kSIST FprEN IEC 62275:2022
(Main)Cable management systems - Cable ties for electrical installations
Cable management systems - Cable ties for electrical installations
IEC 62275:2022 specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices as a means used for managing or securing the wiring systems in electrical installations. Cable ties and associated fixing devices can also be suitable for other applications, such as support of wiring systems, and where so used, additional requirements can apply. This fourth edition cancels and replaces the third edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- scope clarification,
- new definitions,
- deletion of the exception for the stabilization of the moisture content,
- possibility to carry out tensile strength tests with dead weights,
- differentiation of rubber and acrylic adhesive fixings,
- clarification for mechanical testing of integral devices,
- clarifications on Table 6,
- clarifications in 9.1,
- the minimum installation temperature test for cable ties is carried out only when the declared minimum temperature is lower than 0 °C,
- a requirement that metallic cable ties be classified according to 6.2.3,
- definition of colours to be tested for contribution to fire,
- addition of a "some countries" note in Clause 10,
- clarification of the mounting of fixing devices in the resistance to ultraviolet light test,
- clarification on the testing of integral devices in the resistance to ultraviolet light test.
Kabelführungssysteme - Kabelbinder für elektrische Installationen
Systèmes de câblage - Colliers pour installations électriques
L'IEC 62275:2022 spécifie les exigences pour les colliers métalliques, non métalliques et composites, ainsi que pour leurs accessoires de fixation associés, comme un moyen utilisé pour l’aménagement et la fixation des systèmes de câblage dans les installations électriques. Les colliers et leurs accessoires de fixation associés peuvent également être utilisés pour d’autres applications, comme le soutien des systèmes de câblage et, dans ce cas, des exigences supplémentaires peuvent s’appliquer. Cette quatrième édition annule et remplace la troisième édition parue en 2018. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
- une clarification du domaine d’application;
- de nouvelles définitions;
- la suppression de l’exception relative au conditionnement pour atteindre la reprise d’humidité;
- la possibilité d’effectuer des essais de tenue à la traction avec des poids morts;
- la différenciation des fixations adhésives en caoutchouc et en acrylique;
- une clarification pour les essais mécaniques des accessoires intégrés;
- des clarifications du Tableau 6;
- des clarifications de 9.1;
- l’essai des colliers à la température minimale d’installation est effectué uniquement lorsque la température minimale déclarée est inférieure à 0 °C;
- une exigence selon laquelle les colliers métalliques sont classés conformément à 6.2.3;
- la définition des couleurs à soumettre à essai en matière de contribution au feu;
- l’ajout d’une note "Dans certains pays" à l’Article 10;
- la clarification du montage des accessoires de fixation dans l’essai de tenue au rayonnement ultraviolet;
- la clarification de l’essai des accessoires intégrés dans l’essai de tenue au rayonnement ultraviolet.
Sistemi za urejanje pokabljenja - Kabelske vezice za električne inštalacije
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 62275:2022
01-april-2022
Sistemi za urejanje pokabljenja - Kabelske vezice za električne inštalacije
Cable management systems - Cable ties for electrical installations
Kabelführungssysteme - Kabelbinder für elektrische Installationen
Systèmes de câblage - Colliers pour installations électriques
Ta slovenski standard je istoveten z: prEN IEC 62275:2022
ICS:
29.120.99 Druga električna dodatna Other electrical accessories
oprema
oSIST prEN IEC 62275:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN IEC 62275:2022
---------------------- Page: 2 ----------------------
oSIST prEN IEC 62275:2022
23A/994/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62275 ED4
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2022-01-28 2022-04-22
SUPERSEDES DOCUMENTS:
23A/963/CD, 23A/978A/CC
IEC SC 23A : CABLE MANAGEMENT SYSTEMS
SECRETARIAT: SECRETARY:
United Kingdom Mr Rajeev Vagdia
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
TITLE:
Cable management systems - Cable ties for electrical installations
PROPOSED STABILITY DATE: 2026
NOTE FROM TC/SC OFFICERS:
Copyright © 2021 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing
National Committee positions. You may not copy or "mirror" the file or printed version of the document, or any
part of it, for any other purpose without permission in writing from IEC.
---------------------- Page: 3 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 2 23A/994/CDV
1 CONTENTS
2 CONTENTS . 2
3 FOREWORD . 4
4 1 Scope . 6
5 2 Normative references . 6
6 3 Terms and definitions . 6
7 4 General requirements . 8
8 5 General notes on tests . 8
9 6 Classification . 13
10 6.1 According to material . 13
11 6.1.1 Metallic component . 13
12 6.1.2 Non-metallic component . 13
13 6.1.3 Composite component . 13
14 6.2 According to loop tensile strength for cable ties and mechanical strength for
15 fixing devices . 13
16 6.2.1 Loop tensile strength for cable ties . 13
17 6.2.2 Type 1 – Retains at least 50 % of declared loop tensile strength for
18 cable ties and mechanical strength for fixing devices after test
19 conditions . 13
20 6.2.3 Type 2 – Retains 100 % declared loop tensile strength for cable ties
21 and mechanical strength for fixing devices after test conditions . 13
22 6.2.4 According to loop tensile strength and mechanical strength of integral
23 assemblies . 13
24 6.3 According to temperature . 14
25 6.3.1 According to maximum operating temperature for application given in
26 Table 4 . 14
27 6.3.2 According to minimum operating temperature for application given in
28 Table 5 . 14
29 6.3.3 According to minimum temperature during installation as declared by
30 the manufacturer . 14
31 6.4 According to contribution to fire for non-metallic and composite cable ties
32 and integral assemblies only . 14
33 6.4.1 Flame propagating . 14
34 6.4.2 Non-flame propagating . 14
35 6.5 According to environmental influences . 15
36 6.5.1 According to resistance to ultraviolet light for non-metallic and
37 composite components . 15
38 6.5.2 According to resistance to corrosion for metallic and composite
39 components . 15
40 7 Marking and documentation . 15
41 8 Construction . 17
42 9 Mechanical properties. 18
43 9.1 Requirements . 18
44 9.2 Installation test . 18
45 9.3 Minimum installation temperature test for cable ties . 18
46 9.4 Minimum operating temperature test for cable ties . 19
47 9.5 Loop tensile strength test for cable ties classified according to 6.2.2 . 21
48 9.5.1 As-received condition . 21
49 9.5.2 After heat ageing . 21
---------------------- Page: 4 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 3 23A/994/CDV
50 9.5.3 After temperature cycling . 22
51 9.6 Loop tensile strength test for cable ties classified according to 6.2.3 . 22
52 9.6.1 As-received condition . 22
53 9.6.2 After-heat ageing . 22
54 9.6.3 After temperature cycling . 23
55 9.6.4 After vibration test for metallic cable ties . 23
56 9.7 Mechanical strength test for fixing devices and integral assemblies . 25
57 9.7.1 As-received condition . 25
58 9.7.2 After-heat ageing . 30
59 9.7.3 After temperature cycling . 31
60 10 Contribution to fire . 32
61 11 Environmental influences . 34
62 11.1 Resistance to ultraviolet light . 34
63 11.2 Resistance to corrosion . 37
64 12 Electromagnetic compatibility . 37
65 Annex A (normative) Compliance checks to be carried out for cable ties and fixing
66 devices currently complying with IEC 62275:2018 in order to comply with this
67 edition 4 . 38
68 Bibliography . 40
69
70 Figure 1 – Reference thickness for cable ties . 9
71 Figure 2 – Typical arrangements for cable tie orientation on split mandrel for tensile
72 test 12
73 Figure 3 – Test piston for durability test for marking . 16
74 Figure 4 – Test apparatus for cable tie impact test . 21
75 Figure 5 – Typical arrangement for the vibration test . 24
76 Figure 6 – Typical arrangement of test assembly for fixing devices and for integral
77 fixing devices . 30
78 Figure 7 – Arrangement for the needle flame test . 34
79 Figure 8 – Recommended sample repositioning for ultraviolet light and water exposure . 36
80
81 Table 1 – Stabilization time for samples . 9
82 Table 2 – Test mandrel diameter . 10
83 Table 3 – Loop tensile strength . 13
84 Table 4 – Maximum operating temperature for application . 14
85 Table 5 – Minimum operating temperature for application . 14
86 Table 6 – Literature information . 17
87 Table 7 – Energy values of hammer . 21
88 Table A.1 – Required compliance checks . 38
89
90
---------------------- Page: 5 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 4 23A/994/CDV
91 INTERNATIONAL ELECTROTECHNICAL COMMISSION
92 ____________
93
94 CABLE MANAGEMENT SYSTEMS –
95 CABLE TIES FOR ELECTRICAL INSTALLATIONS
96
97 FOREWORD
98 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
99 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
100 international co-operation on all questions concerning standardization in the electrical and electronic fields. To
101 this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
102 Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
103 Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
104 in the subject dealt with may participate in this preparatory work. International, governmental and non-
105 governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
106 with the International Organization for Standardization (ISO) in accordance with conditions determined by
107 agreement between the two organizations.
108 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
109 consensus of opinion on the relevant subjects since each technical committee has representation from all
110 interested IEC National Committees.
111 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
112 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
113 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
114 misinterpretation by any end user.
115 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
116 transparently to the maximum extent possible in their national and regional publications. Any divergence
117 between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
118 the latter.
119 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
120 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
121 services carried out by independent certification bodies.
122 6) All users should ensure that they have the latest edition of this publication.
123 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
124 members of its technical committees and IEC National Committees for any personal injury, property damage or
125 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
126 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
127 Publications.
128 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
129 indispensable for the correct application of this publication.
130 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
131 patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
132 International Standard IEC 62275 has been prepared by subcommittee 23A: Cable
133 management systems, of IEC technical committee 23: Electrical accessories.
134 This fourth edition cancels and replaces the third edition published in 2018. This edition
135 constitutes a technical revision.
136 This edition includes the following significant technical changes with respect to the previous
137 edition:
138 a) scope clarification,
139 b) new definitions,
140 c) deletion of the exception for the stabilization of the moisture content
141 d) possibility to carry out tensile strength tests with dead weights,
142 e) differentiation of rubber and acrylic adhesive fixings,
143 f) clarification for mechanical testing of integral devices
---------------------- Page: 6 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 5 23A/994/CDV
144 g) clarifications on Table 6,
145 h) clarifications in subclause 9.1
146 i) the minimum installation temperature test for cable ties is carried out only when the
147 declared minimum temperature is lower than 0ºC,
148 j) metallic cable ties shall be classified according to 6.2.3,
149 k) definition of colours to be tested for contribution to fire,
150 l) addition of a “some countries” note in clause 10
151 m) clarification of the mounting of fixing devices in the resistance to ultraviolet light test
152 n) clarification on the testing of integral devices in the resistance to ultraviolet light test
153
154 The text of this standard is based on the following documents:
CD Compilation of Comments
23A/963/CD 23A/978A/CC
155
156 Full information on the voting for the approval of this standard can be found in the report on
157 voting indicated in the above table.
158 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
159 The following differing practices of a less permanent nature exist in the countries indicated
160 below.
161 – 6.2.2: additional type classifications are applicable when pre-qualified moulding materials
162 are used (Canada, USA).
163 – 6.2.3: additional type classifications are applicable when pre-qualified moulding materials
164 are used (Canada, USA).
165 – 7.3: some marking information is required to be placed on the packaging (Canada, Russia,
166 USA).
167 In this publication, the following print types are used:
168 – Requirements proper: in roman type.
169 – Test specifications: in italic type.
170 – Notes: in smaller roman type.
171 The committee has decided that the contents of this publication will remain unchanged until
172 the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data
173 related to the specific publication. At this date, the publication will be
174 reconfirmed,
175 withdrawn,
176 replaced by a revised edition, or
177 amended.
178
179
---------------------- Page: 7 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 6 23A/994/CDV
180 CABLE MANAGEMENT SYSTEMS –
181 CABLE TIES FOR ELECTRICAL INSTALLATIONS
182
183
184
185 1 Scope
186 This document specifies requirements for metallic, non-metallic and composite cable ties and
187 their associated fixing devices as a means used for managing or securing the wiring systems
188 in electrical installations. Cable ties and associated fixing devices can also be suitable for
189 other applications, such as support of wiring systems, and where so used, additional
190 requirements can apply.
191 This document does not contain requirements that evaluate any electrical insulation
192 properties of the cable tie or mechanical protection of the cables provided by the cable tie.
193 This document contains requirements for the mechanical interface of an adhesive fixing
194 device to a solid surface. It does not consider the mechanical behaviour of the solid surface in
195 itself.
196 This document does not consider the mechanical interface, for example the mounting screw,
197 of a fixing device other than adhesive to a solid surface.
198 2 Normative references
199 The following documents are referred to in the text in such a way that some or all of their
200 content constitutes requirements of this document. For dated references, only the edition
201 cited applies. For undated references, the latest edition of the referenced document (including
202 any amendments) applies.
203 IEC 60068-2-6:2007, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
204 IEC 60695-11-5:2016, Fire hazard testing – Part 11-5: Test flames – Needle-flame test
205 method – Apparatus, confirmatory test arrangement and guidance
206 IEC 60216-4-1:2006, Electrical insulating materials – Thermal endurance properties – Part 4-
207 1: Ageing ovens – Single-chamber ovens
208 ISO 4892-2:2013 + Amd.1:2021, Plastics – Methods of exposure to laboratory light sources –
209 Part 2: Xenon-arc lamps
210 ISO 9227:2017, Corrosion tests in artificial atmospheres – Salt spray tests
211 3 Terms and definitions
212 For the purposes of this document, the following terms and definitions apply.
213 ISO and IEC maintain terminological databases for use in standardization at the following
214 addresses:
215 IEC Electropedia: available at http://www.electropedia.org/
216 ISO Online browsing platform: available at http://www.iso.org/obp
---------------------- Page: 8 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 7 23A/994/CDV
217 3.1
218 cable tie
219 band or length of material, employing a locking device, used for bundling or tying groups of
220 cables together, securing and/or supporting the cables
221 Note 1 to entry: Type 1 and Type 2 cable ties are classified in 6.2.2 and 6.2.3.
222 Note 2 to entry: In some countries, such as Canada and the United States, additional Type classifications are
223 applicable when prequalified moulding materials are used. See UL 62275/CSA C22.2 No. 62275.
224 3.2
225 fixing device
226 component (such as a block or bracket) specifically designed to secure the cable tie to a
227 mounting surface
228 3.3
229 metallic component
230 component that consists of metal only
231 Note 1 to entry: A metallic cable tie having a thin non-metallic or organic coating, where the coating does not
232 contribute to the determination of the loop tensile strength, is considered a metallic component
233 Note 2 to entry: In case of doubt, "as-received condition" tests with and without coating can be carried out.
234 3.4
235 non-metallic component
236 component that consists of non-metallic material only
237 3.5
238 composite component
239 component comprising both metallic and non-metallic materials where both metallic and non-
240 metallic materials contribute to the determination of the loop tensile strength
241 3.6
242 environmental influence
243 effect of corrosive substances or solar radiation, etc.
244 3.7
245 loop tensile strength
246 reference mechanical characteristic of a cable tie with its locking mechanism engaged
247 3.8
248 locking device
249 feature of a cable tie for fixing it in a closed position
250 3.9
251 low hygroscopic polymer
252 polymer having the characteristic of not enabling attraction or holding water greater than
253 1,0 % by weight of the material from the surrounding environment at 23 °C and 50 % relative
254 humidity
255 Note 1 to entry: Examples of low hygroscopic polymers include polypropylene, acetal, ethylene
256 tetrafluoroethylene, ethylene chlorotrifluoroethylene, nylon 12, polyetheretherketone.
257 3.10
258 equilibrium moisture content
259 state at which a polymer neither absorbs or releases moisture when exposed to a surrounding
260 environment of 23 °C and 50 % relative humidity
---------------------- Page: 9 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 8 23A/994/CDV
261 3.11
262 integral device
263 a single component, as produced, incorporating a cable tie and a fixing device that are not
264 separatable.
265 3.12
266 adhesive fixing device
267 fixing device provided with an adhesive tape specifically designed to secure the cable tie to a
268 mounting surface
269 3.13
270 type test
271 conformity test made on one or more items representative of the production”
272 [SOURCE: ISO/IEC Guide 2 (14.5 MOD)]
273 3.14
274 bundle
275 collection of wires or cables gathered or tied together
276 4 General requirements
277 A cable tie and a fixing device shall withstand the stresses likely to occur during recom-
278 mended installation practice and perform under the conditions of classifications in Clause 6 as
279 declared by the manufacturer.
280 Compliance is checked by carrying out all the appropriate specified tests.
281 NOTE Annex A details the compliance checks to be carried out for cable ties and fixing devices currently
282 complying with IEC 62275:2013 in order to comply with this edition 4.
283 5 General notes on tests
284 5.1 Tests according to this document are type tests. Unless otherwise specified, tests are
285 carried out with the cable ties and their associated fixing devices, where available, installed
286 as in normal use according to the manufacturer's instructions.
287 Unless otherwise specified, requirements and tests for fixing devices also apply to adhesive
288 fixing devices.
289 NOTE For guidance in determining product types and sample sets, a family of cable ties or fixing devices having
290 material, construction characteristics, and classifications according to Clause 6, in common, are considered of the
291 same product type. Examples for consideration are identical generic material description, material colours, or
292 variable lengths of a cable tie of otherwise similar construction. The sample sets selected for testing from each
293 product type is representative of the extremes of the range (example: shortest and longest), and the minimum
294 performance level obtained for either extreme is determined to be representative of the entire range. Consideration
295 is given to minor construction variations that can be determined by inspection to have no effect on performance,
296 when determining product types.
297 5.2 Unless otherwise specified, tests on non-metallic and composite components shall
298 commence when the samples have been removed from their packaging and then stabilized at
299 a temperature of (23 5) °C and at a relative humidity of (50 5) %, for a period as indicated
300 in Table 1.
301 NOTE This stabilization intends to achieve equilibrium of moisture content for all samples before and after further
302 conditioning and testing.
---------------------- Page: 10 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 9 23A/994/CDV
303 Table 1 – Stabilization time for samples
Reference thickness (RT) of device Stabilization time
mm days
RT 1,2 7 1
0
1,2 RT 1,4 21
7
0
1,4 RT 35
7
All thicknesses of materials known to
2 1/3
have low hygroscopic characteristics
304 The reference thickness of a cable tie is measured at the midpoint of the strap. The reference
305 thickness of a fixing device shall be the smallest cross-section in the area that interfaces with
306 the cable tie or as declared by the manufacturer. See Figure 1.
A
Side view
Top view
A
IEC
307
308 Key
309 A reference thickness of cable tie
310 Figure 1 – Reference thickness for cable ties
311 5.3 Unless otherwise specified, the tests shall be carried out at an ambient temperature of
312 (23 5) °C and with a relative humidity of between 40 % and 60 %.
313 5.4 Unless otherwise specified, three new samples are submitted to the tests and the
314 requirements are satisfied if all the tests are met. If only one of the samples does not satisfy a
315 test owing to an assembly or manufacturing fault, that test and any preceding one which may
316 have influenced the results of the test shall be repeated. The tests that follow shall be carried
317 out in the required sequence on another full set of samples, all of which shall comply with the
318 requirements.
319 NOTE The applicant, when submitting the first set of samples, can also submit an additional set of samples which
320 may be necessary if one sample fails. The test station will then without further request test the additional set of
321 samples and will reject only if a further failure occurs. If the additional set of samples is not submitted at the same
322 time, a failure of one sample will entail a rejection.
323 5.5 When toxic or hazardous processes are used, due regard shall be taken of the safety of
324 persons within the test area.
---------------------- Page: 11 ----------------------
oSIST prEN IEC 62275:2022
IEC CDV 62275 © IEC 2021 10 23A/994/CDV
325 5.6 Unless otherwise specified, the cross-head speed of a tensile machine used during the
326 tests shall be (25 2,5) mm/min. Dead weights can be used for conducting loop tensile
327 strength tests for cable ties and integral devices classified according to 6.2.3, provided that
328 no sudden application of force occurs.
329 5.7 Where required for heat ageing, a full draft circulating-air oven as specified in
330 IEC 60216-4-1:2006 shall be used. A portion of the air shall be allowed to re-circulate and a
331 substantial amount of air shall be admitted continuously to maintain the normal air content
332 surrounding the samples. The oven shall be adjusted to achieve more than five complete
333 fresh-air changes per hour.
334 5.8 An integral device shall be tested as a complete sample. The integral device shall be
335 subjected to the conditionings for the cable tie prior to conducting the mec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.