iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60974-10:2014/A1:2015

(Amendment)

Arc welding equipment - Part 10: Electromagnetic comppatibility (EMC) requirements

Arc welding equipment - Part 10: Electromagnetic comppatibility (EMC) requirements

Lichtbogenschweißeinrichtungen - Teil 10: Anforderungen an die elektromagnetische Verträglichkeit (EMV)

Matériel de soudage à l’arc - Partie 10: Exigences de compatibilité électromagnétique (CEM)

Oprema za obločno varjenje - 10. del: Zahteve za elektromagnetno združljivost (EMC) - Dopolnilo A1

General Information

Status
Published
Publication Date
09-Nov-2015
ICS
25.160.30 - Welding equipment
33.100.01 - Electromagnetic compatibility in general
Technical Committee
I09 - Imaginarni 09
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Sep-2015
Due Date
06-Nov-2015
Completion Date
10-Nov-2015
Directive
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2014/30/EU - Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast)
Mandate
M/404 - Standardisation Mandate to CEN, CENELEC and ETSI for harmonized standard according to the Electro Magnetic Compatibility (EMC) Directive 2004/108/EC
Ref Project
EN 60974-10:2014/A1:2015 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements

Relations

Amends
SIST EN 60974-10:2014 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
Effective Date
01-Dec-2015
Replaced By
SIST EN IEC 60974-10:2022 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements (IEC 60974-10:2020)
Effective Date
14-Dec-2021
Replaced By
SIST EN IEC 60974-10:2022 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements (IEC 60974-10:2020)
Effective Date
07-Jun-2022
Revised
SIST EN IEC 60974-10:2022 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements (IEC 60974-10:2020)
Effective Date
23-Jan-2018
Amends
SIST EN 60974-10:2014 - Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
Effective Date
07-Jun-2022

Buy Standard

EN 60974-10:2014/A1:2015EN 60974-10:2014/A1:2015
PreviousNext
Amendment
EN 60974-10:2014/A1:2015
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
EN 60974-10:2014/A1:2015EN 60974-10:2014/A1:2015
PreviousNext
Amendment
EN 60974-10:2014/A1:2015
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60974-10:2014/A1:2015
01-december-2015
Oprema za obločno varjenje - 10. del: Zahteve za elektromagnetno združljivost
(EMC) - Dopolnilo A1
Arc welding equipment - Part 10: Electromagnetic comppatibility (EMC) requirements
Lichtbogenschweißeinrichtungen - Teil 10: Anforderungen an die elektromagnetische
Verträglichkeit (EMV)
Matériel de soudage à l’arc - Partie 10: Exigences de compatibilité électromagnétique
(CEM)
Ta slovenski standard je istoveten z: EN 60974-10:2014/A1:2015
ICS:
25.160.30 Varilna oprema Welding equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 60974-10:2014/A1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60974-10:2014/A1:2015

---------------------- Page: 2 ----------------------
SIST EN 60974-10:2014/A1:2015


EUROPEAN STANDARD EN 60974-10:2014/A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2015
ICS 25.160

English Version
Arc welding equipment - Part 10: Electromagnetic compatibility
(EMC) requirements
(IEC 60974-10:2014/A1:2015)
Matériel de soudage à l'arc - Partie 10: Exigences de Lichtbogenschweißeinrichtungen - Teil 10: Anforderungen
compatibilité électromagnétique (CEM) an die elektromagnetische Verträglichkeit (EMV)
(IEC 60974-10:2014/A1:2015) (IEC 60974-10:2014/A1:2015)
This amendment A1 modifies the European Standard EN 60974-10:2014; it was approved by CENELEC on 2015-07-24. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60974-10:2014/A1:2015 E

---------------------- Page: 3 ----------------------
SIST EN 60974-10:2014/A1:2015
EN 60974-10:2014/A1:2015
European Foreword
The text of document 26/549/CDV, future IEC 60974-10/A1, prepared by IEC/TC 26 "Electric welding"
was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60974-10:2014/A1:2015.

The following dates are fixed:
(dop) 2016-04-24
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-07-24
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive.

For the relationship with EU Directive see informative Annex ZZ, included in EN 60974-10:2014.

Endorsement notice
The text of the International Standard IEC 60974-10:2014/AMD 1:2015 was approved by CENELEC
as a European Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN 60974-10:2014/A1:2015



IEC 60974-10

®


Edition 3.0 2015-06




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




AM ENDMENT 1

AM ENDEMENT 1





Arc welding equipment –

Part 10: Electromagnetic compatibility (EMC) requirements




Matériel de soudage à l’arc –

Partie 10: Exigences de compatibilité électromagnétique (CEM)

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 25.160 ISBN 978-
...

SLOVENSKI STANDARD
SIST EN 60974-10:2014/A1:2015
01-december-2015
2SUHPD]DREORþQRYDUMHQMHGHO=DKWHYH]DHOHNWURPDJQHWQR]GUXåOMLYRVW
(0& 'RSROQLOR$
Arc welding equipment - Part 10: Electromagnetic comppatibility (EMC) requirements
Lichtbogenschweißeinrichtungen - Teil 10: Anforderungen an die elektromagnetische
Verträglichkeit (EMV)
Matériel de soudage à l’arc - Partie 10: Exigences de compatibilité électromagnétique
(CEM)
Ta slovenski standard je istoveten z: EN 60974-10:2014/A1:2015
ICS:
25.160.30 Varilna oprema Welding equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 60974-10:2014/A1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60974-10:2014/A1:2015

---------------------- Page: 2 ----------------------

SIST EN 60974-10:2014/A1:2015


EUROPEAN STANDARD EN 60974-10:2014/A1

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2015
ICS 25.160

English Version
Arc welding equipment - Part 10: Electromagnetic compatibility
(EMC) requirements
(IEC 60974-10:2014/A1:2015)
Matériel de soudage à l'arc - Partie 10: Exigences de Lichtbogenschweißeinrichtungen - Teil 10: Anforderungen
compatibilité électromagnétique (CEM) an die elektromagnetische Verträglichkeit (EMV)
(IEC 60974-10:2014/A1:2015) (IEC 60974-10:2014/A1:2015)
This amendment A1 modifies the European Standard EN 60974-10:2014; it was approved by CENELEC on 2015-07-24. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 60974-10:2014/A1:2015 E

---------------------- Page: 3 ----------------------

SIST EN 60974-10:2014/A1:2015
EN 60974-10:2014/A1:2015
European Foreword
The text of document 26/549/CDV, future IEC 60974-10/A1, prepared by IEC/TC 26 "Electric welding"
was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60974-10:2014/A1:2015.

The following dates are fixed:
(dop) 2016-04-24
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-07-24
standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive.

For the relationship with EU Directive see informative Annex ZZ, included in EN 60974-10:2014.

Endorsement notice
The text of the International Standard IEC 60974-10:2014/AMD 1:2015 was approved by CENELEC
as a European Standard without any modification.
2

---------------------- Page: 4 ----------------------

SIST EN 60974-10:2014/A1:2015



IEC 60974-10

®


Edition 3.0 2015-06




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE




AM ENDMENT 1

AM ENDEMENT 1





Arc welding equipment –

Part 10: Electromagnetic compatibility (EMC) requirements




Matériel de soudage à l’arc –

Partie 10: Exigences de compatibilité électromagnétique (CEM)

















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 25.160 ISBN 978-2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60974-10:2022(Main)
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements (IEC 60974-10:2020)
EN IEC 60974-10:2021

IEC 60974-10:2014 specifies  a) applicable standards and test methods for radio-frequency (RF) emissions;  b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker;  c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges.  This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. This third edition cancels and replaces the second edition published in 2007 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:  - inclusion of optional use of a decoupling network and a load outside the test chamber;  - inclusion of an alternative test setup for portable equipment;  - inclusion of test conditions for complex controls, liquid cooling systems and arc striking and stabilizing devices;  - update of the applicable limits related to the updated reference to CISPR 11;  - exclusion of the use of narrow band relaxations for RF emission limits;  - update of the applicable limits for harmonics and flicker and inclusion of flow-charts related to the updated reference to IEC 61000-3-11 and IEC 61000-3-12;  - update of the requirements for voltage dips related to the updated reference to IEC 61000-4-11 and IEC 61000-4-34;  - update of the informative annex for installation and use;  - inclusion of symbols to indicate the RF equipment class and restrictions for use.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62135-2:2022(Main)
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements (IEC 62135-2:2020)
EN IEC 62135-2:2021

This part of IEC 62135 is applicable to equipment for resistance welding and allied processes
which are connected to mains supplies with rated voltages up to 1 000 V AC RMS. This
document does not define safety requirements.
Resistance welding equipment type tested in accordance with, and which has met the
requirements of, this document, is deemed to be in compliance for all applications.
The frequency range covered is from 0 Hz to 400 GHz.
Arc welding equipment containing a radio receiver or transmitter is within the scope of this
document. Additional requirements for such equipment is specified in Annex D.
The radiated emission requirements in this document are not intended to be applicable to the
intentional transmissions from a radio transmitter as defined by the ITU nor to any spurious
emissions related to these intentional transmitters.
This product EMC standard for resistance welding equipment takes precedence over all
aspects of the generic standards and no additional EMC tests are required or necessary.
NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means
comparable to resistance welding equipment.
NOTE 2 Limit values are specified for only part of the frequency range.
Resistance welding equipment are classified as Class A and Class B equipment.
This part of IEC 62135 specifies
a) test methods to be used in conjunction with CISPR 11:2015, CISPR 11:2015/AMD1:2016
and CISPR 11:2015/AMD2:2019 to determine radio-frequency (RF) emission;
b) relevant standards and test methods for harmonic current emission, voltage fluctuation
and flicker;
c) additional requirements for equipment powered by internal or external batteries (Annex C).
NOTE 3 The limits in this document cannot, however, provide full protection against interference to radio and
television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e).
NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional
mitigation measures are sometimes employed to further reduce the electromagnetic emissions.
NOTE 5 The origins of the limit values in this document are summarized in Annex A.
This part of IEC 62135 also defines immunity requirements and test methods for continuous
and transient, conducted and radiated disturbances including electrostatic discharges.
NOTE 6 These requirements do not, however, cover extreme cases which are extremely rare.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62135-2:2015(Main)
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements
EN 62135-2:2015

This part of IEC 62135 is applicable to equipment for resistance welding and allied processes
which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This
standard does not define safety requirements.
Resistance welding equipment type tested in accordance with, and which has met the
requirements of, this standard, is deemed to be in compliance for all applications.
The frequency range covered is from 0 Hz to 400 GHz.
This product EMC standard for resistance welding equipment takes precedence over all
aspects of the generic standards and no additional EMC tests are required or necessary.
NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means
comparable to resistance welding equipment.
NOTE 2 Limit values are specified for only part of the frequency range.
Resistance welding equipment are classified as class A and class B equipment.
This part of IEC 62135 specifies
a) test methods to be used in conjunction with CISPR 11 to determine radiofrequency (RF)
emission;
b) relevant standards and test methods for harmonic current emission, voltage fluctuation
and flicker.
NOTE 3 The limits in this standard cannot, however, provide full protection against interference to radio and
television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e).
NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional
mitigation measures are sometimes employed to further reduce the electromagnetic emissions.
This part of IEC 62135 also defines immunity requirements and test methods for continuous
and transient, conducted and radiated disturbances including electrostatic discharges.
NOTE 5 These requirements do not, however, cover extreme cases which are extremely rare.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60974-10:2014(Main)
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
EN 60974-10:2014

EN IEC 60974-10 specifies a) applicable standards and test methods for radio-frequency (RF) emissions; b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker; c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. Arc welding equipment type tested in accordance with, and which has met the requirements of, this standard is considered to be in compliance for all applications.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60974-10:2022(Main)
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements (IEC 60974-10:2020)
EN IEC 60974-10:2021

IEC 60974-10:2014 specifies  a) applicable standards and test methods for radio-frequency (RF) emissions;  b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker;  c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges.  This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. This third edition cancels and replaces the second edition published in 2007 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:  - inclusion of optional use of a decoupling network and a load outside the test chamber;  - inclusion of an alternative test setup for portable equipment;  - inclusion of test conditions for complex controls, liquid cooling systems and arc striking and stabilizing devices;  - update of the applicable limits related to the updated reference to CISPR 11;  - exclusion of the use of narrow band relaxations for RF emission limits;  - update of the applicable limits for harmonics and flicker and inclusion of flow-charts related to the updated reference to IEC 61000-3-11 and IEC 61000-3-12;  - update of the requirements for voltage dips related to the updated reference to IEC 61000-4-11 and IEC 61000-4-34;  - update of the informative annex for installation and use;  - inclusion of symbols to indicate the RF equipment class and restrictions for use.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62135-2:2022(Main)
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements (IEC 62135-2:2020)
EN IEC 62135-2:2021

This part of IEC 62135 is applicable to equipment for resistance welding and allied processes
which are connected to mains supplies with rated voltages up to 1 000 V AC RMS. This
document does not define safety requirements.
Resistance welding equipment type tested in accordance with, and which has met the
requirements of, this document, is deemed to be in compliance for all applications.
The frequency range covered is from 0 Hz to 400 GHz.
Arc welding equipment containing a radio receiver or transmitter is within the scope of this
document. Additional requirements for such equipment is specified in Annex D.
The radiated emission requirements in this document are not intended to be applicable to the
intentional transmissions from a radio transmitter as defined by the ITU nor to any spurious
emissions related to these intentional transmitters.
This product EMC standard for resistance welding equipment takes precedence over all
aspects of the generic standards and no additional EMC tests are required or necessary.
NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means
comparable to resistance welding equipment.
NOTE 2 Limit values are specified for only part of the frequency range.
Resistance welding equipment are classified as Class A and Class B equipment.
This part of IEC 62135 specifies
a) test methods to be used in conjunction with CISPR 11:2015, CISPR 11:2015/AMD1:2016
and CISPR 11:2015/AMD2:2019 to determine radio-frequency (RF) emission;
b) relevant standards and test methods for harmonic current emission, voltage fluctuation
and flicker;
c) additional requirements for equipment powered by internal or external batteries (Annex C).
NOTE 3 The limits in this document cannot, however, provide full protection against interference to radio and
television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e).
NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional
mitigation measures are sometimes employed to further reduce the electromagnetic emissions.
NOTE 5 The origins of the limit values in this document are summarized in Annex A.
This part of IEC 62135 also defines immunity requirements and test methods for continuous
and transient, conducted and radiated disturbances including electrostatic discharges.
NOTE 6 These requirements do not, however, cover extreme cases which are extremely rare.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62135-2:2015(Main)
Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements
EN 62135-2:2015

This part of IEC 62135 is applicable to equipment for resistance welding and allied processes
which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This
standard does not define safety requirements.
Resistance welding equipment type tested in accordance with, and which has met the
requirements of, this standard, is deemed to be in compliance for all applications.
The frequency range covered is from 0 Hz to 400 GHz.
This product EMC standard for resistance welding equipment takes precedence over all
aspects of the generic standards and no additional EMC tests are required or necessary.
NOTE 1 Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means
comparable to resistance welding equipment.
NOTE 2 Limit values are specified for only part of the frequency range.
Resistance welding equipment are classified as class A and class B equipment.
This part of IEC 62135 specifies
a) test methods to be used in conjunction with CISPR 11 to determine radiofrequency (RF)
emission;
b) relevant standards and test methods for harmonic current emission, voltage fluctuation
and flicker.
NOTE 3 The limits in this standard cannot, however, provide full protection against interference to radio and
television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e).
NOTE 4 In special cases, when highly susceptible apparatus is being used in close proximity, additional
mitigation measures are sometimes employed to further reduce the electromagnetic emissions.
This part of IEC 62135 also defines immunity requirements and test methods for continuous
and transient, conducted and radiated disturbances including electrostatic discharges.
NOTE 5 These requirements do not, however, cover extreme cases which are extremely rare.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60974-10:2014(Main)
Arc welding equipment - Part 10: Electromagnetic compatibility (EMC) requirements
EN 60974-10:2014

EN IEC 60974-10 specifies a) applicable standards and test methods for radio-frequency (RF) emissions; b) applicable standards and test methods for harmonic current emission, voltage fluctuations and flicker; c) immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges. This standard is applicable to equipment for arc welding and allied processes, including power sources and ancillary equipment, for example wire feeders, liquid cooling systems and arc striking and stabilizing devices. Arc welding equipment type tested in accordance with, and which has met the requirements of, this standard is considered to be in compliance for all applications.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day