SIST EN ISO 377:2017/A1:2025
(Amendment)Steel and steel products - Location and preparation of samples and test pieces for mechanical testing - Amendment 1 (ISO 377:2017/Amd 1:2025)
Steel and steel products - Location and preparation of samples and test pieces for mechanical testing - Amendment 1 (ISO 377:2017/Amd 1:2025)
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben für mechanische Prüfungen - Änderung 1 (ISO 377:2017/Amd 1:2025)
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour essais mécaniques - Amendement 1 (ISO 377:2017/Amd 1:2025)
Jeklo in jekleni izdelki - Lokacija in priprava vzorcev ter preskušancev za mehansko preskušanje - Dopolnilo A1 (ISO 377:2017/Amd 1:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2025
Jeklo in jekleni izdelki - Lokacija in priprava vzorcev ter preskušancev za
mehansko preskušanje - Dopolnilo A1 (ISO 377:2017/Amd 1:2025)
Steel and steel products - Location and preparation of samples and test pieces for
mechanical testing - Amendment 1 (ISO 377:2017/Amd 1:2025)
Stahl und Stahlerzeugnisse - Lage und Vorbereitung von Probenabschnitten und Proben
für mechanische Prüfungen - Änderung 1 (ISO 377:2017/Amd 1:2025)
Acier et produits en acier - Position et préparation des échantillons et éprouvettes pour
essais mécaniques - Amendement 1 (ISO 377:2017/Amd 1:2025)
Ta slovenski standard je istoveten z: EN ISO 377:2017/A1:2025
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
77.140.01 Železni in jekleni izdelki na Iron and steel products in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 377:2017/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2025
EUROPÄISCHE NORM
ICS 77.040.10
English Version
Steel and steel products - Location and preparation of
samples and test pieces for mechanical testing -
Amendment 1 (ISO 377:2017/Amd 1:2025)
Acier et produits en acier - Position et préparation des Stahl und Stahlerzeugnisse - Lage und Vorbereitung
échantillons et éprouvettes pour essais mécaniques - von Probenabschnitten und Proben für mechanische
Amendement 1 (ISO 377:2017/Amd 1:2025) Prüfungen - Änderung 1 (ISO 377:2017/Amd 1:2025)
This amendment A1 modifies the European Standard EN ISO 377:2017; it was approved by CEN on 8 August 2025.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 377:2017/A1:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 377:2017/A1:2025) has been prepared by Technical Committee ISO/TC 17
"Steel" in collaboration with Technical Committee CEN/TC 459/SC 12 “General issues” the secretariat of
which is held by BSI.
This Amendment to the European Standard EN ISO 377:2017 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by February 2026,
and conflicting national standards shall be withdrawn at the latest by February 2026.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
T
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.