SIST EN ISO 11343:2019
(Main)Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact wedge conditions - Wedge impact method (ISO 11343:2019)
Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive bonds under impact wedge conditions - Wedge impact method (ISO 11343:2019)
This document specifies a dynamic impact wedge method for the determination of the cleavage
resistance under impact loading of high-strength adhesive bonds between two adherends, when tested
under specified conditions of preparation and testing. This test procedure does not provide design
information.
The method allows a choice of sheet metal or fibre reinforced plastic substrates corresponding to those
materials frequently used in industry, such as for automotive applications.
Klebstoffe - Bestimmung des dynamischen Keil-Schlag-Widerstandes von hochfesten Klebungen unter Keilschlagbelastung - Keil-Schlag-Verfahren (ISO 11343:2019)
Dieses Dokument legt ein dynamisches Keil-Schlag-Verfahren für die Bestimmung des Keil-Schlag-Widerstandes unter Schlagbelastung hochfester Klebungen zwischen zwei Substraten, die unter festgelegten Bedingungen hergestellt und geprüft werden, fest. Dieses Verfahren liefert keine Informationen für die Konstruktion.
Dieses Verfahren gestattet, Metallbleche oder faserverstärkte Kunststofffügewerkstoffe, die solchen entsprechen, die in der Industrie häufig, wie z. B. für den Automobilbau, eingesetzt werden, zu wählen.
Adhésifs - Détermination de la résistance dynamique au clivage de joints collés à haute résistance soumis aux conditions d'impact - Méthode d'impact au coin (ISO 11343:2019)
Le présent document spécifie une méthode d'essai d'impact au coin pour la détermination de la résistance au clivage de joints collés à haute résistance soumis à une charge dynamique entre deux supports collés, dans des conditions spécifiées de préparation et d'essai. Ce mode opératoire d'essai ne fournit pas d'informations relatives à la conception.
Cette méthode permet d'opter pour des substrats métalliques en tôle ou des substrats en plastique renforcé de fibres, qui correspondent aux matériaux fréquemment utilisés dans l'industrie, notamment l'industrie automobile.
Lepila - Ugotavljanje dinamične odpornosti proti cepitvi lepljenih spojev z veliko trdnostjo pod udarnimi klinom - Metoda z udarnim klinom (ISO 11343:2019)
Ta dokument določa metodo z udarnim klinom za ugotavljanje dinamične odpornosti proti cepitvi lepljenih spojev z veliko trdnostjo med lepljencema proti udarnim obremenitvam pri preskušanju pod določenimi pogoji za pripravo in preskušanje. Ta preskusni postopek ne podaja informacij o zasnovi.
Metoda omogoča izbiro pločevine ali z vlakni ojačanih plošč iz polimernih materialov, ki ustrezajo pogosto uporabljenim materialom v industriji, na primer za avtomobilsko uporabo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11343:2019
01-oktober-2019
Nadomešča:
SIST EN ISO 11343:2005
Lepila - Ugotavljanje dinamične odpornosti proti cepitvi lepljenih spojev z veliko
trdnostjo pod udarnimi klinom - Metoda z udarnim klinom (ISO 11343:2019)
Adhesives - Determination of dynamic resistance to cleavage of high-strength adhesive
bonds under impact wedge conditions - Wedge impact method (ISO 11343:2019)
Klebstoffe - Bestimmung des dynamischen Keil-Schlag-Widerstandes von hochfesten
Klebungen unter Keilschlagbelastung - Keil-Schlag-Verfahren (ISO 11343:2019)
Adhésifs - Détermination de la résistance dynamique au clivage de joints collés à haute
résistance soumis aux conditions d'impact - Méthode d'impact au coin (ISO 11343:2019)
Ta slovenski standard je istoveten z: EN ISO 11343:2019
ICS:
83.180 Lepila Adhesives
SIST EN ISO 11343:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11343:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 11343:2019
EN ISO 11343
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN ISO 11343:2005
English Version
Adhesives - Determination of dynamic resistance to
cleavage of high-strength adhesive bonds under impact
wedge conditions - Wedge impact method (ISO
11343:2019)
Adhésifs - Détermination de la résistance dynamique Klebstoffe - Bestimmung des dynamischen Keil-Schlag-
au clivage de joints collés à haute résistance soumis Widerstandes von hochfesten Klebungen unter
aux conditions d'impact - Méthode d'impact au coin Keilschlagbelastung - Keil-Schlag-Verfahren (ISO
(ISO 11343:2019) 11343:2019)
This European Standard was approved by CEN on 11 June 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11343:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11343:2019
EN ISO 11343:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11343:2019
EN ISO 11343:2019 (E)
European foreword
This document (EN ISO 11343:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by
UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall
be withdrawn at the latest by January 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11343:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11343:2019 has been approved by CEN as EN ISO 11343:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11343:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 11343:2019
INTERNATIONAL ISO
STANDARD 11343
Third edition
2019-06
Adhesives — Determination of
dynamic resistance to cleavage of
high-strength adhesive bonds under
impact wedge conditions — Wedge
impact method
Adhésifs — Détermination de la résistance dynamique au clivage de
joints collés à haute résistance soumis aux conditions d'impact —
Méthode d'impact au coin
Reference number
ISO 11343:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 11343:2019
ISO 11343:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11343:2019
ISO 11343:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Specimens . 4
7 Test procedure . 7
8 Expression of results . 7
9 Precision .11
10 Test report .11
© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11343:2019
ISO 11343:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This third edition cancels and replaces the second edition (ISO 11343:2003), which has been technically
revised. The main changes compared to the previous edition are as follows:
a) added new terms and definitions;
b) explicitly included usage of different test machines in apparatus;
c) added Note regarding signal filtering;
d) added representative points in force-time figures;
e) minor editorial changes.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11343:2019
INTERNATIONAL STANDARD ISO 11343:2019(E)
Adhesives — Determination of dynamic resistance to
cleavage of high-strength adhesive bonds under impact
wedge conditions — Wedge impact method
1 Scope
This document specifies a dynamic impact wedge method for the determination of the cleavage
resistance under impact loading of high-strength adhesive bonds between two adherends, when tested
under specified conditions of preparation and testing. This test procedure does not provide design
information.
The method allows a choice of sheet metal or fibre reinforced plastic substrates corresponding to those
materials frequently used in industry, such as for automotive applications.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 10365, Adhesives — Designation of main failure patterns
EN 13887, Structural adhesives — Guidelines for surface preparation of metals and plastics prior to
adhesive bonding
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
dynamic resistance to cleavage
force per unit width necessary to bring an adhesive joint to the point of failure by means of a stress
applied by a wedge moving between the two substrates of the joint, and thus separating the adherends
in a cleaving mode
Note 1 to entry: The dynamic resistance to cleavage is expressed in kilonewtons per metre.
3.2
cracking force
maximum force after which the force falls to a plateau
Note 1 to entry: The cracking force is expressed in newtons.
Note 2 to entry: Typically, it is also the highest force measured. It characterizes the beginning of cracking.
© ISO 2019 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 11343:2019
ISO 11343:2019(E)
3.3
cleavage force
momentary force during stable crack growth within the adhesive joint
Note 1 to entry: The cleavage force is expressed in newtons.
3.4
average cleavage force
average force of the plateau region, the stable crack growth zone of the adhesive joint
Note 1 to entry: The average cleavage
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.