément à la CEI 60216 par un essai de vieillissement de longue durée, c'est-à-dire 3 000 h à la température maximale recommandée pour un usage adapté, en vue de fournir des données d'essai thermiques dans une échelle de temps exploitable.
Mots clés: gaines thermorétractables en polyoléfine
Gibke izolacijske cevi – 3. del: Specifikacije posameznih vrst cevi – 212. list: Toplotno skrčljive poliolefinske cevi (IEC 60684-3-312:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60684-3-212:2006
STANDARD
julij 2006
Gibke izolacijske cevi – 3. del: Specifikacije posameznih vrst cevi – 212. list:
Toplotno skrčljive poliolefinske cevi (IEC 60684-3-312:2005)
Flexible insulating sleeving – Part 3: Specifications for individual types of sleeving –
Sheet 212: Heat-shrinkable polyolefin sleevings (IEC 60684-3-312:2005)
ICS 29.035.20 Referenčna številka
SIST EN 60684-3-212:2006(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 60684-3-212
NORME EUROPÉENNE
February 2006
EUROPÄISCHE NORM
ICS 29.035.20 Supersedes EN 60684-3-212:1998, EN 60684-3-213:1999,
EN 60684-3-217:1998 and EN 60684-3-218:1998
English version
Flexible insulating sleeving
Part 3: Specifications for individual types of sleeving
Sheet 212: Heat-shrinkable polyolefin sleevings
(IEC 60684-3-212:2005)
Gaines isolantes souples Isolierschläuche
Partie 3: Spécifications Teil 3: Anforderungen
pour types particuliers de gaines für einzelne Schlauchtypen
Feuille 212: Gaines thermorétractables Blatt 212: Polyolefin-
en polyoléfine Wärmeschrumpfschläuche
(CEI 60684-3-212:2005) (IEC 60684-3-212:2005)
This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-212:2006 E
---------------------- Page: 2 ----------------------
EN 60684-3-212:2006 - 2 -
Foreword
The text of document 15/229/FDIS, future edition 2 of IEC 60684-3-212, prepared by IEC TC 15,
Standards on specifications for electrical insulating materials, was submitted to the IEC-CENELEC
parallel vote and was approved by CENELEC as EN 60684-3-212 on 2005-11-01.
This European Standard supersedes EN 61684-3-212:1998, EN 60684-3-213:1999,
EN 60684-3-217:1998 and EN 60684-3-218:1998.
This European Standard includes the following significant changes with regards to EN 60684-3-212:1998:
Replacement of the thermal endurance test method according to EN 60216 with a long term ageing test,
i.e. 3 000 h at the recommended maximum temperature found suitable for use, to provide safe thermal
test data within a workable time scale.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-11-01
This European Standard makes reference to International Standards. Where the International Standard
referred to has been endorsed as a European Standard or a home-grown European Standard exists, this
European Standard shall be applied instead. Pertinent information can be found on the CENELEC web
site.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-212:2005 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
INTERNATIONAL IEC
STANDARD 60684-3-212
Second edition
2005-11
Flexible insulating sleeving –
Part 3:
Specifications for individual types of sleeving –
Sheet 212: Heat-shrinkable polyolefin sleevings
IEC 2005 Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale M
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue
---------------------- Page: 4 ----------------------
– 2 – 60684-3-212 IEC:2005(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Designation .7
4 Conditions of test.7
5 Requirements .7
6 Sleeving conformance.7
7 Breakdown voltage .11
Table 1 – Dimensional and mass requirements for Types A and B .8
Table 2 – Dimensional and mass requirements for Types C and D.8
Table 3 – Property requirements .9
Table 4 – Requirements for breakdown voltage .11
Table 5 – Resistance to selected fluids.12
Table 6 – Additional property requirements.12
---------------------- Page: 5 ----------------------
60684-3-212 IEC:2005(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving –
Sheet 212: Heat-shrinkable polyolefin sleevings
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60684-3-212 has been prepared by IEC technical committee 15:
Standards on specifications for electrical Insulating materials.
This second edition cancels and replaces the first edition published in 1998, and constitutes a
technical revision.
This edition includes the following significant changes with regards to the previous edition:
Replacement of the thermal endurance test method according to IEC 60216 with a long term
ageing test, i.e. 3 000 h at the recommended maximum temperature found suitable for use, to
provide safe thermal test data within a workable time scale.
---------------------- Page: 6 ----------------------
– 4 – 60684-3-212 IEC:2005(E)
The text of this standard is based on the following documents:
FDIS Re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.