SIST EN 60873-2:2004

Electrical and pneumatic analogue chart recorders for use in industrial process control systems -- Part 2: Guidance for inspection and routine testing

applies to electrical and pneumatic analogue chart recorders (for use in industrial-process control systems), operating from a standardized signal which may be used in process control. It is intended that continuous and dotted line traces, and multiple pen and multiple-channel instruments should be covered. Provides technical guidance for inspection and routine testing of electrical and pneumatic analogue chart recorders, for instance, as acceptance tests or after repair

Elektrische und pneumatische analoge Streifenschreiber zum Einsatz in Systemen industrieller Prozessleitteichnik -- Teil 2: Anleitung für die Abnahme und Betriebsprüfung

Enregistreurs de courbes électriques et pneumatiques pour une utilisation dans les systèmes de processus industriels -- Partie 2 : Guide pour les inspections et les essais individuels

applies to electrical and pneumatic analogue chart recorders (for use in industrial-process control systems), operating from a standardized signal which may be used in process control. It is intended that continuous and dotted line traces, and multiple pen and multiple-channel instruments should be covered. Provides technical guidance for inspection and routine testing of electrical and pneumatic analogue chart recorders, for instance, as acceptance tests or after repair

Electrical and pneumatic analogue chart recorders for use in industrial process control systems - Part 2: Guidance for inspection and routine testing

General Information

• Status: Published
• Publication Date: 31-May-2004
• ICS: 17.220.20 - Measurement of electrical and magnetic quantities
• ICS: 25.040.40 - Industrial process measurement and control
• Technical Committee: MKP - Industrial-process measurement and control
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jun-2004
• Due Date: 01-Jun-2004
• Completion Date: 01-Jun-2004
• Ref Project: EN 60873-2:2004 - Electrical and pneumatic analogue chart recorders for use in industrial process control systems - Part 2: Guidance for inspection and routine testing

Standards Content (Sample)

SLOVENSKI SIST EN 60873-2:2004

STANDARD
junij 2004
Electrical and pneumatic analogue chart recorders for use in industrial process
control systems - Part 2: Guidance for inspection and routine testing
ICS 17.220.20; 25.040.40 Referenčna številka
SIST EN 60873-2:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 60873-2
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2004

ICS 25.040.40


English version


Electrical and pneumatic analogue chart recorders
for use in industrial process control systems
Part 2: Guidance for inspection and routine testing
(IEC 60873-2:2004)


Enregistreurs de courbes électriques  Elektrische und pneumatische analoge
et pneumatiques pour une utilisation Streifenschreiber zum Einsatz in
dans les systèmes de processus Systemen industrieller Prozessleitteichnik
industriels Teil 2: Anleitung für die Abnahme
Partie 2 : Guide pour les inspections und Betriebsprüfung
et les essais individuels (IEC 60873-2:2004)
(CEI 60873-2:2004)


This European Standard was approved by CENELEC on 2004-03-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60873-2:2004 E

---------------------- Page: 2 ----------------------

EN 60873-2:2004 - 2 -
Foreword
The text of document 65B/513/FDIS, future edition 1 of IEC 60873-2, prepared by SC 65B, Devices, of
IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 60873-2 on 2004-03-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2004-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60873-2:2004 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60873-2:2004
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60410 1973 Sampling plans and procedures for - -
inspection by attributes

1) 2)
IEC 60873-1 - Electrical and pneumatic analogue chart EN 60873-1 2004
recorders for use in industrial-process
control systems
Part 1: Methods for performance
evaluation

IEC 61010-1 2001 Safety requirements for electrical EN 61010-1 2001
equipment for measurement, control, and + corr. June 2002
laboratory use
Part 1: General requirements

IEC 61298 Series Process measurement and control EN 61298 Series
devices - General methods and
procedures for evaluating performance




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC
STANDARD 60873-2
First edition
2004-01
Electrical and pneumatic analogue
chart recorders for use in industrial
process control systems –
Part 2:
Guidance for inspection
and routine testing
© IEC 2004 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale F
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue

---------------------- Page: 5 ----------------------

– 2 – 60873-2 © IEC:2004(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
ELECTRICAL AND PNEUMATIC ANALOGUE CHART RECORDERS
FOR USE IN INDUSTRIAL PROCESS CONTROL SYSTEMS –
Part 2: Guidance for inspection and routine testing
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
...