ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS) - Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Mobile Earth Stations (MES) as
defined in annex B used within Satellite radio services, and ancillary equipment in respect of ElectroMagnetic
Compatibility (EMC).
Technical specifications related to the antenna port and emissions from the enclosure port of the equipment are not
included in the present document. Such technical specifications are found in the relevant product standards for the
effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
MESs and for the associated ancillary equipment.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The applicable
environment(s) referred to in ETSI EN 301 489-1 [1] where the MES may be used, should be declared by the
manufacturer.
For a multimode radio station, the present document only applies to the radio station when operated in the Mobile
Satellite Service mode.
NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive
2014/53/EU [i.1] is given in annex A.

Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 20. del: Posebni pogoji za mobilne zemeljske postaje (MES) v okviru mobilnih satelitskih storitev (MSS) - Harmonizirani standard, ki zajema bistvene zahteve člena 3.1(b) direktive 2014/53/EU

Ta dokument skupaj s standardom ETSI EN 301 489-1 [1] zajema oceno elektromagnetne združljivosti (EMC) mobilnih zemeljskih postaj (MES), kot so opredeljene v dodatku B za satelitske radijske storitve in pomožno opremo.
Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskim vhodom in sevanjem iz vhoda na ohišju opreme. Take tehnične specifikacije so navedene v ustreznih standardih za izdelek na področju učinkovite uporabe radijskega spektra.
Ta dokument določa veljavne preskusne pogoje, oceno zmogljivosti in kriterije zmogljivosti postaj MES in povezane pomožne opreme.
Če se ta dokument in standard ETSI EN 301 489-1 [1] razlikujeta (na primer glede posebnih pogojev, opredelitev, kratic), imajo prednost določbe tega dokumenta.
Okoljska razvrstitev ter zahteve glede sevanja in odpornosti iz tega dokumenta so navedene v standardu ETSI EN 301 489-1 [1], razen posebnih pogojev iz tega dokumenta. Veljavna okolja, ki so navedena v standardu ETSI EN 301 489-1 [1], v katerih se lahko uporablja oprema MES, naj bi navedel proizvajalec.
Pri večnačinovni radijski postaji se ta dokument nanaša samo na radijsko postajo, ko deluje v načinu mobilne satelitske storitve.
OPOMBA: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.1(b) direktive 2014/53/EU [i.1] je podano v dodatku A.

General Information

Status
Published
Public Enquiry End Date
17-Dec-2017
Publication Date
15-Apr-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Apr-2019
Due Date
20-Jun-2019
Completion Date
16-Apr-2019

Buy Standard

Standard
ETSI EN 301 489-20 V2.1.1 (2019-04) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS); Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
SIST EN 301 489-20 V2.1.1:2019
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 301 489-20 V2.1.0 (2017-10) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS) Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
20 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

ETSI EN 301 489-20 V2.1.1 (2019-04)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 20: Specific conditions for Mobile Earth Stations (MES)
used in the Mobile Satellite Services (MSS);
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-20 V2.1.1 (2019-04)
Reference
REN/ERM-EMC-366-20
Keywords
earth station, EMC, harmonised standard, MSS,
radio, regulation, satellite, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-20 V2.1.1 (2019-04)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 7

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 8

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................. 10

4.3 Exclusion bands ................................................................................................................................................ 10

4.3.0 General ........................................................................................................................................................ 10

4.3.1 Transmitter exclusion band ......................................................................................................................... 10

4.3.2 Receiver exclusion band ............................................................................................................................. 10

4.4 Narrow band responses of receivers ................................................................................................................. 10

5 Performance assessment ......................................................................................................................... 10

5.1 General ............................................................................................................................................................. 10

5.2 MES connected to host equipment ................................................................................................................... 11

5.2.0 General ........................................................................................................................................................ 11

5.2.1 Alternative A: combined equipment ........................................................................................................... 11

5.2.2 Alternative B: use of a test jig..................................................................................................................... 11

5.3 Ancillary equipment ......................................................................................................................................... 11

5.4 Equipment classification .................................................................................................................................. 11

6 Performance criteria ............................................................................................................................... 12

6.1 General ............................................................................................................................................................. 12

6.2 Performance criteria for Continuous Phenomena (CP) .................................................................................... 12

6.3 Performance criteria for Transient Phenomena (TP) ........................................................................................ 12

7 Applicability overview ........................................................................................................................... 12

7.1 Emission ........................................................................................................................................................... 12

7.1.1 General ........................................................................................................................................................ 12

7.1.2 Special conditions ....................................................................................................................................... 13

7.2 Immunity .......................................................................................................................................................... 13

7.2.1 General ........................................................................................................................................................ 13

7.2.2 Special conditions ....................................................................................................................................... 13

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 14

Annex B (normative): Definitions of MESs within the scope of the present document ................. 16

B.0 General ................................................................................................................................................... 16

B.1 MESs operating within 1,6 GHz/2,4 GHz band ................................................................................ ..... 16

B.2 MESs operating within the 1,5 GHz/1,6 GHz ........................................................................................ 16

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-20 V2.1.1 (2019-04)

B.3 MESs operating within 2,0 GHz band .................................................................................................... 16

B.4 MESs operating below 1 GHz ................................................................................................................ 17

B.5 MESs operating in the 11 GHz/12 GHz/14 GHz frequency bands ........................................................ 17

Annex C (informative): Bibliography ................................................................................................... 18

Annex D (informative): Change history ............................................................................................... 19

History .............................................................................................................................................................. 20

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-20 V2.1.1 (2019-04)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 20 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 15 January 2018
Date of latest announcement of this EN (doa): 31 July 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2020
Date of withdrawal of any conflicting National Standard (dow): 31 January 2021
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-20 V2.1.1 (2019-04)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Mobile Earth Stations (MES) as

defined in annex B used within Satellite radio services, and ancillary equipment in respect of ElectroMagnetic

Compatibility (EMC).

Technical specifications related to the antenna port and emissions from the enclosure port of the equipment are not

included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

MESs and for the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The applicable

environment(s) referred to in ETSI EN 301 489-1 [1] where the MES may be used, should be declared by the

manufacturer.

For a multimode radio station, the present document only applies to the radio station when operated in the Mobile

Satellite Service mode.

NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive

2014/53/EU [i.1] is given in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.2.0) (03-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".
[2] ITU-R Radio Regulations (2016).
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-20 V2.1.1 (2019-04)

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

carrier-on state (allocated a channel): state of an MES when it is transmitting a signal in a continuous or a

non-continuous mode

carrier-off state (idle mode): state of an MES when it is powered-on but not transmitting a signal, i.e. not in a

carrier-on state

host equipment: any equipment which has complete user functionality when not connected to the MES, and to which

connection is necessary for the MES to offer additional functionality

Installable Equipment (IE), Internally Mounted Equipment (IME) and Externally Mounted Equipment (EME):

equipment which is intended to be installed in a vehicle

NOTE: An IE may consist of one or several modules. The IE is composed of modules intended to be externally

mounted and declared by the manufacturer as Externally Mounted Equipment (EME). The remaining

module(s) are defined as Internally Mounted Equipment (IME).

multimode MES: equipment that accommodates radio stations of different radio systems

occupied bandwidth: See ITU-R Radio Regulations [2], part A, chapter 1, Terminology RR 147.

Portable Equipment (PE): equipment generally intended to be self-contained, free standing and portable

NOTE 1: A PE would normally consist of a single module, but may consist of several interconnected modules.

NOTE 2: More than one of the equipment classifications can apply to certain equipment, as described in clause 5.4,

dependent upon the manufacturer's declaration of normal intended use.

transmission disabled state: state of an MES when it is not authorized to transmit by the Network Control

Facilities (NCF)
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
CP performance criteria for Continuous Phenomena
EMC ElectroMagnetic Compatibility
EME Externally Mounted Equipment
EUT Equipment Under Test
F-MES Fixed MES
IE Installable Equipment
IME Internally Mounted Equipment
LBRDC Low Bit Rate Data Communication
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-20 V2.1.1 (2019-04)
LEO Low Earth Orbit
MES Mobile Earth Station
MSS Mobile Satellite Service
NCF Network Control Facilities
PCN Personal Communication Network
PE Portable Equipment
PEP Peak Envelope Power
P-MES Portable MES
QTMA Quality of Transmission Measurement Apparatus
RF Radio Frequency
S-PCN Satellite Personal Communications Network
STE Special Test Equipment
TP performance criteria for Transient Phenomena
V-MES Vehicle mounted MES
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as

appropriate. Further product related test conditions for MES are specified in the present document.

For MESs with ancillary equipment and/or various ports, the number of test configurations shall be determined. The

assessment shall include sufficient representative configurations of the MES to adequately exercise the equipment.

These configurations shall be recorded in the test report.

In the following clauses, the Equipment Under Test (EUT) is the MES with the selected configuration of ancillary

equipment.

The EUT operational frequencies used during the test, shall be recorded in the test report.

For testing and if physically separated from the MES, any voltage converter shall form part of the EUT.

Whenever the Equipment Under Test (EUT) is provided with an integral antenna, the EUT shall be tested with the

antenna fitted in a manner typical of normal intended use.

For MES for which connection to a host equipment is necessary to offer additional functionality, the test configuration

shall be as defined in clause 5.2.
4.2 Arrangements for test signals
4.2.1 Arrangements for test signals at the input of transmitters
The provisions of ETSI EN 301 48
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.RELOQLKElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS) - Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.40SatelitSatellite33.060.01Radijske komunikacije na splošnoRadiocommunications in generalICS:Ta slovenski standard je istoveten z:ETSI EN 301 489-20 V2.1.1 (2019-04)SIST EN 301 489-20 V2.1.1:2019en01-junij-2019SIST EN 301 489-20 V2.1.1:2019SLOVENSKI

STANDARD
SIST EN 301 489-20 V2.1.1:2019

ETSI EN 301 489-20 V2.1.1 (2019-04) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 20: Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS); Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU

HARMONISED EUROPEAN STANDARD SIST EN 301 489-20 V2.1.1:2019
ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)2

Reference REN/ERM-EMC-366-20 Keywords earth station, EMC, harmonised standard, MSS, radio, regulation, satellite, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI deliverable is the one made publicly available in PDF format at www.etsi.org/deliver. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTETM are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the oneM2M Partners. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)3 Contents Intellectual Property Rights ................................................................................................................................ 5 Foreword ............................................................................................................................................................. 5 Modal verbs terminology .................................................................................................................................... 5 1 Scope ........................................................................................................................................................ 6 2 References ................................................................................................................................................ 6 2.1 Normative references ......................................................................................................................................... 6 2.2 Informative references ........................................................................................................................................ 6 3 Definitions and abbreviations ................................................................................................................... 7 3.1 Definitions .......................................................................................................................................................... 7 3.2 Abbreviations ..................................................................................................................................................... 7 4 Test conditions ......................................................................................................................................... 8 4.1 General ............................................................................................................................................................... 8 4.2 Arrangements for test signals ............................................................................................................................. 8 4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8 4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 8 4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9 4.2.4 Arrangements for test signals at the output of receivers ............................................................................... 9 4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................. 10 4.3 Exclusion bands ................................................................................................................................................ 10 4.3.0 General ........................................................................................................................................................ 10 4.3.1 Transmitter exclusion band ......................................................................................................................... 10 4.3.2 Receiver exclusion band ............................................................................................................................. 10 4.4 Narrow band responses of receivers ................................................................................................................. 10 5 Performance assessment ......................................................................................................................... 10 5.1 General ............................................................................................................................................................. 10 5.2 MES connected to host equipment ................................................................................................................... 11 5.2.0 General ........................................................................................................................................................ 11 5.2.1 Alternative A: combined equipment ........................................................................................................... 11 5.2.2 Alternative B: use of a test jig..................................................................................................................... 11 5.3 Ancillary equipment ......................................................................................................................................... 11 5.4 Equipment classification .................................................................................................................................. 11 6 Performance criteria ............................................................................................................................... 12 6.1 General ............................................................................................................................................................. 12 6.2 Performance criteria for Continuous Phenomena (CP) .................................................................................... 12 6.3 Performance criteria for Transient Phenomena (TP) ........................................................................................ 12 7 Applicability overview ........................................................................................................................... 12 7.1 Emission ........................................................................................................................................................... 12 7.1.1 General ........................................................................................................................................................ 12 7.1.2 Special conditions ....................................................................................................................................... 13 7.2 Immunity .......................................................................................................................................................... 13 7.2.1 General ........................................................................................................................................................ 13 7.2.2 Special conditions ....................................................................................................................................... 13 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU ......................................................... 14 Annex B (normative): Definitions of MESs within the scope of the present document ................. 16 B.0 General ................................................................................................................................................... 16 B.1 MESs operating within 1,6 GHz/2,4 GHz band ..................................................................................... 16 B.2 MESs operating within the 1,5 GHz/1,6 GHz ........................................................................................ 16 SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)4 B.3 MESs operating within 2,0 GHz band .................................................................................................... 16 B.4 MESs operating below 1 GHz ................................................................................................................ 17 B.5 MESs operating in the 11 GHz/12 GHz/14 GHz frequency bands ........................................................ 17 Annex C (informative): Bibliography ................................................................................................... 18 Annex D (informative): Change history ............................................................................................... 19 History .............................................................................................................................................................. 20

SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)5 Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document is part 20 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates Date of adoption of this EN: 15 January 2018 Date of latest announcement of this EN (doa): 31 July 2019 Date of latest publication of new National Standard or endorsement of this EN (dop/e):

31 January 2020 Date of withdrawal of any conflicting National Standard (dow): 31 January 2021

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)6 1 Scope The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Mobile Earth Stations (MES) as defined in annex B used within Satellite radio services, and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of the equipment are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment and performance criteria for MESs and for the associated ancillary equipment. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The applicable environment(s) referred to in ETSI EN 301 489-1 [1] where the MES may be used, should be declared by the manufacturer. For a multimode radio station, the present document only applies to the radio station when operated in the Mobile Satellite Service mode. NOTE: The relationship between the present document and essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] is given in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ETSI EN 301 489-1 (V2.2.0) (03-2017): "ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential requirements of article 6 of Directive 2014/30/EU". [2] ITU-R Radio Regulations (2016). 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)7 The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following apply: carrier-on state (allocated a channel): state of an MES when it is transmitting a signal in a continuous or a non-continuous mode carrier-off state (idle mode): state of an MES when it is powered-on but not transmitting a signal, i.e. not in a carrier-on state host equipment: any equipment which has complete user functionality when not connected to the MES, and to which connection is necessary for the MES to offer additional functionality Installable Equipment (IE), Internally Mounted Equipment (IME) and Externally Mounted Equipment (EME): equipment which is intended to be installed in a vehicle NOTE: An IE may consist of one or several modules. The IE is composed of modules intended to be externally mounted and declared by the manufacturer as Externally Mounted Equipment (EME). The remaining module(s) are defined as Internally Mounted Equipment (IME). multimode MES: equipment that accommodates radio stations of different radio systems occupied bandwidth: See ITU-R Radio Regulations [2], part A, chapter 1, Terminology RR 147. Portable Equipment (PE): equipment generally intended to be self-contained, free standing and portable NOTE 1: A PE would normally consist of a single module, but may consist of several interconnected modules. NOTE 2: More than one of the equipment classifications can apply to certain equipment, as described in clause 5.4, dependent upon the manufacturer's declaration of normal intended use. transmission disabled state: state of an MES when it is not authorized to transmit by the Network Control Facilities (NCF) 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: CP performance criteria for Continuous Phenomena EMC ElectroMagnetic Compatibility EME Externally Mounted Equipment EUT Equipment Under Test F-MES Fixed MES IE Installable Equipment IME Internally Mounted Equipment LBRDC Low Bit Rate Data Communication SIST EN 301 489-20 V2.1.1:2019

ETSI ETSI EN 301 489-20 V2.1.1 (2019-04)8 LEO Low Earth Orbit MES Mobile Earth Station MSS Mobile Satellite Service NCF Network Control Facilities PCN Personal Communication Network PE Portable Equipment PEP Peak Envelope Power P-MES Portable MES QTMA Quality of Transmission Measurement Apparatus RF Radio Frequency S-PCN Satellite Personal Communications Network STE Special Test Equipment TP performance criteria for Transient Phenomena V-MES Vehicle mounted MES 4 Test conditions 4.1 General For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as appropriate. Further product related test conditions for MES are specified in the present document. For MESs with ancillary equipment and/or various ports, the number of test configurations shall be determined. The assessment shall include sufficient representative configurations of the MES to adequately exercise the equipment. These configurations shall be recorded in the test report. In the following clauses, the Equipment Under Test (EUT) is the MES with the selected configuration of ancillary equipment. The EUT operational frequencies used during the test, shall be recorded in the test report. For testing and if physically se

...

Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC) standard
for radio equipment and services;
Part 20: Specific conditions for Mobile Earth Stations (MES)
used in the Mobile Satellite Services (MSS)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
Reference
REN/ERM-EMC-366-20
Keywords
earth station, EMC, harmonised standard, MSS,
radio, regulation, satellite, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.

GSM® and the GSM logo are trademarks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definitions and abbreviations ................................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Arrangements for test signals ............................................................................................................................. 8

4.2.1 Arrangements for test signals at the input of transmitters ............................................................................. 8

4.2.2 Arrangements for test signals at the output of transmitters ........................................................................... 9

4.2.3 Arrangements for test signals at the input of receivers ................................................................................. 9

4.2.4 Arrangements for test signals at the output of receivers ............................................................................. 10

4.2.5 Arrangements for testing transmitter and receiver together (as a system) .................................................. 10

4.3 Exclusion bands ................................................................................................................................................ 10

4.3.0 General ........................................................................................................................................................ 10

4.3.1 Transmitter exclusion band ......................................................................................................................... 10

4.3.2 Receiver exclusion band ............................................................................................................................. 10

4.4 Narrow band responses of receivers ................................................................................................................. 10

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 MES connected to host equipment ................................................................................................................... 11

5.2.0 General ........................................................................................................................................................ 11

5.2.1 Alternative A: combined equipment ........................................................................................................... 11

5.2.2 Alternative B: use of a test jig..................................................................................................................... 11

5.3 Ancillary equipment ......................................................................................................................................... 11

5.4 Equipment classification .................................................................................................................................. 12

6 Performance criteria ............................................................................................................................... 12

6.1 General ............................................................................................................................................................. 12

6.2 Performance criteria for Continuous Phenomena (CP) .................................................................................... 12

6.3 Performance criteria for Transient Phenomena (TP) ........................................................................................ 12

7 Applicability overview ........................................................................................................................... 13

7.1 Emission ........................................................................................................................................................... 13

7.1.1 General ........................................................................................................................................................ 13

7.1.2 Special conditions ....................................................................................................................................... 13

7.2 Immunity .......................................................................................................................................................... 13

7.2.1 General ........................................................................................................................................................ 13

7.2.2 Special conditions ....................................................................................................................................... 13

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 14

Annex B (normative): Definitions of MESs within the scope of the present document ................. 16

B.0 General ................................................................................................................................................... 16

B.1 MESs operating within 1,6 GHz/2,4 GHz band ................................................................................ ..... 16

B.2 MESs operating within the 1,5 GHz/1,6 GHz ........................................................................................ 16

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)

B.3 MESs operating within 2,0 GHz band .................................................................................................... 16

B.4 MESs operating below 1 GHz ................................................................................................................ 17

B.5 MESs operating in the 11 GHz/12 GHz/14 GHz frequency bands ........................................................ 17

Annex C (informative): Bibliography ................................................................................................... 18

Annex D (informative): Change history ............................................................................................... 19

History .............................................................................................................................................................. 20

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 20 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Mobile Earth Stations (MES) as

defined in annex B used within Satellite radio services, and ancillary equipment in respect of ElectroMagnetic

Compatibility (EMC).

Technical specifications related to the antenna port and emissions from the enclosure port of the equipment are not

included in the present document. Such technical specifications are found in the relevant product standards for the

effective use of the radio spectrum.

The present document specifies the applicable test conditions, performance assessment and performance criteria for

MESs and for the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document. The applicable

environment(s) referred to in ETSI EN 301 489-1 [1] where the MES may be used, should be declared by the

manufacturer.

For a multimode radio station, the present document only applies to the radio station when operated in the Mobile

Satellite Service mode.

NOTE: The relationship between the present document and essential requirements of article 3.1b of Directive

2014/53/EU [i.1] is given in Annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.2.0) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".
[2] ITU-R Radio Regulations (2016).
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following

apply:

carrier-on state (allocated a channel): state of an MES when it is transmitting a signal in a continuous or a

non-continuous mode

carrier-off state (idle mode): state of an MES when it is powered-on but not transmitting a signal, i.e. not in a

carrier-on state

host equipment: any equipment which has complete user functionality when not connected to the MES, and to which

connection is necessary for the MES to offer additional functionality

Installable Equipment (IE), Internally Mounted Equipment (IME) and Externally Mounted Equipment (EME):

equipment which is intended to be installed in a vehicle

NOTE: An IE may consist of one or several modules. The IE is composed of modules intended to be externally

mounted and declared by the manufacturer as Externally Mounted Equipment (EME). The remaining

module(s) are defined as Internally Mounted Equipment (IME).

multimode MES: equipment that accommodates radio stations of different radio systems

occupied bandwidth: See ITU-R Radio Regulations [2], part A, chapter 1, Terminology RR 147.

Portable Equipment (PE): equipment generally intended to be self-contained, free standing and portable

NOTE 1: A PE would normally consist of a single module, but may consist of several interconnected modules.

NOTE 2: More than one of the equipment classifications can apply to certain equipment, as described in clause 5.4,

dependent upon the manufacturer's declaration of normal intended use.

transmission disabled state: state of an MES when it is not authorized to transmit by the Network Control

Facilities (NCF)
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-20 V2.1.0 (2017-10)
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
CP performance criteria for Continuous Phenomena
EMC ElectroMagnetic Compatibility
EME Externally Mounted Equipment
EUT Equipment Under Test
F-MES Fixed MES
IE Installable Equipment
IME Internally Mounted Equipment
LBRDC Low Bit Rate Data Communication
LEO Low Earth Orbit
MES Mobile Earth Station
MSS Mobile Satellite Service
NCF Network Control Facilities
PCN Personal Communication Network
PE Portable Equipment
PEP Peak Envelope Power
P-MES Portable MES
QTMA Quality of Transmission Measurement Apparatus
RF Radio Frequency
S-PCN Satellite Personal Communications Network
STE Special Test Equipment
TP performance criteria for Transient Phenomena
V-MES Vehicle mounted MES
4 Test conditions
4.1 General

For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as

appropriate. Further product related test conditions for MES are specified in the present document.

For MESs with ancillary equipment and/or various ports, the number of test configurations shall be determined. The

assessment shall include sufficient representative configurations of the MES to adequately exercise the equipment.

These configurations shall be recorded in the test report.

In the following clauses, the Equipment Under Test (EUT) is the MES with the selected configuration of ancillary

equipment.

The EUT operational frequencies used during the test, shall be recorded in the test report.

For testing and if physically separated from the MES, any voltage converter shall form part of the EUT.

Whenever the Equipment Under Test (EUT) is provided with an integral antenna, the EUT shall be tested with the

antenna fitted in a manner typical of normal intended use.

For MES for which connection to a host equipment is necessary to offer additional functionality, the test configuration

shall be as defined in clause 5.2.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.