iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 10232:1998

(Main)

Metallic materials - Tube (in full section) - Bend test

Metallic materials - Tube (in full section) - Bend test

This European Standard specifies a method for determining the ability of full- section metallic tubes of circular cross section to undergo plastic deformation in bending. It is inteded for tubes with an outside diameter not greater than 65mm although the range of the outside diameter for which this European Standardis applicable may be more exactly specified in the relevant Product Standard.

Metallische Werkstoffe - Rohr (Rohrabschnitt) - Biegeversuch

In dieser Euorpäischen Norm ist ein Verfahren festgelegt, mit dem die Eignung von Rohren aus metallischen Werkstoffen mit kreisförmigenm Querschnitt mit maximalem Aussendruchmesser von 65mm zur Biegung bei vollem Querschnitt bestimmt wird. Der Bereich der Aussendurchmesser, für den diese Europäische Norm zutrifft, kann genauer in der entsprechenden Erzeugnisnorm festgelegt sein

Matériaux métalliques - Tubes - Essai de cintrage sur tronçons

La présente norme européenne spécifie une méthode de détermination de l'aptitude a la déformation plastique par cintrage sur tronçon de tubes métalliques, de section circulaire. Elle est applicable aux tubes de diametre extérieur au plus égal a 65mm bien que la gamme de diametres extérieurs a laquelle s'applique la présente norme européenne peut etre détinie de façcon plus explicite dans la norme de produit concernée.

Kovinski materiali - Cev (narezana na dolžino) - Upogibni preskus

General Information

Status
Withdrawn
Publication Date
31-Jul-1998
Withdrawal Date
30-Jun-2005
ICS
77.040.10 - Mechanical testing of metals
Technical Committee
IFEK - Ferrous metals
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jul-2005
Due Date
01-Jul-2005
Completion Date
01-Jul-2005
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
EN 10232:1993 - Metallic materials - Tube (in full section) - Bend test

Relations

Replaced By
SIST EN ISO 8491:2004 - Metallic materials - Tube (in full section) - Bend test (ISO 8491:1998)
Effective Date
01-Jul-2005

Buy Standard

EN 10232:1998EN 10232:1998
PreviousNext
Standard
EN 10232:1998
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kovinski materiali - Cev (narezana na dolžino) - Upogibni preskusMetallische Werkstoffe - Rohr (Rohrabschnitt) - BiegeversuchMatériaux métalliques - Tubes - Essai de cintrage sur tronçonsMetallic materials - Tube (in full section) - Bend
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 6506-2:2019(Main)
Metallic materials - Brinell hardness test - Part 2: Verification and calibration of testing machines (ISO 6506-2:2017)
EN ISO 6506-2:2018

This document specifies methods of direct and indirect verification of testing machines used for
determining Brinell hardness in accordance with ISO 6506-1 and also specifies when these two types of
verification have to be performed.
The direct verification involves checking that individual machine performance parameters fall within
specified limits whereas the indirect verification utilizes hardness measurements of reference blocks,
calibrated in accordance with ISO 6506-3, to check the machine’s overall performance.
If a testing machine is also to be used for other methods of hardness testing, it has to be verified
independently for each method.
This document is applicable to both fixed location and portable hardness testing machines. For
machines that are incapable of satisfying the specified force-time profile, the direct verification of force
and testing cycle can be modified by the use of Annex B.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 4545-4:2018(Main)
Metallic materials - Knoop hardness test - Part 4: Table of hardness values (ISO 4545-4:2017)
EN ISO 4545-4:2018

This document gives a table for the calculation of Knoop hardness values for use in tests carried out in
accordance with ISO 4545-1.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 377:2017(Main)
Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
EN ISO 377:2017

This document specifies requirements for the identification, location and preparation of samples and test
pieces intended for mechanical tests on steel sections, bars, rod, flat products and tubular products as
defined in ISO 6929. If agreed in the order, this document can also apply to other metallic products. These
samples and test pieces are for use in tests that are carried out in conformity with the methods specified
in the product or material standard or, in the absence of this, in the standard for the test method.
Where the requirements of the order or product standard differ from those given in this document,
then the requirements of the order or product standard apply.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6508-1:2016(Main)
Metallic materials - Rockwell hardness test - Part 1: Test method (ISO 6508-1:2016)
EN ISO 6508-1:2016

This part of ISO 6508 specifies the method for Rockwell regular and Rockwell superficial hardness
tests for scales A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T, and 45T for metallic materials and is
applicable to stationary and portable hardness testing machines.
For specific materials and/or products, other specific International Standards apply (for instance,
ISO 3738-1 and ISO 4498).
NOTE Attention is drawn to the fact that the use of tungsten carbide composite for ball indenters is
considered to be the standard type of Rockwell indenter ball. Steel indenter balls are allowed to continue to be
used only when complying with Annex A

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16859-1:2016(Main)
Metallic materials - Leeb hardness test - Part 1: Test method (ISO 16859-1:2015)
EN ISO 16859-1:2015

This standard covers the determination of the Leeb hardness of metallic materials using six different Leeb scales (HLD, HLS, HLE, HLDL, HLC, HLG).

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16859-2:2016(Main)
Metallic materials - Leeb hardness test - Part 2: Verification and calibration of the testing devices (ISO 16859-2:2015)
EN ISO 16859-2:2015

This part of ISO 16859 specifies methods for direct and indirect verification of test instruments used for determining Leeb hardness in accordance with ISO 16859-1, and also describes when these two types of verification shall be performed.
The direct verification involves checking that individual instrument performance parameters fall within specified limits, whereas the indirect verification utilizes hardness measurements of reference test blocks, calibrated in accordance with ISO 16859-3, to check the overall performance of the instrument. The indirect method may be used on its own for the periodic performance checking in service.
NOTE°1 Direct verification of test instruments included in this standard can only be done where applicable reference values are provided by the instrument manufacturer.
NOTE°2 For testing in directions other than in direction of gravity, the measured hardness number will be biased. For such cases, the correction values shall be provided by the manufacturer.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 16859-3:2016(Main)
Metallic materials - Leeb hardness test - Part 3: Calibration of reference test blocks (ISO 16859-3:2015)
EN ISO 16859-3:2015

This part of ISO 16859 specified a method for the calibration of reference test blocks that are used for the indirect verification of Leeb hardness testers according to ISO 16859-2 and for the periodic checking according to ISO 16859-1.
The procedures necessary to ensure metrological traceability of the calibration machine are also specified.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14577-1:2015(Main)
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method (ISO 14577-1:2015)
EN ISO 14577-1:2015

This part of ISO 14577 specifies the method of instrumented indentation test for determination of
hardness and other materials parameters for the following three ranges:
— macro range: 2 N ≤ F ≤ 30 kN;
— micro range: 2 N > F; h > 0,2 μm;
— nano range: h ≤ 0,2 μm.
For the nano range, the mechanical deformation strongly depends on the real shape of indenter tip and the
calculated material parameters are significantly influenced by the contact area function of the indenter
used in the testing machine. Therefore, careful calibration of both instrument and indenter shape is
required in order to achieve an acceptable reproducibility of the materials parameters determined with
different machines.
The macro and micro ranges are distinguished by the test forces in relation to the indentation depth.
Attention is drawn to the fact that the micro range has an upper limit given by the test force (2 N) and a
lower limit given by the indentation depth of 0,2 μm.
The determination of hardness and other material parameters is given in Annex A.
At high contact pressures, damage to the indenter is possible. For this reason in the macro range,
hardmetal indenters are often used. For test pieces with very high hardness and modulus of elasticity,
permanent indenter deformation can occur and can be detected using suitable reference materials. It is
necessary that its influence on the test result be taken into account.
This test method can also be applied to thin metallic and non-metallic coatings and non-metallic
materials. In this case, it is recommended that the specifications in the relevant standards be taken into
account (see also 6.3 and ISO 14577-4).

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14577-2:2015(Main)
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 2: Verification and calibration of testing machines (ISO 14577-2:2015)
EN ISO 14577-2:2015

This part of ISO 14577 specifies the method of verification and calibration of testing machines for
carrying out the instrumented indentation test in accordance with ISO 14577-1:2015.
It describes a direct verification method for checking the main functions of the testing machine and an
indirect verification method suitable for the determination of the repeatability of the testing machine.
There is a requirement that the indirect method be used in addition to the direct method and for the
periodic routine checking of the testing machine in service.
It is a requirement that the indirect method of verification of the testing machine be carried out
independently for each test method.
This part of ISO 14577 is also applicable for transportable testing machines.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14577-3:2015(Main)
Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks (ISO 14577-3:2015)
EN ISO 14577-3:2015

This part of ISO 14577 specifies a method for the calibration of reference blocks to use for the indirect
verification of testing machines for the instrumented indentation test as specified in ISO 14577-2:2015.
NOTE The reference blocks can be calibrated in accordance with the field of application of the testing
machine or with the materials parameters which are being determined.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day