SIST EN 13583:2012
(Main)Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance
Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance
This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail.
This European Standard may also be applied for waterproofing.
Abdichtungsbahnen - Bitumen-, Kunststoff- und Elastomerbahnen für Dachabdichtungen - Bestimmung des Widerstandes gegen Hagelschlag
Diese Europäische Norm legt das Prüfverfahren zur Bestimmung des Widerstandes von Dachabdichtungs-bahnen gegen Hagelschlag durch eine Perforationsprüfung mittels simulierten Hagelschlags fest.
Die Europäische Norm darf auch für Bauwerksabdichtungen angewendet werden.
Feuilles souples d'étanchéité - Feuilles bitumineuses, plastiques et élastomériques d'étanchéité de toiture - Détermination de la résistance à l'impact de la grêle
La présente Norme européenne décrit une méthode pour la détermination de la résistance à l'impact simulé de la grêle sur les feuilles destinées à l'étanchéité de toitures.
Elle peut également être utilisée pour des complexes d'étanchéité.
Hidroizolacijski trakovi - Bitumenski, polimerni in elastomerni trakovi za tesnjenje streh - Ugotavljanje odpornosti proti toči
Ta evropski standard določa ugotavljanje odpornosti elastičnih trakov za strehe proti toči na podlagi prebojnega preskusa, pri katerem se simulira toča. Ta evropski standard se lahko uporablja tudi za tesnjenje.
General Information
Relations
Overview
EN 13583:2012 (CEN) defines a standardized laboratory method to determine the hail resistance of flexible sheets for roof waterproofing (bitumen, plastic and rubber). The standard specifies a simulated-hail puncture test using a polyamide ball to assess whether a sheet is perforated by impact and reports the damaging velocity (vd) that produces perforation. Although focused on roof membranes, the method may also be applied to other waterproofing sheets.
Key topics and technical requirements
- Test principle: A polyamide ball is propelled by a pneumatic drive to strike the specimen; impact velocity is measured by photo-cells and varied to identify the damaging velocity (vd).
- Test projectile: Polyamide (PA 6.6) ball, mass (38.5 ± 0.5) g, diameter (40.0 ± 0.5) mm; smooth, defect-free surface.
- Supports: Two support conditions are defined:
- Hard support: steel plate with P120 silicon-carbide sandpaper (laid crosswise to sheet machine direction); steel plate temperature (10 ± 2) °C.
- Soft support: steel plate with an expanded polystyrene (EPS) panel (20 mm thick) with compressive stress CS(10) between 100 kPa and 110 kPa.
- Test area and conditioning: Ball impacts centered within a (200 ± 2) mm diameter opening; specimens conditioned 24 h at (23 ± 2) °C, 50 ± 10 % RH. Test area cooled to (0 ± 2) °C for (180 ± 30) s before impact.
- Result expression: Hail resistance is given as vd rounded to 1 m/s - the velocity that causes perforation in at most one out of five shots on hard and/or soft support.
- Precision & calibration: Speed measurement calibrated over 10–40 m/s; method precision approx. 10 %. Visual and vacuum/soap-bubble checks are specified to confirm perforation.
- Test report requirements: Product ID, thickness/mass (EN 1849-1/2), sampling, sandpaper type, EPS CS(10), procedure details, results and test date.
Applications and users
EN 13583:2012 is used for:
- Product development and quality control by membrane manufacturers to benchmark hail resistance.
- Independent testing labs for certification and performance reporting.
- Architects, specifiers and roof system designers to select membranes suitable for hail-prone regions.
- Contractors and asset owners for risk assessment, warranty validation and procurement.
- Regulators and standards bodies integrating performance criteria into building specifications.
Keywords: EN 13583:2012, hail resistance, flexible sheets for waterproofing, roof waterproofing, hail impact test, damaging velocity, puncture resistance.
Related standards
- EN 1849-1 / EN 1849-2 (thickness and mass)
- EN 13416 (sampling)
- EN 13956 (definitions for plastic/rubber sheets)
- EN 826 (EPS compression behaviour)
- ISO 6344-1 (abrasive grain size)
- prEN 10025-2 (steel specification)
Frequently Asked Questions
SIST EN 13583:2012 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance". This standard covers: This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail. This European Standard may also be applied for waterproofing.
This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail. This European Standard may also be applied for waterproofing.
SIST EN 13583:2012 is classified under the following ICS (International Classification for Standards) categories: 91.060.20 - Roofs; 91.100.50 - Binders. Sealing materials. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 13583:2012 has the following relationships with other standards: It is inter standard links to SIST EN 13583:2001. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 13583:2012 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC; Standardization Mandates: M/102. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 13583:2012 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Abdichtungsbahnen - Bitumen-, Kunststoff- und Elastomerbahnen für Dachabdichtungen - Bestimmung des Widerstandes gegen HagelschlagFeuilles souples d'étanchéité - Feuilles bitumineuses, plastiques et élastomériques d'étanchéité de toiture - Détermination de la résistance à l'impact de la grêleFlexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance91.100.50Veziva. Tesnilni materialiBinders. Sealing materials91.060.20StreheRoofsICS:Ta slovenski standard je istoveten z:EN 13583:2012SIST EN 13583:2012en,fr,de01-september-2012SIST EN 13583:2012SLOVENSKI
STANDARDSIST EN 13583:20011DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13583
July 2012 ICS 91.100.50 Supersedes EN 13583:2001English Version
Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of hail resistance Feuilles souples d'étanchéité - Feuilles bitumineuses, plastiques et élastomériques d'étanchéité de toiture - Détermination de la résistance à l'impact de la grêle
Abdichtungsbahnen - Bitumen-, Kunststoff- und Elastomerbahnen für Dachabdichtungen - Bestimmung des Widerstandes gegen Hagelschlag This European Standard was approved by CEN on 7 April 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13583:2012: ESIST EN 13583:2012
Part 1: Bitumen sheets for roof waterproofing
EN 1849-2, Flexible sheets for waterproofing — Determination of thickness and mass per unit area —
Part 2: Plastic and rubber sheets
prEN 10025-2:2011, Hot rolled products of structural steels — Part 2: Technical delivery conditions for non-alloy structural steels 1)
EN 13163, Thermal insulation products for buildings — Factory made products of expanded polystyrene (EPS) —
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...