SIST EN IEC 62271-215:2021
(Main)High-voltage switchgear and controlgear - Part 215: Phase comparator used with VDIS (IEC 62271-215:2021)
High-voltage switchgear and controlgear - Part 215: Phase comparator used with VDIS (IEC 62271-215:2021)
This part of IEC 62271 is applicable to phase comparators designed to be plugged into the
testing points of a voltage detecting and indicating system (VDIS) according to IEC 62271-213,
to give an indication of the result of a phase comparison.
The main usage is to provide clear evidence of the phase relationship between two energized
parts of a high-voltage network, at the same nominal voltage and frequency before coupling
them.
This document or parts of the document can also be applied to the phase comparison function
of other devices connected to the VDIS upon agreement between manufacturer and user.
This document does not cover phase comparators to be used directly on bare parts of live
electrical installation at the nominal voltage of the networks. These phase comparators are
covered by IEC 61481-1 and IEC 61481-2.
Hochspannungs-Schaltgeräte und -Schaltanlagen – Teil 215: Phasenvergleicher (IEC 62271-215:2021)
Appareillage à haute tension - Partie 215: Comparateur de phase utilisé avec un VDIS (IEC 62271-215:2021)
L’IEC 62271-215:2021 s’applique aux comparateurs de phase conçus pour être enfichés dans les points de contrôle d’un système détecteur et indicateur de tension (VDIS), conformément à l’IEC 62271-213, pour donner une indication du résultat d’une comparaison de phase.
La principale utilisation est de fournir une preuve indiscutable de la concordance de phase entre deux parties actives d’un réseau à haute tension, qui sont à la même tension nominale et la même fréquence nominale, avant de les coupler.
Cette première édition annule et remplace la première édition de l’IEC 61243-5 parue en 1997 et la première édition de l’IEC 62271-206 parue en 2011. Cette édition est issue de la fusion de l’IEC 61243-5 et de l’IEC 62271-206.
Cette édition inclut les modifications techniques majeures suivantes par rapport aux éditions précédentes de l’IEC 61243-5 et l’IEC 62271-206:
- le document n’inclut pas les comparateurs de phase spécifiques (SPC- specific phase comparator) définis dans l’IEC 61243-5, qui étaient spécifiques aux constructeurs, et reprend les principes techniques du comparateur de phase universel (UPC – universal phase comparator) pour les VIDS de tous les constructeurs;
- le comparateur de phase pour un fonctionnement à raccordement séquentiel est instauré afin de faciliter la mise en œuvre de la comparaison de phase des grands panneaux MT.
Visokonapetostne stikalne in krmilne naprave - 215. del: Fazni primerjalnik, uporabljen z VDIS (IEC 62271-215:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62271-215:2021
01-november-2021
Visokonapetostne stikalne in krmilne naprave - 215. del: Fazni primerjalnik,
uporabljen z VDIS (IEC 62271-215:2021)
High-voltage switchgear and controlgear - Part 215: Phase comparator used with VDIS
(IEC 62271-215:2021)
Hochspannungs-Schaltgeräte und -Schaltanlagen – Teil 215: Phasenvergleicher (IEC
62271-215:2021)
Appareillage à haute tension - Partie 215: Comparateur de phase utilisé avec un VDIS
(IEC 62271-215:2021)
Ta slovenski standard je istoveten z: EN IEC 62271-215:2021
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN IEC 62271-215:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62271-215:2021
---------------------- Page: 2 ----------------------
SIST EN IEC 62271-215:2021
EUROPEAN STANDARD EN IEC 62271-215
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2021
ICS 13.260; 29.130.10; 29.240.20
English Version
High-voltage switchgear and controlgear - Part 215: Phase
comparator used with VDIS
(IEC 62271-215:2021)
Appareillage à haute tension - Partie 215: Comparateur de Hochspannungs-Schaltgeräte und -Schaltanlagen - Teil
phase utilisé avec un VDIS 215: Phasenvergleicher in Kombination mit einem
(IEC 62271-215:2021) Spannungsprüf- und -anzeigegerät
(IEC 62271-215:2021)
This European Standard was approved by CENELEC on 2021-08-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62271-215:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62271-215:2021
EN IEC 62271-215:2021 (E)
European foreword
The text of document 17C/788/FDIS, future edition 1 of IEC 62271-215, prepared by SC 17C
“Assemblies” of IEC/TC 17 “High-voltage switchgear and controlgear” was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN IEC 62271-215:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–05–03
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024–08–03
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62271-215:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61481-1:2014 NOTE Harmonized as EN 61481-1:2014 (not modified)
IEC 61481-2:2014 NOTE Harmonized as EN 61481-2:2014 (not modified)
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62271-215:2021
EN IEC 62271-215:2021 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60060-1 - High-voltage test techniques - Part 1: EN 60060-1 -
General definitions and test requirements
IEC 60068-2-1 2007 Environmental testing - Part 2–1: Tests - EN 60068-2-1 2007
Test A: Cold
IEC 60068-2-2 2007 Environmental testing - Part 2–2: Tests - EN 60068-2-2 2007
Test B: Dry heat
IEC 60068-2-6 - Environmental testing - Part 2–6: Tests - EN 60068-2-6 -
Test Fc: Vibration (sinusoidal)
IEC 60068-2-31 - Environmental testing - Part 2–31: Tests - EN 60068-2-31 -
Test Ec: Rough handling shocks, primarily
for equipment-type specimens
IEC 60068-2-38 - Environmental testing - Part 2–38: Tests - EN IEC 60068-2-38 -
Test Z/AD: Composite
temperature/humidity cyclic test
IEC 60417 - Graphical symbols for use on equipment - -
IEC 60529 - Degrees of protection provided by - -
enclosures (IP Code)
IEC 61000-4-2 - Electromagnetic compatibility (EMC) - Part EN 61000-4-2 -
4–2: Testing and measurement techniques
- Electrostatic discharge immunity test
IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part EN IEC 61000-4-3 -
4–3: Testing and measurement techniques
- Radiated, radio-frequency,
electromagnetic field immunity test
IEC 61000-4-5 - Electromagnetic compatibility (EMC) - Part EN 61000-4-5 -
4–5: Testing and measurement techniques
- Surge immunity test
IEC 62262 - Degrees of protection provided by EN 62262 -
enclosures for electrical equipment against
external mechanical impacts (IK code)
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62271-215:2021
EN IEC 62271-215:2021 (E)
IEC 62271-1 - High-voltage switchgear and controlgear - EN 62271-1 -
Part 1: Common specifications
IEC 62271-213 - High-voltage switchgear and controlgear - - -
Part 213: Voltage detecting and indicating
system
4
---------------------- Page: 6 ----------------------
SIST EN IEC 62271-215:2021
IEC 62271-215
®
Edition 1.0 2021-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
High-voltage switchgear and controlgear –
Part 215: Phase comparator used with VDIS
Appareillage à haute tension –
Partie 215: Comparateur de phase utilisé avec un VDIS
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 13.260; 29.130.10; 29.240.20 ISBN 978-2-8322-9892-3
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62271-215:2021
– 2 – IEC 62271-215:2021 IEC 2021
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 Normal and special service conditions . 13
4.1 Normal service conditions . 13
4.2 Special service conditions . 13
5 Ratings . 13
6 Design and construction . 13
6.1 General . 13
6.2 Parts of phase comparator . 13
6.3 Phase comparator description . 14
6.3.1 General . 14
6.3.2 Phase comparator for simultaneous connected operation . 14
6.3.3 Phase comparator for sequential connected operation . 15
6.4 Connection to VDIS . 15
6.5 Indication and perceptibility . 16
6.5.1 General . 16
6.5.2 Phase comparator providing only one active signal . 17
6.5.3 Phase comparator providing two or more active signals . 17
6.5.4 Indication of phase comparator with built-in power supply . 17
6.5.5 Indication of sequential phase comparators . 17
6.5.6 Response time of indication . 17
6.5.7 Perceptibility . 18
6.6 Phase comparator with built-in power supply . 18
6.7 Testing element . 18
6.8 Additional functions. 18
6.9 Probes . 18
6.10 Settings . 19
6.11 Tolerance of rated frequency . 20
6.12 Frequency shift of phase comparators with sequential operation . 20
6.13 Degree of protection (IP code) . 20
6.14 Climatic requirements . 20
6.14.1 General . 20
6.14.2 Temperature . 20
6.14.3 Composite temperature/humidity . 20
6.15 Mechanical requirements . 20
6.15.1 General . 20
6.15.2 Assembly . 20
6.15.3 Vibrations . 20
6.15.4 Mechanical impact (IK code) . 21
6.15.5 Fall . 21
6.16 Electromagnetic compatibility . 21
6.16.1 General . 21
6.16.2 Electrostatic discharge . 21
---------------------- Page: 8 ----------------------
SIST EN IEC 62271-215:2021
IEC 62271-215:2021 IEC 2021 – 3 –
6.16.3 Immunity against radiated electromagnetic fields . 21
6.17 Dielectric strength . 21
6.17.1 General . 21
6.17.2 Lightning impulse withstand voltage. 21
6.17.3 Power-frequency withstand voltage . 21
6.17.4 Insulation withstand voltage . 22
6.18 Marking . 22
7 Type tests . 22
7.1 General . 22
7.1.1 Information to be included in the type test report . 22
7.1.2 Test conditions . 22
7.1.3 List of tests . 23
7.2 Test values . 24
7.3 Inspection . 24
7.4 Dielectric tests . 24
7.4.1 General . 24
7.4.2 Lightning impulse voltage test. 24
7.4.3 Power-frequency voltage test . 25
7.4.4 Voltage withstand test of the phase comparator . 25
7.5 Indication and perceptibility . 25
7.5.1 Test set-up and procedure for clear indication . 25
7.5.2 Test for correct phase relationship . 26
7.5.3 Test for incorrect phase relationship . 27
7.5.4 Absence of voltage on one VDIS . 27
7.5.5 Absence of voltage on both VDIS . 27
7.5.6 Test of impedance of the phase comparator . 27
7.6 Test for maximum phase rotation . 28
7.6.1 Test set-up for maximum phase rotation with capacitive coupling
element . 28
7.6.2 Test set-up for maximum phase rotation with resistive coupling element . 28
7.6.3 Test result for maximum phase rotation . 29
7.7 Tolerance of rated frequency . 29
7.7.1 Test set-up . 29
7.7.2 Test procedure . 30
7.8 Frequency shift for sequential operation phase comparator. 30
7.8.1 Test set-up . 30
7.8.2 Test procedure . 30
7.9 Response time . 30
7.9.1 Test set-up . 30
7.9.2 Procedure . 31
7.10 Clear perceptibility of visual indication . 31
7.10.1 General . 31
7.10.2 Test set-up . 31
7.10.3 Procedure . 32
7.11 Test for frequency selection (where relevant) . 32
7.12 Temperature dependence of indication . 32
7.13 Composite temperature/humidity cyclic test . 33
7.14 Degree of protection (IP code) . 33
7.15 Vibrations . 33
---------------------- Page: 9 ----------------------
SIST EN IEC 62271-215:2021
– 4 – IEC 62271-215:2021 IEC 2021
7.16 Mechanical impact (IK code) . 33
7.17 Fall . 33
7.18 Electrostatic discharge . 33
7.19 Radiated electromagnetic fields . 34
7.20 Phase comparator when built-in power supply is exhausted . 34
7.20.1 Preparation . 34
7.20.2 Operation . 34
7.21 Efficiency of testing element . 34
7.21.1 Preparation . 34
7.21.2 Operation . 34
7.22 Durability of marking . 35
8 Routine tests . 35
9 Guide to the selection of phase comparator (informative) . 35
10 Information to be given with enquiries, tenders and orders (informative) . 35
10.1 General . 35
10.2 Information with enquiries and orders . 35
10.3 Information with tenders . 36
11 Transport, storage, installation, operation, maintenance and instructions for use . 36
11.1 General . 36
11.2 Instructions for use . 36
11.3 Maintenance . 37
11.3.1 General . 37
11.3.2 Maintenance period . 37
11.3.3 Maintenance by testing . 37
12 Safety . 37
13 Influence of the phase comparator on the environment . 37
Annex A (informative) Example of design . 38
A.1 General . 38
A.2 Wireless connection . 38
Annex B (informative) Example of use . 39
Bibliography . 40
Figure 1 – Example of typical structure of simultaneous operating phase comparator . 14
Figure 2 – Simultaneous connected operation with two earth connections . 14
Figure 3 – Simultaneous connected operation with one earth connection . 15
Figure 4 – Example of typical structure of sequential operating phase comparator . 15
Figure 5 – Sequential connected operation . 15
Figure 6 – Classes of phase comparators with only positive angle values shown . 16
Figure 7 – Plug size and design without insulation shield . 19
Figure 8 – Plug size and design with insulation shield . 19
Figure 9 – Connection of test set-up for clear indication . 26
Figure 10 – Connection of test set-up for clear indication for sequential operation . 26
Figure 11 – Connection of test set-up for phase rotation . 28
Figure 12 – Connection of test set-up for phase rotation for sequential operation . 28
Figure 13 – Connection of test set-up for phase rotation . 29
Figure 14 – Connection of test set-up for phase rotation for sequential operation . 29
---------------------- Page: 10 ----------------------
SIST EN IEC 62271-215:2021
IEC 62271-215:2021 IEC 2021 – 5 –
Figure 15 – Test set-up for perceptibility of visual indication . 32
Figure A.1 – Phase comparator with a wireless connection . 38
Table 1 – Sequence of type tests . 23
Table 2 – List of type tests without sequence . 24
Table 3 – List of routine tests . 35
Table B.1 – Results and conclusions of a cable checking. 39
---------------------- Page: 11 ----------------------
SIST EN IEC 62271-215:2021
– 6 – IEC 62271-215:2021 IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Part 215: Phase comparator used with VDIS
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62271-215 has been prepared by sub-committee SC17C:
Assemblies, of IEC technical committee 17: High-voltage switchgear and controlgear in liaison
with IEC TC 78: Live working.
This first edition cancels and replaces the first edition of IEC 61243-5 published in 1997 and
the first edition of IEC 62271-206 published in 2011. This edition constitutes a merging of the
content of IEC 61243-5 and IEC 62271-206.
This edition includes the following significant technical changes with respect to the previous
editions of IEC 61243-5 and IEC 62271-206:
a) the document does not in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.