SIST EN 480-4:2005

Admixtures for concrete, mortar and grout - Test methods - Part 4: Determination of bleeding of concrete

This European Standard describes a method to determine the relative quantity of mixing water that will bleed from a sample of freshly mixed concrete. This method applies to concrete mixes with aggregates having a maximum size up to 50 mm.

Zusatzmittel für Beton, Mörtel und Einpressmörtel -Prüfverfahren - Teil 4: Bestimmung der Wasserabsonderung des Betons (Bluten)

Diese Europäische Norm beschreibt ein Verfahren zur Bestimmung der Menge des Zugabewassers, die von einer Probe frisch gemischten Betons abgesondert wird. Dieses Verfahren gilt für Betonmischungen mit einem Größtkorn bis 50 mm der Gesteinskörnung.

Adjuvants pour béton, mortier et coulis - Méthodes d'essai -Partie 4: Détermination du ressuage du béton

Le présent document décrit une méthode de détermination de la quantité relative d'eau de gâchage susceptible de ressuer d'un échantillon de béton fraîchement malaxé. Cette méthode est applicable aux bétons contenant des granulats dont la taille maximale ne dépasse pas 50 mm.

Kemijski dodatki za beton, malto in injekcijsko maso – Preskusne metode – 4. del: Ugotavljanje izločanja vode iz betona

General Information

• Status: Published
• Publication Date: 30-Nov-2005
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: BBB - Concrete, reinforced concrete and prestressed concrete
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2005
• Due Date: 01-Dec-2005
• Completion Date: 01-Dec-2005
• Directive: 89/106/EEC - Construction products
• Mandate: M/128 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on products for concrete, mortar and grout
• Ref Project: EN 480-4:2005 - Admixtures for concrete, mortar and grout - Test methods - Part 4: Determination of bleeding of concrete

Relations

• Replaces: SIST EN 480-4:1998 - Admixtures for concrete, mortar and grout - Test methods - Part 4: Determination of bleeding of concrete
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 480-4:2005
01-december-2005
1DGRPHãþD
SIST EN 480-4:1998
.HPLMVNLGRGDWNL]DEHWRQPDOWRLQLQMHNFLMVNRPDVR±3UHVNXVQHPHWRGH±GHO
8JRWDYOMDQMHL]ORþDQMDYRGHL]EHWRQD
Admixtures for concrete, mortar and grout - Test methods - Part 4: Determination of
bleeding of concrete
Zusatzmittel für Beton, Mörtel und Einpressmörtel -Prüfverfahren - Teil 4: Bestimmung
der Wasserabsonderung des Betons (Bluten)
Adjuvants pour béton, mortier et coulis - Méthodes d'essai -Partie 4: Détermination du
ressuage du béton
Ta slovenski standard je istoveten z: EN 480-4:2005
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 480-4:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 480-4:2005

---------------------- Page: 2 ----------------------

SIST EN 480-4:2005
EUROPEAN STANDARD
EN 480-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2005
ICS 91.100.30 Supersedes EN 480-4:1996
English Version
Admixtures for concrete, mortar and grout - Test methods - Part
4: Determination of bleeding of concrete
Adjuvants pour béton, mortier et coulis - Méthodes d'essai - Zusatzmittel für Beton, Mörtel und Einpressmörtel -
Partie 4: Détermination du ressuage du béton Prüfverfahren - Teil 4: Bestimmung der
Wasserabsonderung des Betons (Bluten)
This European Standard was approved by CEN on 28 July 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 480-4:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 480-4:2005
EN 480-4:2005 (E)
Contents
Page
Foreword .3
1 Scope .4
2 Apparatus .4
3 Procedure .4
4 Results.5
5 Test report .5

2

---------------------- Page: 4 ----------------------

SIST EN 480-4:2005
EN 480-4:2005 (E)
Foreword
This European Standard (EN 480-4:2005) has been prepared by Technical Committee CEN/TC 104
“Concrete and related products”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2006, and conflicting national standards shall be withdrawn at the
latest by April 2006.
It has been drafted by Subcommittee 3 (SC 3) of TC 104 "Admixtures for concrete, mortar and grout".
This document is part of the series EN 480 "Admixtures for concrete, mortar and grout – Test methods" which
comprises the following
Part 1 Reference concrete and reference mortar for testing
Part 2 Determination of setting time
Part 4 Determination of bleeding of concrete
Part 5 Determination of capillary absorption
Part 6 Infrared analysis
Part 8 Determination of the conventional dry material content
Part 10 Determination of wa
...