Direct acting indicating analogue electrical measuring instruments and their accessories - Part 5: Special requirements for phase meters, power factor meters and synchroscopes (IEC 60051-5:2017)

This part of IEC 60051 applies to direct acting indicating phase meters, power factor meters
and synchroscopes having an analogue display.
This document also applies to non-interchangeable accessories (as defined in 3.1.23 of
IEC 60051-1:2016) used with phase meters, power factor meters and synchroscopes.
This document also applies to a phase meter or power factor meter whose scale marks do not
correspond directly to its electrical input quantity, provided that the relationship between them
is known.

Direkt wirkende anzeigende elektrische Meßgeräte und ihr Zubehör - Meßgeräte mit Skalenanzeige - Teil 5: Spezielle Anforderungen für Phasenverschiebungswinkel-Meßgeräte, Leitstungsfaktor- Meßgeräte und Synchronoskope (IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à action directe et leurs accessoires - Partie 5: Prescriptions particulières pour les phasemètres, les indicateurs de facteur de puissance et les synchronoscopes (IEC 60051-5:2017)

L'IEC 60051-5:2017 s'applique aux phasemètres, aux appareils de mesure de facteur de puissance et aux synchronoscopes indicateurs analogiques à action directe. Le présent document s'applique également aux accessoires non interchangeables (définis en 3.1.23 de l'IEC 60051-1:2016) utilisés avec les phasemètres, les appareils de mesure de facteur de puissance et les synchronoscopes. Le présent document s'applique également aux phasemètres ou aux appareils de mesure de facteur de puissance dont les repères d'échelle ne correspondent pas directement à la grandeur électrique appliquée à l'entrée de l'appareil, à condition que la relation entre celles-ci soit connue. Cette cinquième édition annule et remplace la quatrième édition parue en 1985. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) mise à jour du contenu en fonction des nouvelles éditions de l'IEC 60051-1 et de l'IEC 60051-9; b) ajout de l'Annexe A pour spécifier la classification des non-conformités des éléments d'essai.

Neposredni kazalni analogni električni merilni instrumenti in njihov pribor - 5. del: Posebne zahteve za merilnike faze, merilnike faktorja moči in za sinhroskope (IEC 60051-5:2017)

Ta del standarda IEC 60051 se uporablja za neposredne kazalne merilnike faze, merilnike faktorja moči in sinhroskope z analognim prikazom.
Ta dokument se uporablja tudi za nezamenljiv pribor (kot je določen v točki 3.1.23 standarda IEC 60051-1:2016) merilnikov faze, merilnikov faktorja moči in sinhroskopov.
Ta dokument se uporablja tudi za merilnik faze ali merilnik faktorja moči, pri katerem oznake na skali ne ustrezajo neposredno vhodni električni količini, če je razmerje med njima znano.

General Information

Status
Published
Publication Date
07-May-2018
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
23-Mar-2018
Due Date
28-May-2018
Completion Date
08-May-2018

RELATIONS

Buy Standard

Standard
SIST EN IEC 60051-5:2018
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
SIST EN IEC 60051-5:2018
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
SIST EN 60051-5:2018
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN IEC 60051-5:2018
01-junij-2018
Nadomešča:
SIST EN 60051-5:1995

Neposredni kazalni analogni električni merilni instrumenti in njihov pribor - 5. del:

Posebne zahteve za merilnike faze, merilnike faktorja moči in za sinhroskope (IEC

60051-5:2017)

Direct acting indicating analogue electrical measuring instruments and their accessories

- Part 5: Special requirements for phase meters, power factor meters and synchroscopes

(IEC 60051-5:2017)
Direkt wirkende anzeigende elektrische Meßgeräte und ihr Zubehör - Meßgeräte mit
Skalenanzeige - Teil 5: Spezielle Anforderungen für Phasenverschiebungswinkel-
Meßgeräte, Leitstungsfaktor- Meßgeräte und Synchronoskope (IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à action directe et leurs

accessoires - Partie 5: Prescriptions particulières pour les phasemètres, les indicateurs

de facteur de puissance et les synchronoscopes (IEC 60051-5:2017)
Ta slovenski standard je istoveten z: EN IEC 60051-5:2018
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
SIST EN IEC 60051-5:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60051-5:2018
---------------------- Page: 2 ----------------------
SIST EN IEC 60051-5:2018
EUROPEAN STANDARD EN IEC 60051-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 17.220.20 Supersedes EN 60051-5:1989
English Version
Direct acting indicating analogue electrical measuring
instruments and their accessories - Part 5: Special requirements
for phase meters, power factor meters and synchroscopes
(IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à Direkt wirkende anzeigende elektrische Meßgeräte und ihr

action directe et leurs accessoires - Partie 5: Exigences Zubehör - Meßgeräte mit Skalenanzeige - Teil 5: Spezielle

particulières pour les phasemètres, les appareils de mesure Anforderungen für Phasenverschiebungswinkel-Meßgeräte,

de facteur de puissance et les synchronoscopes Leitstungsfaktor- Meßgeräte und Synchronoskope

(IEC 60051-5:2017) (IEC 60051-5:2017)

This European Standard was approved by CENELEC on 2018-01-19. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN IEC 60051-5:2018 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60051-5:2018
EN IEC 60051-5:2018 (E)
European foreword

The text of document 85/581/CDV, future edition 5 of IEC 60051-5, prepared by IEC/TC 85

"Measuring equipment for electrical and electromagnetic quantities" was submitted to the IEC-

CENELEC parallel vote and approved by CENELEC as EN IEC 60051-5:2018.
The following dates are fixed:
(dop) 2018-10-19
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2021-01-19
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60051-5:1989.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directives.

For the relationship with EU Directives see informative Annex ZZ, which is an integral part of this

document.
Endorsement notice

The text of the International Standard IEC 60051-5:2017 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

1 2
IEC 60051-9 NOTE Harmonized as EN 60051-9 .
To be published. Stage at the time of publication: IEC CDV 60051-9:2018.
To be published. Stage at the time of publication: prEN 60051-9:2018.
---------------------- Page: 4 ----------------------
SIST EN IEC 60051-5:2018
EN IEC 60051-5:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:

www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60051-1 2016 Direct acting indicating analogue electrical EN 60051-1 2017
measuring instruments and their
accessories – Part 1: Definitions and
general requirements common to all parts
---------------------- Page: 5 ----------------------
SIST EN IEC 60051-5:2018
---------------------- Page: 6 ----------------------
SIST EN IEC 60051-5:2018
IEC 60051-5
Edition 5.0 2017-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Direct acting indicating analogue electrical measuring instruments and their
accessories –
Part 5: Special requirements for phase meters, power factor meters and
synchroscopes
Appareils mesureurs électriques indicateurs analogiques à action directe et
leurs accessoires –
Partie 5: Exigences particulières pour les phasemètres, les appareils de mesure
de facteur de puissance et les synchronoscopes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20 ISBN 978-2-8322-5187-4

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60051-5:2018
– 2 – IEC 60051-5:2017 © IEC 2017
CONTENTS

FOREWORD ........................................................................................................................... 4

INTRODUCTION ..................................................................................................................... 6

1 Scope .............................................................................................................................. 7

2 Normative references ...................................................................................................... 7

3 Terms and definitions ...................................................................................................... 7

4 Description, classification and compliance ....................................................................... 7

4.1 Description ............................................................................................................. 7

4.2 Classification .......................................................................................................... 7

4.3 Compliance with the requirements of this standard ................................................. 7

5 Requirements .................................................................................................................. 8

5.1 Reference conditions .............................................................................................. 8

5.2 Limits of intrinsic uncertainty, fiducial value ............................................................ 8

5.2.1 Limits of intrinsic uncertainty ........................................................................... 8

5.2.2 Correspondence between intrinsic uncertainty and accuracy class .................. 8

5.2.3 Fiducial value .................................................................................................. 8

5.3 Nominal range of use and variations ....................................................................... 8

5.3.1 Nominal range of use ....................................................................................... 8

5.3.2 Limits of variations........................................................................................... 9

5.3.3 Conditions for the determination of variations ................................................ 10

5.4 Operating uncertainty, overall system uncertainty and variations .......................... 10

5.5 Electrical requirements ......................................................................................... 10

5.5.1 Electrical safety requirements ........................................................................ 10

5.5.2 Self-heating ................................................................................................... 10

5.5.3 Permissible overloads .................................................................................... 10

5.5.4 Limiting range of temperature ........................................................................ 11

5.5.5 Deviation from zero ....................................................................................... 11

5.5.6 Electromagnetic compatibility (EMC) ............................................................. 11

5.5.7 Special requirements for synchroscopes ........................................................ 12

5.6 Constructional requirements ................................................................................. 12

5.6.1 General constructional requirements ............................................................. 12

5.6.2 Damping ........................................................................................................ 12

5.6.3 Sealing to prevent access .............................................................................. 12

5.6.4 Scales ........................................................................................................... 12

5.6.5 Stopper.......................................................................................................... 12

5.6.6 Preferred values ............................................................................................ 12

5.6.7 Adjusters, mechanical and/or electrical .......................................................... 13

5.6.8 Effects of vibration and shock ........................................................................ 13

5.6.9 Degrees of protection provided by enclosure ................................................. 13

5.6.10 Terminals ...................................................................................................... 13

6 Information, markings and symbols ................................................................................ 13

6.1 Information ........................................................................................................... 13

6.2 Markings, symbols and their locations ................................................................... 13

6.3 Markings relating to the reference values and nominal ranges of use of

influence quantities ............................................................................................... 13

6.4 The symbols for marking instruments and accessories .......................................... 13

6.5 Markings and symbols for terminals ...................................................................... 13

---------------------- Page: 8 ----------------------
SIST EN IEC 60051-5:2018
IEC 60051-5:2017 © IEC 2017 – 3 –

6.5.1 Requirements for markings ............................................................................ 13

6.5.2 Earthing (grounding) terminals ....................................................................... 13

6.5.3 Measuring circuit terminals ............................................................................ 14

6.5.4 Special markings for terminals ....................................................................... 14

6.6 Instructions for use ............................................................................................... 14

7 Package ........................................................................................................................ 14

8 Test rules ...................................................................................................................... 14

Annex A (normative) Nonconformity classification of tests ................................................... 15

Bibliography .......................................................................................................................... 16

Table 1 – Reference conditions and tolerances, additional to those given in Table 2 of

IEC 60051-1:2016, for testing purposes relating to the influence quantities ............................. 8

Table 2 – Limits of the nominal range of use and permissible variations in addition to

those given in Table 3 of IEC 60051-1:2016 ............................................................................ 9

Table 3 – Overloads of short duration ................................................................................... 11

Table A.1 – Nonconformity classification of tests .................................................................. 15

---------------------- Page: 9 ----------------------
SIST EN IEC 60051-5:2018
– 4 – IEC 60051-5:2017 © IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DIRECT ACTING INDICATING ANALOGUE ELECTRICAL
MEASURING INSTRUMENTS AND THEIR ACCESSORIES –
Part 5: Special requirements for phase meters,
power factor meters and synchroscopes
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60051-5 has been pr
...

SLOVENSKI STANDARD
SIST EN IEC 60051-5:2018
01-junij-2018
Nadomešča:
SIST EN 60051-5:1995

Neposredni kazalni analogni električni merilni instrumenti in njihov pribor - 5. del:

Posebne zahteve za merilnike faze, merilnike faktorja moči in za sinhroskope (IEC

60051-5:2017)

Direct acting indicating analogue electrical measuring instruments and their accessories

- Part 5: Special requirements for phase meters, power factor meters and synchroscopes

(IEC 60051-5:2017)
Direkt wirkende anzeigende elektrische Meßgeräte und ihr Zubehör - Meßgeräte mit
Skalenanzeige - Teil 5: Spezielle Anforderungen für Phasenverschiebungswinkel-
Meßgeräte, Leitstungsfaktor- Meßgeräte und Synchronoskope (IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à action directe et leurs

accessoires - Partie 5: Prescriptions particulières pour les phasemètres, les indicateurs

de facteur de puissance et les synchronoscopes (IEC 60051-5:2017)
Ta slovenski standard je istoveten z: EN IEC 60051-5:2018
ICS:
17.220.20 Merjenje električnih in Measurement of electrical
magnetnih veličin and magnetic quantities
SIST EN IEC 60051-5:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60051-5:2018
---------------------- Page: 2 ----------------------
SIST EN IEC 60051-5:2018
EUROPEAN STANDARD EN IEC 60051-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 17.220.20 Supersedes EN 60051-5:1989
English Version
Direct acting indicating analogue electrical measuring
instruments and their accessories - Part 5: Special requirements
for phase meters, power factor meters and synchroscopes
(IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à Direkt wirkende anzeigende elektrische Meßgeräte und ihr

action directe et leurs accessoires - Partie 5: Exigences Zubehör - Meßgeräte mit Skalenanzeige - Teil 5: Spezielle

particulières pour les phasemètres, les appareils de mesure Anforderungen für Phasenverschiebungswinkel-Meßgeräte,

de facteur de puissance et les synchronoscopes Leitstungsfaktor- Meßgeräte und Synchronoskope

(IEC 60051-5:2017) (IEC 60051-5:2017)

This European Standard was approved by CENELEC on 2018-01-19. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN IEC 60051-5:2018 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60051-5:2018
EN IEC 60051-5:2018 (E)
European foreword

The text of document 85/581/CDV, future edition 5 of IEC 60051-5, prepared by IEC/TC 85

"Measuring equipment for electrical and electromagnetic quantities" was submitted to the IEC-

CENELEC parallel vote and approved by CENELEC as EN IEC 60051-5:2018.
The following dates are fixed:
(dop) 2018-10-19
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2021-01-19
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60051-5:1989.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directives.

For the relationship with EU Directives see informative Annex ZZ, which is an integral part of this

document.
Endorsement notice

The text of the International Standard IEC 60051-5:2017 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

1 2
IEC 60051-9 NOTE Harmonized as EN 60051-9 .
To be published. Stage at the time of publication: IEC CDV 60051-9:2018.
To be published. Stage at the time of publication: prEN 60051-9:2018.
---------------------- Page: 4 ----------------------
SIST EN IEC 60051-5:2018
EN IEC 60051-5:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:

www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60051-1 2016 Direct acting indicating analogue electrical EN 60051-1 2017
measuring instruments and their
accessories – Part 1: Definitions and
general requirements common to all parts
---------------------- Page: 5 ----------------------
SIST EN IEC 60051-5:2018
---------------------- Page: 6 ----------------------
SIST EN IEC 60051-5:2018
IEC 60051-5
Edition 5.0 2017-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Direct acting indicating analogue electrical measuring instruments and their
accessories –
Part 5: Special requirements for phase meters, power factor meters and
synchroscopes
Appareils mesureurs électriques indicateurs analogiques à action directe et
leurs accessoires –
Partie 5: Exigences particulières pour les phasemètres, les appareils de mesure
de facteur de puissance et les synchronoscopes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20 ISBN 978-2-8322-5187-4

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 60051-5:2018
– 2 – IEC 60051-5:2017 © IEC 2017
CONTENTS

FOREWORD ........................................................................................................................... 4

INTRODUCTION ..................................................................................................................... 6

1 Scope .............................................................................................................................. 7

2 Normative references ...................................................................................................... 7

3 Terms and definitions ...................................................................................................... 7

4 Description, classification and compliance ....................................................................... 7

4.1 Description ............................................................................................................. 7

4.2 Classification .......................................................................................................... 7

4.3 Compliance with the requirements of this standard ................................................. 7

5 Requirements .................................................................................................................. 8

5.1 Reference conditions .............................................................................................. 8

5.2 Limits of intrinsic uncertainty, fiducial value ............................................................ 8

5.2.1 Limits of intrinsic uncertainty ........................................................................... 8

5.2.2 Correspondence between intrinsic uncertainty and accuracy class .................. 8

5.2.3 Fiducial value .................................................................................................. 8

5.3 Nominal range of use and variations ....................................................................... 8

5.3.1 Nominal range of use ....................................................................................... 8

5.3.2 Limits of variations........................................................................................... 9

5.3.3 Conditions for the determination of variations ................................................ 10

5.4 Operating uncertainty, overall system uncertainty and variations .......................... 10

5.5 Electrical requirements ......................................................................................... 10

5.5.1 Electrical safety requirements ........................................................................ 10

5.5.2 Self-heating ................................................................................................... 10

5.5.3 Permissible overloads .................................................................................... 10

5.5.4 Limiting range of temperature ........................................................................ 11

5.5.5 Deviation from zero ....................................................................................... 11

5.5.6 Electromagnetic compatibility (EMC) ............................................................. 11

5.5.7 Special requirements for synchroscopes ........................................................ 12

5.6 Constructional requirements ................................................................................. 12

5.6.1 General constructional requirements ............................................................. 12

5.6.2 Damping ........................................................................................................ 12

5.6.3 Sealing to prevent access .............................................................................. 12

5.6.4 Scales ........................................................................................................... 12

5.6.5 Stopper.......................................................................................................... 12

5.6.6 Preferred values ............................................................................................ 12

5.6.7 Adjusters, mechanical and/or electrical .......................................................... 13

5.6.8 Effects of vibration and shock ........................................................................ 13

5.6.9 Degrees of protection provided by enclosure ................................................. 13

5.6.10 Terminals ...................................................................................................... 13

6 Information, markings and symbols ................................................................................ 13

6.1 Information ........................................................................................................... 13

6.2 Markings, symbols and their locations ................................................................... 13

6.3 Markings relating to the reference values and nominal ranges of use of

influence quantities ............................................................................................... 13

6.4 The symbols for marking instruments and accessories .......................................... 13

6.5 Markings and symbols for terminals ...................................................................... 13

---------------------- Page: 8 ----------------------
SIST EN IEC 60051-5:2018
IEC 60051-5:2017 © IEC 2017 – 3 –

6.5.1 Requirements for markings ............................................................................ 13

6.5.2 Earthing (grounding) terminals ....................................................................... 13

6.5.3 Measuring circuit terminals ............................................................................ 14

6.5.4 Special markings for terminals ....................................................................... 14

6.6 Instructions for use ............................................................................................... 14

7 Package ........................................................................................................................ 14

8 Test rules ...................................................................................................................... 14

Annex A (normative) Nonconformity classification of tests ................................................... 15

Bibliography .......................................................................................................................... 16

Table 1 – Reference conditions and tolerances, additional to those given in Table 2 of

IEC 60051-1:2016, for testing purposes relating to the influence quantities ............................. 8

Table 2 – Limits of the nominal range of use and permissible variations in addition to

those given in Table 3 of IEC 60051-1:2016 ............................................................................ 9

Table 3 – Overloads of short duration ................................................................................... 11

Table A.1 – Nonconformity classification of tests .................................................................. 15

---------------------- Page: 9 ----------------------
SIST EN IEC 60051-5:2018
– 4 – IEC 60051-5:2017 © IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DIRECT ACTING INDICATING ANALOGUE ELECTRICAL
MEASURING INSTRUMENTS AND THEIR ACCESSORIES –
Part 5: Special requirements for phase meters,
power factor meters and synchroscopes
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60051-5 has been pr
...

SLOVENSKI STANDARD
SIST EN 60051-5:2018
01-junij-2018
1DGRPHãþD
SIST EN 60051-5:1995

1HSRVUHGQLND]DOQLDQDORJQLHOHNWULþQLPHULOQLLQVWUXPHQWLLQQMLKRYSULERUGHO

3RVHEQH]DKWHYH]DPHULOQLNHID]HPHULOQLNHIDNWRUMDPRþLLQ]DVLQKURVNRSH ,(&



Direct acting indicating analogue electrical measuring instruments and their accessories -

Part 5: Special requirements for phase meters, power factor meters and synchroscopes

(IEC 60051-5:2017)
Direkt wirkende anzeigende elektrische Meßgeräte und ihr Zubehör - Meßgeräte mit
Skalenanzeige - Teil 5: Spezielle Anforderungen für Phasenverschiebungswinkel-
Meßgeräte, Leitstungsfaktor- Meßgeräte und Synchronoskope (IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à action directe et leurs

accessoires - Partie 5: Prescriptions particulières pour les phasemètres, les indicateurs

de facteur de puissance et les synchronoscopes (IEC 60051-5:2017)
Ta slovenski standard je istoveten z: EN IEC 60051-5:2018
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
SIST EN 60051-5:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60051-5:2018
---------------------- Page: 2 ----------------------
SIST EN 60051-5:2018
EUROPEAN STANDARD EN IEC 60051-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2018
ICS 17.220.20 Supersedes EN 60051-5:1989
English Version
Direct acting indicating analogue electrical measuring
instruments and their accessories - Part 5: Special requirements
for phase meters, power factor meters and synchroscopes
(IEC 60051-5:2017)

Appareils mesureurs électriques indicateurs analogiques à Direkt wirkende anzeigende elektrische Meßgeräte und ihr

action directe et leurs accessoires - Partie 5: Exigences Zubehör - Meßgeräte mit Skalenanzeige - Teil 5: Spezielle

particulières pour les phasemètres, les appareils de mesure Anforderungen für Phasenverschiebungswinkel-Meßgeräte,

de facteur de puissance et les synchronoscopes Leitstungsfaktor- Meßgeräte und Synchronoskope

(IEC 60051-5:2017) (IEC 60051-5:2017)

This European Standard was approved by CENELEC on 2018-01-19. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN IEC 60051-5:2018 E
---------------------- Page: 3 ----------------------
SIST EN 60051-5:2018
EN IEC 60051-5:2018 (E)
European foreword

The text of document 85/581/CDV, future edition 5 of IEC 60051-5, prepared by IEC/TC 85

"Measuring equipment for electrical and electromagnetic quantities" was submitted to the IEC-

CENELEC parallel vote and approved by CENELEC as EN IEC 60051-5:2018.
The following dates are fixed:
(dop) 2018-10-19
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2021-01-19
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60051-5:1989.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directives.

For the relationship with EU Directives see informative Annex ZZ, which is an integral part of this

document.
Endorsement notice

The text of the International Standard IEC 60051-5:2017 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

1 2
IEC 60051-9 NOTE Harmonized as EN 60051-9 .
To be published. Stage at the time of publication: IEC CDV 60051-9:2018.
To be published. Stage at the time of publication: prEN 60051-9:2018.
---------------------- Page: 4 ----------------------
SIST EN 60051-5:2018
EN IEC 60051-5:2018 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:

www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60051-1 2016 Direct acting indicating analogue electrical EN 60051-1 2017
measuring instruments and their
accessories – Part 1: Definitions and
general requirements common to all parts
---------------------- Page: 5 ----------------------
SIST EN 60051-5:2018
---------------------- Page: 6 ----------------------
SIST EN 60051-5:2018
IEC 60051-5
Edition 5.0 2017-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Direct acting indicating analogue electrical measuring instruments and their
accessories –
Part 5: Special requirements for phase meters, power factor meters and
synchroscopes
Appareils mesureurs électriques indicateurs analogiques à action directe et
leurs accessoires –
Partie 5: Exigences particulières pour les phasemètres, les appareils de mesure
de facteur de puissance et les synchronoscopes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 17.220.20 ISBN 978-2-8322-5187-4

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60051-5:2018
– 2 – IEC 60051-5:2017 © IEC 2017
CONTENTS

FOREWORD ........................................................................................................................... 4

INTRODUCTION ..................................................................................................................... 6

1 Scope .............................................................................................................................. 7

2 Normative references ...................................................................................................... 7

3 Terms and definitions ...................................................................................................... 7

4 Description, classification and compliance ....................................................................... 7

4.1 Description ............................................................................................................. 7

4.2 Classification .......................................................................................................... 7

4.3 Compliance with the requirements of this standard ................................................. 7

5 Requirements .................................................................................................................. 8

5.1 Reference conditions .............................................................................................. 8

5.2 Limits of intrinsic uncertainty, fiducial value ............................................................ 8

5.2.1 Limits of intrinsic uncertainty ........................................................................... 8

5.2.2 Correspondence between intrinsic uncertainty and accuracy class .................. 8

5.2.3 Fiducial value .................................................................................................. 8

5.3 Nominal range of use and variations ....................................................................... 8

5.3.1 Nominal range of use ....................................................................................... 8

5.3.2 Limits of variations........................................................................................... 9

5.3.3 Conditions for the determination of variations ................................................ 10

5.4 Operating uncertainty, overall system uncertainty and variations .......................... 10

5.5 Electrical requirements ......................................................................................... 10

5.5.1 Electrical safety requirements ........................................................................ 10

5.5.2 Self-heating ................................................................................................... 10

5.5.3 Permissible overloads .................................................................................... 10

5.5.4 Limiting range of temperature ........................................................................ 11

5.5.5 Deviation from zero ....................................................................................... 11

5.5.6 Electromagnetic compatibility (EMC) ............................................................. 11

5.5.7 Special requirements for synchroscopes ........................................................ 12

5.6 Constructional requirements ................................................................................. 12

5.6.1 General constructional requirements ............................................................. 12

5.6.2 Damping ........................................................................................................ 12

5.6.3 Sealing to prevent access .............................................................................. 12

5.6.4 Scales ........................................................................................................... 12

5.6.5 Stopper.......................................................................................................... 12

5.6.6 Preferred values ............................................................................................ 12

5.6.7 Adjusters, mechanical and/or electrical .......................................................... 13

5.6.8 Effects of vibration and shock ........................................................................ 13

5.6.9 Degrees of protection provided by enclosure ................................................. 13

5.6.10 Terminals ...................................................................................................... 13

6 Information, markings and symbols ................................................................................ 13

6.1 Information ........................................................................................................... 13

6.2 Markings, symbols and their locations ................................................................... 13

6.3 Markings relating to the reference values and nominal ranges of use of

influence quantities ............................................................................................... 13

6.4 The symbols for marking instruments and accessories .......................................... 13

6.5 Markings and symbols for terminals ...................................................................... 13

---------------------- Page: 8 ----------------------
SIST EN 60051-5:2018
IEC 60051-5:2017 © IEC 2017 – 3 –

6.5.1 Requirements for markings ............................................................................ 13

6.5.2 Earthing (grounding) terminals ....................................................................... 13

6.5.3 Measuring circuit terminals ............................................................................ 14

6.5.4 Special markings for terminals ....................................................................... 14

6.6 Instructions for use ............................................................................................... 14

7 Package ........................................................................................................................ 14

8 Test rules ...................................................................................................................... 14

Annex A (normative) Nonconformity classification of tests ................................................... 15

Bibliography .......................................................................................................................... 16

Table 1 – Reference conditions and tolerances, additional to those given in Table 2 of

IEC 60051-1:2016, for testing purposes relating to the influence quantities ............................. 8

Table 2 – Limits of the nominal range of use and permissible variations in addition to

those given in Table 3 of IEC 60051-1:2016 ............................................................................ 9

Table 3 – Overloads of short duration ................................................................................... 11

Table A.1 – Nonconformity classification of tests .................................................................. 15

---------------------- Page: 9 ----------------------
SIST EN 60051-5:2018
– 4 – IEC 60051-5:2017 © IEC 2017
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
DIRECT ACTING INDICATING ANALOGUE ELECTRICAL
MEASURING INSTRUMENTS AND THEIR ACCESSORIES –
Part 5: Special requirements for phase meters,
power factor meters and synchroscopes
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60051-5 has been prepar
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.