SIST EN ISO 14271:2002
(Main)Vickers hardness testing of resistance spot, projection and seam welds (low load and microhardness) (ISO 14271:2000)
Vickers hardness testing of resistance spot, projection and seam welds (low load and microhardness) (ISO 14271:2000)
++TC forecasts updated (TCforecasts updating exercise.sj 00-11-14)++
Vickers-Härteprüfung von Widerstandspunkt-, Buckel- und Rollennahtschweißungen (Kleinlast- und Mikrohärtebereich) (ISO 14271:2000)
Diese Internationale Norm beschreibt das Verfahren für die Härteprüfung an geätzten Querschliffen von Wider-standspunkt-, Buckel- und Rollennahtschweißungen.
Das Ziel der Härteprüfung ist, die Vickershärte im Kleinlast- oder Mikrobereich in der Schweißlinse, in der Wärmeein-flusszone und im Grundwerkstoff von ferritischen und nicht-ferritischen Werkstoffen zu bestimmen an Schweißungen aus Blechen mit Dicken 3 0,5 mm.
Essai de dureté Vickers sur soudures par résistance par points, par bossages et a la molette (essai sous charge réduite et essai de microdureté) (ISO 14271:2000)
La présente Norme internationale spécifie les modes opératoires pour l'essai de dureté de sections gravées des soudures par résistance par points, à la molette et par bossages. Les essais de dureté visent à déterminer la dureté Vickers, sous charge réduite ou de microdureté, du noyau de soudure, de la zone affectée thermiquement et du métal de base des métaux ferreux ou non ferreux des soudures réalisées dans des tôles d'épaisseur supérieure ou égale à 0,5 mm.
Preskušanje trdote po Vickersu na uporovnih točkovnih, bradavičnih in kolutnih zvarih (majhna obremenitev in mikro trdota) (ISO 14271:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14271:2002
01-maj-2002
3UHVNXãDQMHWUGRWHSR9LFNHUVXQDXSRURYQLKWRþNRYQLKEUDGDYLþQLKLQNROXWQLK
]YDULK PDMKQDREUHPHQLWHYLQPLNURWUGRWD ,62
Vickers hardness testing of resistance spot, projection and seam welds (low load and
microhardness) (ISO 14271:2000)
Vickers-Härteprüfung von Widerstandspunkt-, Buckel- und Rollennahtschweißungen
(Kleinlast- und Mikrohärtebereich) (ISO 14271:2000)
Essai de dureté Vickers sur soudures par résistance par points, par bossages et a la
molette (essai sous charge réduite et essai de microdureté) (ISO 14271:2000)
Ta slovenski standard je istoveten z: EN ISO 14271:2001
ICS:
25.160.40 Varjeni spoji in vari Welded joints
SIST EN ISO 14271:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14271:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 14271:2002
EUROPEAN STANDARD
EN ISO 14271
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2001
ICS 25.160.40
English version
Vickers hardness testing of resistance spot, projection and
seam welds (low load and microhardness) (ISO 14271:2000)
Essai de dureté Vickers sur soudures par résistance par Vickers-Härteprüfung von Widerstandspunkt-, Buckel- und
points, par bossages et à la molette (essai sous charge Rollennahtschweißungen (Kleinlast- und
réduite et essai de microdureté) (ISO 14271:2000) Mikrohärtebereich) (ISO 14271:2000)
This European Standard was approved by CEN on 5 October 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14271:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14271:2002
EN ISO 14271:2001 (E)
CORRECTED 2002-01-02
Foreword
The text of the International Standard from Technical Committee IIW has been taken over as a
European Standard by Technical Committee CEN/TC 121 "Welding", the secretariat of which is held by
DS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2002, and conflicting national standards shall be
withdrawn at the latest by April 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 14271:2000 has been approved by CEN as a European
Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14271:2002
EN ISO 14271:2001 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of -any of these publications
apply to this European Standard only when incorporated in it by amendment or revision. For undated
references the latest edition of the publication referred to applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated by
(mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 6507-1 1997 Metallic materials - Vickers hardness EN ISO 6507-1 1997
test - Part 1: Test method
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14271:2002
---------------------- Page: 6 ----------------------
SIST EN ISO 14271:2002
INTERNATIONAL ISO
STANDARD 14271
First edition
2000-11-01
Vickers hardness testing of resistance
spot, projection and seam welds (low load
and microhardness)
Essai de dureté Vickers sur soudures par résistance par points, par
bossages et à la molette (essai sous charge réduite et essai de
microdureté)
Reference number
ISO 14271:2000(E)
©
ISO 2000
---------------------- Page: 7 ----------------------
SIST EN ISO 14271:2002
ISO 14271:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 14271:2002
ISO 14271:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bod
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.