iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST HD 452.1.S1:2002

(Main)

Analogue signals for process control systems -- Part 1: Direct current signals

Analogue signals for process control systems -- Part 1: Direct current signals

Applicable to analogue direct current signals used in industrial-process measurement and control systems to transmit information between elements of systems. Does not apply to signals used entirely within an element.

Analoge Signale für Regel- und Steueranlagen -- Teil 1: Analoge Gleichstromsignale

Signaux analogiques pour systèmes de commande de processus -- Partie 1: Signaux à courant continu

Applicable aux signaux analogiques à courant continu utilisés dans les systèmes de mesure et de commande des processus industriels pour transmettre les informations entre les éléments du système. Ne s'applique pas aux signaux utilisés exclusivement à l'intérieur d'un élément.

Analogue signals for process control systems - Part 1: Direct current signals

General Information

Status
Published
Publication Date
30-Jun-2002
ICS
25.040.40 - Industrial process measurement and control
Technical Committee
MKP - Industrial-process measurement and control
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2002
Due Date
01-Jul-2002
Completion Date
01-Jul-2002
Ref Project
HD 452.1 S1:1984 - Analogue signals for process control systems - Part 1: Direct current signals

Buy Standard

HD 452.1.S1:2002HD 452.1.S1:2002
PreviousNext
Standardization document
HD 452.1.S1:2002
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST HD 452.1.S1:2002
01-julij-2002
Analogue signals for process control systems - Part 1: Direct current signals
Analogue signals for process control systems -- Part 1: Direct current signals
Analoge Signale für Regel- und Steueranlagen -- Teil 1: Analoge Gleichstromsignale
Signaux analogiques pour systèmes de commande de processus -- Partie 1: Signaux à
courant continu
Ta slovenski standard je istoveten z: HD 452.1 S1:1984
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
SIST HD 452.1.S1:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 --------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 61987-1:2007(Main)
Industrial-process measurement and control - Data structures and elements in process equipment catalogues -- Part 1: Measuring equipment with analogue and digital output
EN 61987-1:2007

This part of IEC 61987 defines a generic structure in which product features of industrialprocess measurement and control equipment with analogue or digital output should be arranged, in order to facilitate the understanding of product descriptions when they are transferred from one party to another. It applies to the production of catalogues of process measuring equipment supplied by the manufacturer of the product and helps the user to formulate his requirements. This standard also serves as a reference document for all future standards which are concerned with process measuring equipment catalogues. In addition, it is intended as a guide for the production of further standards on process equipment documentation for similar systems, for example, for other measuring equipment and actuators.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-1:2007(Main)
Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
EN 60534-8-1:2005

This part of IEC 60534-8 defines equipment, methods, and procedures for obtaining laboratory measurements of sound pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Control valves discharging to atmosphere are excluded from this standard. Method A is a uniform method of measuring the radiated noise from the valve and associated test piping and allows a comparison of various measuring results which is beneficial for both user and manufacturer. The noise criteria are expressed by determining the sound pressure level of the valve under consideration. Method B is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. Since inaccuracies due to the pipe transmission are eliminated, this method is preferred for evaluation of the acoustical characteristic of valves. The noise characteristics to be determined are useful for the following reasons: a) to compare the performance of different valves; b) to plan measures for noise abatement; c) to determine acoustical characteristics of valves and valve assemblies; d) to enable proper sizing of sound absorbers; e) to determine possible adverse effects on ultra-sonic flow meter measurements.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-1:2007(Main)
Industrial-process control valves -- Part 1: Control valve terminology and general considerations
EN 60534-1:2005

This part of IEC 60534 applies to all types of industrial-process control valves (hereinafter referred to as control valves). This part establishes a partial basic terminology list and provides guidance on the use of all other parts of IEC 60534.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60770-3:2007(Main)
Transmitters for use in industrial-process control systems -- Part 3: Methods for performance evaluation of intelligent transmitters
EN 60770-3:2006

This part of IEC 60770 specifies the following methods. Methods for - reviewing the functionality and the degree of intelligence in intelligent transmitters; - testing the operational behaviour, as well as the static and dynamic performance of an intelligent transmitter. Methodologies for - determining the reliability and diagnostic features used to detect malfunctions; - determining the communication capabilities of the intelligent transmitters in a communication network. The methods and methodologies are applicable to intelligent transmitters, which convert one or more physical, chemical or electrical quantities into digital signals for use in a communication network or into analogue electrical signals (as specified in the IEC 60381 series). The methods and methodologies listed in this part of IEC 60770 are intended for use by: - manufacturers to determine the performance of their products and - users or independent testing laboratories to verify equipment performance specifications. Manufacturers of intelligent transmitters are urged to apply this part of IEC 60770 at an early stage of development. This standard is intended to provide guidance for designing evaluations of intelligent transmitters by providing: - a checklist for reviewing the hardware and software design in a structured way; - test methods for measuring and qualifying the performance, dependability and operability under various environmental and operational conditions; - methods for reporting the data obtained.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-4:2007(Main)
Industrial-process control valves -- Part 4: Inspection and routine testing
EN 60534-4:2006

This part of IEC 60534 specifies the requirements for the inspection and routine testing of control valves manufactured in conformity with the other parts of IEC 60534. This standard is applicable to valves with pressure ratings not exceeding Class 2500. The requirements for actuators apply only to pneumatic actuators. This standard does not apply to the types of control valves where radioactive service, fire safety testing, or other hazardous service conditions are encountered. If a standard for hazardous service conflicts with the requirements of this standard, the standard for hazardous service should take precedence.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61285:2007(Main)
Industrial-process control - Safety of analyser houses
EN 61285:2004

This International Standard describes the physical requirements for the safe operation of the process analyser measuring system installed in an AH in order to ensure its protection against fire, explosion and health hazards. This standard extends beyond IEC 60079-16 to include houses with Zone 2 interiors and to apply to toxic hazards. (Appropriate national guidelines on toxic hazards are to be followed.) This standard does not address facilities where dust is the hazard. Clause 4 addresses the location of the AH and connection within the process plant areas. Clause 5 addresses the design, construction and layout of the AH. It does not address parts of the analyser measuring system installed in other locations such as sample conditioning rooms (SCR) or switchgear rooms. Clause 6 addresses measures for reducing the danger of explosion for AHs while permitting maintenance of equipment with the power on and the case open. Using n-Pentane as an example, the LEL is 1,4 % or 14 000 × 10-6. The level immediately dangerous to life or health (which is the maximum level from which a worker could escape within 30 min without any escape-impairing symptoms or any irreversible health effects) is only 0,5 % or 5 000 × 10-6. Classification of a house interior as Zone 1 may imply that no technician can enter without protective equipment such as breathing gear. Placing an AH in a Zone 1 area would usually imply that no technician could approach the house without wearing protective equipment. Clause 7 addresses those measures for protecting personnel from materials in the atmosphere of AHs that are hazardous to health.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61804-2:2004(Main)
Function Blocks (FB) for process control -- Part 2: Specification of FB concept and Electronic Device Description Language (EDDL)
EN 61804-2:2004

is applicable to Function Blocks (FB) for process control and specifies the Electronic Device Description Language (EDDL), specifies FB by using the result of harmonization work as regards several elements. defines a subset of the requirements of EN 61804-1 (hereafter referred to as Part 1) only, while Part 1 describes requirements for a distributed system.

  • Standard
    361 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61784-1:2004(Main)
Digital data communications for measurement and control -- Part 1: Profile sets for continuous and discrete manufacturing relative to fieldbus use in industrial control systems
EN 61784-1:2004

Defines a set of protocol specific communication profiles based primarily on the EN 61158 series, to be used in the design of devices involved in communications in factory manufacturing and process control.

  • Standard
    269 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60873-1:2004(Main)
Electrical and pneumatic analogue chart recorders for use in industrial-process control systems -- Part 1: Methods for performance evaluation
EN 60873-1:2004

Applies to the programming of program-mable controller systems using the programming languages defined in EN 61131-3. It also provides guidelines for the implementation of these languages in programmable controller systems and their programming support environments (PSEs).

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61003-1:2004(Main)
Industrial-process control systems - Instruments with analogue inputs and two- or multi-state outputs -- Part 1: Methods of evaluating performance
EN 61003-1:2004

is applicable to pneumatic and electric industrial-process instruments using measured values that are continuous signals in accordance with EN 60382, or EN 60381-1. The other input value (i.e. the set point value) may be either a mechanical (position, force, etc.) or a standard signal.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day