SIST EN 60317-55:2008

Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180

This part of IEC 60317 specifies the requirements of solderable enamelled round copper winding wire of class 180 with a dual coating. The underlying coating is based on polyurethane resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. The superimposed coating is based on polyamide resin. Class 180 is a thermal class that requires a minimum temperature index of 180 ºC and a heat shock temperature of at least 200 ºC. The temperature in degrees Celsius corresponding to the temperature index is not necessarily that at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: - Grade 1: 0,050 mm up to and including 1,600 mm; - Grade 2: 0,050 mm up to and including 1,600 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-1.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 55: Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan und darüber mit Polyamid, Klasse 180

Spécifications pour types particuliers de fils de bobinage -- Partie 55: Fil de section circulaire en cuivre émaillé avec polyuréthane brasable et avec surcouche polyamide, classe 180

La présente partie de la CEI 60317 spécifie les exigences concernant les fils de bobinage de section circulaire en cuivre émaillé de classe 180 avec un double revêtement. La sous-couche est à base de résine polyuréthane, qui peut être modifiée pourvu qu'elle conserve l'identité chimique de la résine initiale et réponde à toutes les exigences du fil. La surcouche est à base de résine polyamide.

Specifikacije za posebne vrste navijalnih žic - 55. del: S poliuretanom emajliran bakren okrogel vodnik, prekrit s poliamidom, za spajkanje, razred 180 (IEC 60317-55:2007)

General Information

• Status: Withdrawn
• Publication Date: 28-Jul-2008
• Withdrawal Date: 13-Nov-2016
• ICS: 29.060.10 - Wires
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 14-Nov-2016
• Due Date: 07-Dec-2016
• Completion Date: 14-Nov-2016
• Ref Project: EN 60317-55:2008 - Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180

Relations

• Revised: SIST EN 60317-55:2014 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180
• Effective Date: 06-May-2014
• Replaced By: SIST EN 60317-55:2014 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180
• Effective Date: 20-Mar-2012
• Replaced By: SIST EN 60317-55:2014 - Specifications for particular types of winding wires -- Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60317-55:2008
01-september-2008
Specifikacije za posebne vrste navijalnih žic - 55. del: S poliuretanom emajliran
bakren okrogel vodnik, prekrit s poliamidom, za spajkanje, razred 180 (IEC 60317-
55:2007)
Specifications for particular types of winding wires - Part 55: Solderable polyurethane
enamelled round copper wire overcoated with polyamide, Class 180
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 55:
Runddrähte aus Kupfer, verzinnbar, lackisoliert mit Polyurethan und darüber mit
Polyamid, Klasse 180
Spécifications pour types particuliers de fils de bobinage - Partie 55: Fil de section
circulaire en cuivre émaillé avec polyuréthane brasable et avec surcouche polyamide,
classe 180
Ta slovenski standard je istoveten z: EN 60317-55:2008
ICS:
29.060.10 Žice Wires
SIST EN 60317-55:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60317-55:2008

---------------------- Page: 2 ----------------------

SIST EN 60317-55:2008

EUROPEAN STANDARD
EN 60317-55

NORME EUROPÉENNE
March 2008
EUROPÄISCHE NORM

ICS 29.060.10


English version


Specifications for particular types of winding wires -
Part 55: Solderable polyurethane enamelled round copper wire
overcoated with polyamide, class 180
(IEC 60317-55:2007)


Spécifications pour types particuliers  Technische Lieferbedingungen
de fils de bobinage - für bestimmte Typen von Wickeldrähten -
Partie 55: Fil de section circulaire Teil 55: Runddrähte aus Kupfer,
en cuivre émaillé avec polyuréthane verzinnbar, lackisoliert mit Polyurethan
brasable et avec surcouche polyamide, und darüber mit Polyamid, Klasse 180
classe 180 (IEC 60317-55:2007)
(CEI 60317-55:2007)




This European Standard was approved by CENELEC on 2008-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-55:2008 E

---------------------- Page: 3 ----------------------

SIST EN 60317-55:2008
EN 60317-55:2008 - 2 -
Foreword
The text of document 55/1027/FDIS, future edition 1 of IEC 60317-55, prepared by IEC TC 55, Winding
wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60317-55 on 2008-02-01.
This standard is to be used in conjunction with EN 60317-0-1:1998.
It should be noted that the clause numbering in this standard is not continuous due to the deletion of tests
no longer a part of the EN 60317-0 series of specifications for general requirements. Additionally, a
placeholder is provided for future winding wire tests so as to maintain a separation from winding wire
requirements from those for packaging.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2008-11-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2011-02-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60317-55:2007 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60317-55:2008
- 3 - EN 60317-55:2008

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year
IEC 60317-0-1 1997 Specifications for particular types of winding EN 60317-0-1 1998
A1 1999 wires - A1 2000
A2 2005 Part 0-1: General requirements - Enamelled A2 2005
round copper wire

---------------------- Page: 5 ----------------------

SIST EN 60317-55:2008

---------------------- Page: 6 ----------------------

SIST EN 60317-55:2008
IEC 60317-55
Edition 1.0 2007-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –
Part 55: Solderable polyurethane enamelled round copper wire overcoated with
polyamide, class 180

Spécifications pour types particuliers de fils de bobinage –
Partie 55: Fil de section circulaire en cuivre émaillé avec polyuréthane brasable
et avec surcouche polyamide, classe 180

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
J
CODE PRIX
ICS 29.060.10 ISBN 2-8318-9408-5

---------------------- Page: 7 ----------------------

SIST EN 60317-55:2008
– 2 – 60317-55 © IEC:2007
CONTENTS
FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references .6
3 Definitions, general notes on methods of test and appearance .6
3.1 Definitions and general notes on methods of test .6
3.2 Appearance.7
4 Dimensions .7
5 Electrical resistance .7
6 Elongation .7
7 Springiness .7
8 Flexibility and adherence.7
9 Heat shock .7
10 Cut-through .7
11 Resistance to abrasion .7
12 Resistance to solvents.8
13 Breakdown voltage .8
14 Continuity of insulation .8
15 Temperature index .8
16 Resistance to refrigerants.9
17 Solderability .9
17.1 Nominal conductor diameters up to and including 0,100 mm .9
17.2 Nominal conductor diameters over 0,100 mm .9
18 Heat or solvent bonding.9
19 Dielectric dissipation factor.9
20 Resistance to transformer oil .9
21 Loss of mass .9
23 Pin hole test .9
30 Packaging .9

Table 1 – Resistance to abrasion.8

---------------------- Page: 8 ----------------------

SIST EN 60317-55:2008
60317-55 © IEC:2007 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________

SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –

Part 55: Solderable polyurethane enamelled round copper wire
overcoated with poly
...