SIST EN 60317-55:2014

Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180

This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 180 with a dual coating. The underlying coating is based on polyurethane resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide resin. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is as follows:
– Grade 1: 0,020 mm up to and including 1,600 mm;
– Grade 2: 0,020 mm up to and including 1,600 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1:2013.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 55: Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan und darüber mit Polyamid, Klasse 180

Spécifications pour types particuliers de fils de bobinage -- Partie 55: Fil de section circulaire en cuivre émaillé avec polyuréthane brasable et avec surcouche polyamide, classe 180

La CEI 60317-55:2013 spécifie les exigences relatives au fil de bobinage brasable de section circulaire en cuivre émaillé de classe 180 avec un double revêtement. La sous-couche est à base de résine polyuréthane, qui peut être modifiée sous réserve de conserver l'identité chimique de la résine initiale et de répondre à toutes les exigences spécifiées pour le fil. La surcouche est à base de résine polyamide. NOTE - Une résine modifiée est une résine qui a subi une modification chimique, ou qui contient un ou plusieurs additifs pour améliorer certaines performances ou les caractéristiques d'utilisation. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est la suivante:  - Grade 1: 0,020 mm jusques et y compris 1,600 mm;  - Grade 2: 0,020 mm jusques et y compris 1,600 mm. Les diamètres nominaux des conducteurs sont spécifiés à l'Article 4 de la CEI 60317-0-1:2013. Cette deuxième édition annule et remplace la première édition parue en 2007. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:  - révision de l'Article 23, Détection des microfissures en immersion. Mots clés: exigences relatives au fil de bobinage brasable de section circulaire en cuivre émaillé, classe 180, double revêtement

Specifikacije za posebne vrste navijalnih žic - 55. del: S poliuretanom emajlirana okrogla bakrena žica, prevlečena s poliamidom, za spajkanje, razred 180 (IEC 60317-55:2013)

Ta del standarda IEC 60317 določa zahteve za spajkljive prevlečene okrogle bakrene navijalne žice razreda 180 z dvojno prevleko. Spodnja prevleka je osnovana na poliuretanski smoli, ki se lahko prilagodi, če ohrani kemijsko identiteto izvirne smole in zadosti vsem določenim zahtevam žice. Vrhnja prevleka je osnovana na poliamidni smoli. OPOMBA: Spremenjena smola je smola, ki je bila kemijsko spremenjena ali vsebuje enega ali več aditivov za izboljšanje določene lastnosti učinkovitosti ali uporabe. Razpon nazivnega premera prevodnika, ki ga zajema ta standard, je, kot sledi:
– razred 1: 0,020 mm do (vključno z) 1,600 mm;
– razred 2: 0,020 mm do (vključno z) 1,600 mm.
Nazivni premeri prevodnika so navedeni v točki 4 standarda IEC 60317-0-1:2013.

General Information

• Status: Published
• Publication Date: 09-Mar-2014
• ICS: 29.060.10 - Wires
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 27-Feb-2014
• Due Date: 04-May-2014
• Completion Date: 10-Mar-2014
• Ref Project: EN 60317-55:2014 - Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180

Relations

• Replaces: SIST EN 60317-55:2008 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180
• Effective Date: 20-Mar-2012
• Replaces: SIST EN 60317-55:2008 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60317-55:2008 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180
• Effective Date: 06-May-2014
• Amended By: SIST EN 60317-55:2014/A1:2019 - Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180 (IEC 60317-55:2013/A1:2019)
• Effective Date: 31-Jul-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60317-55:2014
01-april-2014
1DGRPHãþD
SIST EN 60317-55:2008
6SHFLILNDFLMH]DSRVHEQHYUVWHQDYLMDOQLKåLFGHO6SROLXUHWDQRPHPDMOLUDQD
RNURJODEDNUHQDåLFDSUHYOHþHQDVSROLDPLGRP]DVSDMNDQMHUD]UHG,(&

Specifications for particular types of winding wires -- Part 55: Solderable polyurethane
enamelled round copper wire overcoated with polyamide, Class 180
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 55:
Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan und darüber mit
Polyamid, Klasse 180
Spécifications pour types particuliers de fils de bobinage -- Partie 55: Fil de section
circulaire en cuivre émaillé avec polyuréthane brasable et avec surcouche polyamide,
classe 180
Ta slovenski standard je istoveten z: EN 60317-55:2014
ICS:
29.060.10 Žice Wires
SIST EN 60317-55:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60317-55:2014

---------------------- Page: 2 ----------------------

SIST EN 60317-55:2014

EUROPEAN STANDARD
EN 60317-55

NORME EUROPÉENNE
February 2014
EUROPÄISCHE NORM

ICS 29.060.10 Supersedes EN 60317-55:2008


English version


Specifications for particular types of winding wires -
Part 55: Solderable polyurethane enamelled round copper wire overcoated
with polyamide, Class 180
(IEC 60317-55:2013)


Spécifications pour types particuliers de Technische Lieferbedingungen für
fils de bobinage - bestimmte Typen von Wickeldrähten -
Partie 55: Fil brasable de section circulaire Teil 55: Runddrähte aus Kupfer,
en cuivre émaillé avec polyuréthane et verzinnbar, lackisoliert mit Polyurethan
avec surcouche polyamide, classe 180 und darüber mit Polyamid, Klasse 180
(CEI 60317-55:2013) (IEC 60317-55:2013)





This European Standard was approved by CENELEC on 2013-11-18. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-55:2014 E

---------------------- Page: 3 ----------------------

SIST EN 60317-55:2014
EN 60317-55:2014 - 2 -
Foreword
The text of document 55/1422/FDIS, future edition 2 of IEC 60317-55, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60317-55:2014.

The following dates are fixed:
(dop) 2014-08-18
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2016-11-18
standards conflicting with the
document have to be withdrawn

This document supersedes EN 60317-55:2008.

EN 60317-55:2014 includes the following significant technical changes with respect to
EN 60317-55:2008:
– revision to Clause 23, Pin hole test.

This standard is to be read in conjunction with EN 60317-0-1:2014.

The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to
reserve space for possible future wire requirements prior to those for wire packaging.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 60317-55:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified).
IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified).
IEC 60851 Series NOTE Harmonized as EN 60851 Series (not modified).

---------------------- Page: 4 ----------------------

SIST EN 60317-55:2014
- 3 - EN 60317-55:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60317-0-1 2013 Specifications for particular types EN 60317-0-1 2014
of winding wires -
Part 0-1: General requirements - Enamelled
round copper wire

---------------------- Page: 5 ----------------------

SIST EN 60317-55:2014

---------------------- Page: 6 ----------------------

SIST EN 60317-55:2014



IEC 60317-55

®


Edition 2.0 2013-10




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Specifications for particular types of winding wires –

Part 55: Solderable polyurethane enamelled round copper wire overcoated with

polyamide, class 180




Spécifications pour types particuliers de fils de bobinage –

Partie 55: Fil brasable de section circulaire en cuivre émaillé avec polyuréthane


et avec surcouche polyamide, classe 180













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX K


ICS 29.060.10 ISBN 978-2-8322-1136-6



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60317-55:2014
– 2 – 60317-55 © IEC:2013
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 6
3.2.1 Methods of test . 6
3.2.2 Winding wire . 6
3.3 Appearance . 7
4 Dimensions . 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion (nominal conductor diameters from 0,250 mm up to and
including 1,600 mm) . 7
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 9
17.1 Nominal conductor diameters up to and including 0,100 mm. 9
17.2 Nominal conductor diameters over 0,100 mm . 9
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography .
...