D26.04 - Test Methods

SIGNIFICANCE AND USE
4.1 Solvents that have been depleted in stabilizer content can become acidic. Acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 Halogenated organic solvents may contain amine type (alkaline, aqueous extractable) acid accepting additives, neutral type (typically epoxide) acid accepting additives or both. This test method can determine the combined acid acceptance from both types of stabilizers. In addition, if the amine acid acceptance is determined by a separate procedure (see Test Methods D2106), the amount of neutral acid accepting stabilizers in a solvent can be calculated from the difference between combined and amine acid acceptance values.  
4.3 This test method may be used by producers and users to verify that a product is complying with acid acceptance product specifications or by users to monitor the acid accepting ability of a solvent in use.
SCOPE
1.1 This test method covers the determination of the total acid acceptance including amine and neutral type (alpha epoxide) stabilizers in halogenated organic solvents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method can be used to establish manufacturing and purchasing specifications. It can also be used to determine the condition of solvents in use.
SCOPE
1.1 This test method covers the determination of acidity in halogenated organic solvents and admixtures thereof. The alkalinity may be determined utilizing Test Methods D2106, by substituting the end point measured at pH 7 by bromothymol blue or pH meter.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is useful for the determination of the amount of acid acceptance contributed by amines or bases as compared to other acid-accepting compounds.
SCOPE
1.1 These test methods, where applicable, cover the determination of the acid acceptance of halogenated organic solvents due to the presence therein of an organic amine titratable by standard acid. These test methods are suitable for samples of 0.001 to 0.02 weight percent (10 ppm to 200 ppm) alkalinity as NaOH. Two test methods are covered as follows:  
1.1.1 Test Method A—pH Method, and  
1.1.2 Test Method B—Indicator Method.  
1.1.3 Test Method C—GC Method.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This practice covers the standard procedure for determining impurities, stabilizers, and assays of halogenated organic solvents and their admixtures by gas chromatography. It is not the intent of this practice to provide a specific method of gas chromatography, but rather it defines what is required for a user to demonstrate that a method to be used is valid. The use of this practice allows the user to use the most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analytes involved.
SCOPE
1.1 This practice covers the determination of impurities, stabilizers and assay of halogenated organic solvents and their admixtures by gas chromatography.  
1.2 It is not the intent of this practice to provide a specific method of gas chromatography. The intent of this practice is to define what is required for a user to demonstrate that a method to be used is valid. The reason for this approach, as opposed to stating a method, is that gas chromatography is such a dynamic field that methods are often obsolete by the time they are validated. The use of this practice allows the user to use most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analysis of halogenated organic solvents and their admixtures.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method provides an analysis in weight percent of the normal-propyl bromide concentration of virgin, formulated, or reclaimed normal-propyl bromide: compounds that co-elute with normal-propyl bromide or normal-heptane (internal standard) may interfere with this test method.
SCOPE
1.1 This test method provides a basis for the determination of the normal-propyl bromide (weight %) in the presence of stabilizers and impurities, in virgin or reclaimed normal-propyl bromide (nPB). The application range is from 50 wt % to 100 wt %.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 High water concentrations can have a detrimental effect on many uses of halogenated solvents.  
4.1.1 Water can cause corrosion and spotting when solvents are used for metal cleaning.  
4.1.2 Water can reduce the shelf life of aerosol formulations.  
4.1.3 Water can inhibit desired reactions when solvents are used in formulations.
SCOPE
1.1 These test methods describe the use of the Karl Fischer (KF) titration for determination of water in halogenated organic solvents and mixtures thereof. Water concentrations from 2 ppm to 1000 ppm can be determined in these solvents. Two test methods are covered as follows:  
1.1.1 Test Method A, Water Determination Using a Coulometric KF Titrator—The coulometric test method is known for its high degree of sensitivity (typically 2O) and should be the test method of choice if water concentrations are typically below 50 ppm or if only small amounts of sample are available for water determinations. This test method requires the use of equipment specifically designed for coulometric titrations.  
1.1.2 Test Method B, Water Determination Using a Volumetric KF Titrator—The volumetric test method is a more traditional approach to KF water determinations. Although titrators are specifically designed for KF volumetric determinations, many automatic titrators on the market can be adapted to perform KF titrations.  
1.2 Either of these test methods can be used to determine typical water concentrations (15 ppm to 500 ppm) found in halogenated solvents.  
1.3 These test methods recommend the use of commercially available Karl Fischer titrators and reagents.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Sections 11 and 15.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The pH of halogenated solvents varies according to the nature of stabilizers in the particular solvent. Solvents with alkaline stabilizers (amine-types) generally have pHs in the 7 to 11 range, whereas solvents containing neutral stabilizers (epoxide-types) generally have pHs in the 5 to 7 range.  
3.2 Virgin and reclaimed solvents should have pHs within these ranges, dependent upon the claimed method of stabilization. These values should be within the accepted limits as proposed by the producers of the original virgin solvent.  
3.3 A lowering of pH from the above values, on receipt or use, is cause for concern. In this event, solvents having epoxide stabilizers should be tested for acid acceptance; solvent having alkaline stabilizers should be tested for alkalinity.
SCOPE
1.1 This test method covers the measurement of the pH of water extractions of halogenated organic solvents and admixtures thereof. This test method is applicable for the determination of the pH of water extractions of virgin, reclaimed, or used solvents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Nonvolatile matter in solvents can adversely affect their cleaning properties. These test methods can be used to control soil contamination in the boiling solvent, which if allowed to become too high, can decrease the stability of the solvent.  
3.2 These test methods can be used to establish manufacturing and purchasing specifications.
SCOPE
1.1 These test methods cover the determination of nonvolatile matter in halogenated organic solvents and admixtures.  
1.2 Five test methods are covered, as follows:  
1.2.1 Test Method A—For halogenated organic solvents or admixtures having less than 50 ppm nonvolatile matter; or where precision better than ±10 ppm is required.  
1.2.2 Test Method B—For halogenated organic solvents or admixtures having more than 50 ppm nonvolatile matter or where precision of ±0.001 % (10 ppm) is satisfactory.  
1.2.3 Test Method C—For low-boiling halogenated organic solvents or their admixtures (for example, methylene chloride, trichlorotrifluoroethane) that may superheat and cause bumping while evaporating to dryness with steam. A precision of greater than ±10 ppm can be attained.  
1.2.4 Test Method D—For rapid measurement of nonvolatile matter in halogenated organic solvents and their admixtures and where precision better than ±10 ppm is required.  
1.2.5 Test Method E—For halogenated organic solvents or admixtures and where precision better than ±10 ppm is required.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is to be used as a guide in selecting or eliminating certain grades of perchloroethylene used for drycleaning fabrics or degreasing metal parts.
SCOPE
1.1 This test method covers the evaluation of the corrosiveness to copper metal by perchloroethylene.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 The density or specific gravity of a pure chlorinated solvent at a given temperature is constant. Density or specific gravity can be used in identification of materials, the assay of binary mixtures, and as an indication of purity of a given solvent.
SCOPE
1.1 These test methods cover the determination of the specific gravity of halogenated organic solvents and solvent admixtures. They define suitable apparatus and procedures and furnish details underlying the interpretation of test data and the selection of numerical limits for agreement among interested persons and agencies.  
1.2 Three methods are covered as follows:  
1.2.1 Method A,  specific gravity by means of a hydrometer.  
1.2.2 Method B,  specific gravity and density by means of a pycnometer.  
Note 1: In referee problems, Method B may be used.  
1.2.3 Method C,  specific gravity and density by means of an electronic densitometer.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
2.1 These test methods are useful for determining the appearance of halogenated hydrocarbons and their admixtures.
SCOPE
1.1 These test methods cover the visual determination of the physical appearance of admixtures containing halogenated hydrocarbons. These test methods are qualitative test methods.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
5.1 This test method gives valid comparisons of the evaporation rates of the subject materials. These comparisons are required for the determination of the suitability of a proposed material for specific cleaning applications.
SCOPE
1.1 This test method covers the measurement of the relative evaporation time of halogenated organic solvents and their admixtures. This test method is not applicable in the presence of excessive drafts or high-velocity air currents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 These test methods are used to establish manufacturing and purchasing specifications. These test methods will provide a means of determining the condition of the solvent in use. A high water soluble chloride level may indicate the start of solvent decomposition.
SCOPE
1.1 Test Methods 1, 2, and 3—These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride.  
1.2 Test Method 4—This test method covers the determination of chloride ion in halogenated organic solvents and their admixtures.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Free halogens will react with any residual moisture in a solvent to form acid. These acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 The presence of free halogens in halogenated solvents is often an indication that the stabilizers in the solvent system are breaking down.  
4.3 This test method provides a means of detecting the presence of free halogens in halogenated solvents and their admixtures.
SCOPE
1.1 This test method covers the evaluation of free halogens in halogenated organic solvents and their admixtures.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method allows for the determination of ionizable contaminants (expressed in terms of ppb of HCl) in trichlorotrifluoroethane via measurement of specific aqueous conductance.  
3.2 This test method can be used for establishing manufacturing and purchasing specifications.
SCOPE
1.1 This test method covers the determination of aqueous conductivity due to ionizable contaminants extracted from trichlorotrifluoroethane. The value of 1.9 μS/cm as maximum specific aqueous conductance corresponds to 0.1 ppm of chloride ion (100 ppb). It was calculated by putting the solvent specification of 0.1 ppm chloride into the equation of the subject method to find C2 − C1 equals 19.08. The specific conductance due to contaminants from the solvent was then calculated as follows:
1.2 The above is exclusive of the background specific conductance of the water used in the analysis.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Exception—Values are stated in inch-pound units in Fig. 1.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method determines ionizable chloride that can be aqueously extracted from trichlorotrifluoroethane.  
3.2 This test method can be used to establish production and purchasing specifications.
SCOPE
1.1 This test method covers the determination of chloride in trichlorotrifluoroethane and other halocarbons that are liquid at room temperature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Normally clothes cleaned with perchloroethylene will have a clean cloth odor. If a foreign odor is present, it may be objectionable.
SCOPE
1.1 This test method covers the detection of a residual odor in drycleaning-grade perchloroethylene.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 These tests are to be used as a guide in selecting or eliminating certain solvents or grades of solvents used for cleaning or degreasing metal parts.
SCOPE
1.1 This test method covers the evaluation of the corrosiveness to metals by halogenated organic solvents and their admixtures for cold cleaning applications.  
Note 1: The test method described herein is an adaptation of Test Method D130.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method determines the total acidity of trichlorotrifluoroethane by titration with alcoholic potassium hydroxide using phenolphthalein for an indicator.  
3.2 This test method can be used to develop production and purchasing specifications.
SCOPE
1.1 This test method covers the determination of total acidity in trichlorotrifluoroethane and other halocarbons that are liquid at room temperature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
2.1 Color may be indicative of the quality of the solvent because any color present is due to the presence of contaminants.
SCOPE
1.1 This test method covers the visual measurement of the color of halogenated organic solvents and their admixtures. It is valid for values of 50 platinum-cobalt (Pt-Co) units or less.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 Solvents that have been depleted in stabilizer content can become acidic. Acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 Halogenated organic solvents may contain amine type (alkaline, aqueous extractable) acid accepting additives, neutral type (typically epoxide) acid accepting additives or both. This test method can determine the combined acid acceptance from both types of stabilizers. In addition, if the amine acid acceptance is determined by a separate procedure (see Test Methods D2106), the amount of neutral acid accepting stabilizers in a solvent can be calculated from the difference between combined and amine acid acceptance values.  
4.3 This test method may be used by producers and users to verify that a product is complying with acid acceptance product specifications or by users to monitor the acid accepting ability of a solvent in use.
SCOPE
1.1 This test method covers the determination of the total acid acceptance including amine and neutral type (alpha epoxide) stabilizers in halogenated organic solvents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 High water concentrations can have a detrimental effect on many uses of halogenated solvents.  
4.1.1 Water can cause corrosion and spotting when solvents are used for metal cleaning.  
4.1.2 Water can reduce the shelf life of aerosol formulations.  
4.1.3 Water can inhibit desired reactions when solvents are used in formulations.
SCOPE
1.1 These test methods describe the use of the Karl Fischer (KF) titration for determination of water in halogenated organic solvents and mixtures thereof. Water concentrations from 2 to 1000 ppm can be determined in these solvents. Two test methods are covered as follows:  
1.1.1 Test Method A, Water Determination Using a Coulometric KF Titrator—The coulometric test method is known for its high degree of sensitivity (typically 2O) and should be the test method of choice if water concentrations are typically below 50 ppm or if only small amounts of sample are available for water determinations. This test method requires the use of equipment specifically designed for coulometric titrations.  
1.1.2 Test Method B, Water Determination Using a Volumetric KF Titrator—The volumetric test method is a more traditional approach to KF water determinations. Although titrators are specifically designed for KF volumetric determinations, many automatic titrators on the market can be adapted to perform KF titrations.  
1.2 Either of these test methods can be used to determine typical water concentrations (15 to 500 ppm) found in halogenated solvents.  
1.3 These test methods recommend the use of commercially available Karl Fischer titrators and reagents.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Sections 11 and 15.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method is useful for the determination of the amount of acid acceptance contributed by amines or bases as compared to other acid-accepting compounds.
SCOPE
1.1 These test methods, where applicable, cover the determination of the acid acceptance of halogenated organic solvents due to the presence therein of an organic amine titratable by standard acid. These test methods are suitable for samples of 0.001 to 0.02 weight percent (10 – 200 ppm) alkalinity as NaOH. Two test methods are covered as follows:  
1.1.1 Test Method A—pH Method, and  
1.1.2 Test Method B—Indicator Method.  
1.1.3 Test Method C—GC Method.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ABSTRACT
This practice covers the standard procedure for determining impurities, stabilizers, and assays of halogenated organic solvents and their admixtures by gas chromatography. It is not the intent of this practice to provide a specific method of gas chromatography, but rather it defines what is required for a user to demonstrate that a method to be used is valid. The use of this practice allows the user to use the most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analytes involved.
SCOPE
1.1 This practice covers the determination of impurities, stabilizers and assay of halogenated organic solvents and their admixtures by gas chromatography.  
1.2 It is not the intent of this practice to provide a specific method of gas chromatography. The intent of this practice is to define what is required for a user to demonstrate that a method to be used is valid. The reason for this approach, as opposed to stating a method, is that gas chromatography is such a dynamic field that methods are often obsolete by the time they are validated. The use of this practice allows the user to use most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analysis of halogenated organic solvents and their admixtures.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 This test method provides an analysis in weight percent of the normal-propyl bromide concentration of virgin, formulated, or reclaimed normal-propyl bromide: compounds that co-elute with normal-propyl bromide or normal-heptane (internal standard) may interfere with this test method.
SCOPE
1.1 This test method provides a basis for the determination of the normal-propyl bromide (weight %) in the presence of stabilizers and impurities, in virgin or reclaimed normal-propyl bromide (nPB). The application range is from 50 to 100 wt %.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 The pH of halogenated solvents varies according to the nature of stabilizers in the particular solvent. Solvents with alkaline stabilizers (amine-types) generally have pHs in the 7 to 11 range, whereas solvents containing neutral stabilizers (epoxide-types) generally have pHs in the 5 to 7 range.  
3.2 Virgin and reclaimed solvents should have pHs within these ranges, dependent upon the claimed method of stabilization. These values should be within the accepted limits as proposed by the producers of the original virgin solvent.  
3.3 A lowering of pH from the above values, on receipt or use, is cause for concern. In this event, solvents having epoxide stabilizers should be tested for acid acceptance; solvent having alkaline stabilizers should be tested for alkalinity.
SCOPE
1.1 This test method covers the measurement of the pH of water extractions of halogenated organic solvents and admixtures thereof. This test method is applicable for the determination of the pH of water extractions of virgin, reclaimed, or used solvents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 This test method can be used to establish manufacturing and purchasing specifications. It can also be used to determine the condition of solvents in use.
SCOPE
1.1 This test method covers the determination of acidity in halogenated organic solvents and admixtures thereof. The alkalinity may be determined utilizing Test Methods D2106, by substituting the end point measured at pH 7 by bromothymol blue or pH meter.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

SIGNIFICANCE AND USE
4.1 This test method is to be used as a guide in selecting or eliminating certain grades of perchloroethylene used for drycleaning fabrics or degreasing metal parts.
SCOPE
1.1 This test method covers the evaluation of the corrosiveness to copper metal by perchloroethylene.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 Nonvolatile matter in solvents can adversely affect their cleaning properties. These test methods can be used to control soil contamination in the boiling solvent, which if allowed to become too high, can decrease the stability of the solvent.  
3.2 These test methods can be used to establish manufacturing and purchasing specifications.
SCOPE
1.1 These test methods cover the determination of nonvolatile matter in halogenated organic solvents and admixtures.  
1.2 Five test methods are covered, as follows:  
1.2.1 Test Method A—For halogenated organic solvents or admixtures having less than 50 ppm nonvolatile matter; or where precision better than ±10 ppm is required.  
1.2.2 Test Method B—For halogenated organic solvents or admixtures having more than 50 ppm nonvolatile matter or where precision of ±0.001 % (10 ppm) is satisfactory.  
1.2.3 Test Method C—For low-boiling halogenated organic solvents or their admixtures (for example, methylene chloride, trichlorotrifluoroethane) that may superheat and cause bumping while evaporating to dryness with steam. A precision of greater than ±10 ppm can be attained.  
1.2.4 Test Method D—For rapid measurement of nonvolatile matter in halogenated organic solvents and their admixtures and where precision better than ±10 ppm is required.  
1.2.5 Test Method E—For halogenated organic solvents or admixtures and where precision better than ±10 ppm is required.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 Free halogens will react with any residual moisture in a solvent to form acid. These acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 The presence of free halogens in halogenated solvents is often an indication that the stabilizers in the solvent system are breaking down.  
4.3 This test method provides a means of detecting the presence of free halogens in halogenated solvents and their admixtures.
SCOPE
1.1 This test method covers the evaluation of free halogens in halogenated organic solvents and their admixtures.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 This test method determines ionizable chloride that can be aqueously extracted from trichlorotrifluoroethane.  
3.2 This test method can be used to establish production and purchasing specifications.
SCOPE
1.1 This test method covers the determination of chloride in trichlorotrifluoroethane and other halocarbons that are liquid at room temperature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 These tests are to be used as a guide in selecting or eliminating certain solvents or grades of solvents used for cleaning or degreasing metal parts.
SCOPE
1.1 This test method covers the evaluation of the corrosiveness to metals by halogenated organic solvents and their admixtures for cold cleaning applications.  
Note 1: The test method described herein is an adaptation of Test Method D130.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 These test methods are used to establish manufacturing and purchasing specifications. These test methods will provide a means of determining the condition of the solvent in use. A high water soluble chloride level may indicate the start of solvent decomposition.
SCOPE
1.1 Test Methods 1, 2, and 3—These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride.  
1.2 Test Method 4—This test method covers the determination of chloride ion in halogenated organic solvents and their admixtures.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.

SIGNIFICANCE AND USE
5.1 This test method gives valid comparisons of the evaporation rates of the subject materials. These comparisons are required for the determination of the suitability of a proposed material for specific cleaning applications.
SCOPE
1.1 This test method covers the measurement of the relative evaporation time of halogenated organic solvents and their admixtures. This test method is not applicable in the presence of excessive drafts or high-velocity air currents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
3.1 This test method allows for the determination of ionizable contaminants (expressed in terms of ppb of HCl) in trichlorotrifluoroethane via measurement of specific aqueous conductance.  
3.2 This test method can be used for establishing manufacturing and purchasing specifications.
SCOPE
1.1 This test method covers the determination of aqueous conductivity due to ionizable contaminants extracted from trichlorotrifluoroethane. The value of 1.9 μS/cm as maximum specific aqueous conductance corresponds to 0.1 ppm of chloride ion (100 ppb). It was calculated by putting the solvent specification of 0.1 ppm chloride into the equation of the subject method to find C2 − C1 equals 19.08. The specific conductance due to contaminants from the solvent was then calculated as follows:
1.2 The above is exclusive of the background specific conductance of the water used in the analysis.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Exception—Values are stated in inch-pound units in Fig. 1.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.

SIGNIFICANCE AND USE
4.1 Normally clothes cleaned with perchloroethylene will have a clean cloth odor. If a foreign odor is present, it may be objectionable.
SCOPE
1.1 This test method covers the detection of a residual odor in drycleaning-grade perchloroethylene.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

SIGNIFICANCE AND USE
3.1 This test method determines the total acidity of trichlorotrifluoroethane by titration with alcoholic potassium hydroxide using phenolphthalein for an indicator.  
3.2 This test method can be used to develop production and purchasing specifications.
SCOPE
1.1 This test method covers the determination of total acidity in trichlorotrifluoroethane and other halocarbons that are liquid at room temperature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.

SIGNIFICANCE AND USE
2.1 Color may be indicative of the quality of the solvent because any color present is due to the presence of contaminants.
SCOPE
1.1 This test method covers the visual measurement of the color of halogenated organic solvents and their admixtures. It is valid for values of 50 platinum-cobalt (Pt-Co) units or less.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
2.1 These test methods are useful for determining the appearance of halogenated hydrocarbons and their admixtures.
SCOPE
1.1 These test methods cover the visual determination of the physical appearance of admixtures containing halogenated hydrocarbons. These test methods are qualitative test methods.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 The density or specific gravity of a pure chlorinated solvent at a given temperature is constant. Density or specific gravity can be used in identification of materials, the assay of binary mixtures, and as an indication of purity of a given solvent.
SCOPE
1.1 These test methods cover the determination of the specific gravity of halogenated organic solvents and solvent admixtures. They define suitable apparatus and procedures and furnish details underlying the interpretation of test data and the selection of numerical limits for agreement among interested persons and agencies.  
1.2 Three methods are covered as follows:  
1.2.1 Method A,  specific gravity by means of a hydrometer.  
1.2.2 Method B,  specific gravity and density by means of a pycnometer.  
Note 1: In referee problems, Method B may be used.  
1.2.3 Method C,  specific gravity and density by means of an electronic densitometer.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
4.1 Solvents that have been depleted in stabilizer content can become acidic. Acids can cause corrosion to process and storage equipment used for halogenated solvents.  
4.2 Halogenated organic solvents may contain amine type (alkaline, aqueous extractable) acid accepting additives, neutral type (typically epoxide) acid accepting additives or both. This test method can determine the combined acid acceptance from both types of stabilizers. In addition, if the amine acid acceptance is determined by a separate procedure (see Test Methods D2106), the amount of neutral acid accepting stabilizers in a solvent can be calculated from the difference between combined and amine acid acceptance values.  
4.3 This test method may be used by producers and users to verify that a product is complying with acid acceptance product specifications or by users to monitor the acid accepting ability of a solvent in use.
SCOPE
1.1 This test method covers the determination of the total acid acceptance including amine and neutral type (alpha epoxide) stabilizers in halogenated organic solvents.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

SIGNIFICANCE AND USE
4.1 This test method is useful for the determination of the amount of acid acceptance contributed by amines or bases as compared to other acid-accepting compounds.
SCOPE
1.1 These test methods, where applicable, cover the determination of the acid acceptance of halogenated organic solvents due to the presence therein of an organic amine titratable by standard acid. These test methods are suitable for samples of 0.001 to 0.02 weight percent (10 – 200 ppm) alkalinity as NaOH. Two test methods are covered as follows:  
1.1.1 Test Method A—pH Method, and  
1.1.2 Test Method B—Indicator Method.  
1.1.3 Test Method C—GC Method.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This practice covers the standard procedure for determining impurities, stabilizers, and assays of halogenated organic solvents and their admixtures by gas chromatography. It is not the intent of this practice to provide a specific method of gas chromatography, but rather it defines what is required for a user to demonstrate that a method to be used is valid. The use of this practice allows the user to use the most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analytes involved.
SCOPE
1.1 This practice covers the determination of impurities, stabilizers and assay of halogenated organic solvents and their admixtures by gas chromatography.
1.2 It is not the intent of this practice to provide a specific method of gas chromatography. The intent of this practice is to define what is required for a user to demonstrate that a method to be used is valid. The reason for this approach, as opposed to stating a method, is that gas chromatography is such a dynamic field that methods are often obsolete by the time they are validated. The use of this practice allows the user to use most effective technology and demonstrate that the method in use complies with a standard practice and is valid for the analysis of halogenated organic solvents and their admixtures.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method provides an analysis in weight percent of the normal-propyl bromide concentration of virgin, formulated, or reclaimed normal-propyl bromide: compounds that co-elute with normal-propyl bromide or normal-heptane (internal standard) may interfere with this test method.
SCOPE
1.1 This test method provides a basis for the determination of the normal-propyl bromide (weight %) in the presence of stabilizers and impurities, in virgin or reclaimed normal-propyl bromide (nPB). The application range is from 50 to 100 wt %.

SIGNIFICANCE AND USE
The pH of halogenated solvents varies according to the nature of stabilizers in the particular solvent. Solvents with alkaline stabilizers (amine-types) generally have pHs in the 7 to 11 range, whereas solvents containing neutral stabilizers (epoxide-types) generally have pHs in the 5 to 7 range.
Virgin and reclaimed solvents should have pHs within these ranges, dependent upon the claimed method of stabilization. These values should be within the accepted limits as proposed by the producers of the original virgin solvent.
A lowering of pH from the above values, on receipt or use, is cause for concern. In this event, solvents having epoxide stabilizers should be tested for acid acceptance; solvent having alkaline stabilizers should be tested for alkalinity.
SCOPE
1.1 This test method covers the measurement of the pH of water extractions of halogenated organic solvents and admixtures thereof. This test method is applicable for the determination of the pH of water extractions of virgin, reclaimed, or used solvents.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
High water concentrations can have a detrimental effect on many uses of halogenated solvents.
Water can cause corrosion and spotting when solvents are used for metal cleaning.
Water can reduce the shelf life of aerosol formulations.
Water can inhibit desired reactions when solvents are used in formulations.
SCOPE
1.1 These test methods describe the use of the Karl Fischer (KF) titration for determination of water in halogenated organic solvents and mixtures thereof. Water concentrations from 2 to 1000 ppm can be determined in these solvents. Two test methods are covered as follows:
1.1.1 Test Method A, Water Determination Using a Coulometric KF Titrator—The coulometric test method is known for its high degree of sensitivity (typically  10 μg H2O) and should be the test method of choice if water concentrations are typically below 50 ppm or if only small amounts of sample are available for water determinations. This test method requires the use of equipment specifically designed for coulometric titrations.
1.1.2 Test Method B, Water Determination Using a Volumetric KF Titrator—The volumetric test method is a more traditional approach to KF water determinations. Although titrators are specifically designed for KF volumetric determinations, many automatic titrators on the market can be adapted to perform KF titrations.
1.2 Either of these test methods can be used to determine typical water concentrations (15 to 500 ppm) found in halogenated solvents.  
1.3 These test methods recommend the use of commercially available Karl Fischer titrators and reagents.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Sections 11 and 15.

SIGNIFICANCE AND USE
Nonvolatile matter in solvents can adversely affect their cleaning properties. These test methods can be used to control soil contamination in the boiling solvent, which if allowed to become too high, can decrease the stability of the solvent.
These test methods can be used to establish manufacturing and purchasing specifications.
SCOPE
1.1 These test methods cover the determination of nonvolatile matter in halogenated organic solvents and admixtures.
1.2 Five test methods are covered, as follows:
1.2.1 Test Method A—For halogenated organic solvents or admixtures having less than 50 ppm nonvolatile matter; or where precision better than ±10 ppm is required.
1.2.2 Test Method B—For halogenated organic solvents or admixtures having more than 50 ppm nonvolatile matter or where precision of ±0.001 % (10 ppm) is satisfactory.
1.2.3 Test Method C—For low-boiling halogenated organic solvents or their admixtures (for example, methylene chloride, trichlorotrifluoroethane) that may superheat and cause bumping while evaporating to dryness with steam. A precision of greater than± 10 ppm can be attained.
1.2.4 Test Method D—For rapid measurement of nonvolatile matter in halogenated organic solvents and their admixtures and where precision better than ±10 ppm is required.
1.2.5 Test Method E—For halogenated organic solvents or admixtures and where precision better than ±10 ppm is required.
1.3 The values stated in SI units are to be regarded as the standard.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method is to be used as a guide in selecting or eliminating certain grades of perchloroethylene used for drycleaning fabrics or degreasing metal parts.
SCOPE
1.1 This test method covers the evaluation of the corrosiveness to copper metal by perchloroethylene.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
This test method can be used to establish manufacturing and purchasing specifications. It can also be used to determine the condition of solvents in use.
SCOPE
1.1 This test method covers the determination of acidity in halogenated organic solvents and admixtures thereof. The alkalinity may be determined utilizing Test Method D2106, by substituting the end point measured at pH 7 by bromothymol blue or pH meter.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

SIGNIFICANCE AND USE
These test methods are used to establish manufacturing and purchasing specifications. These test methods will provide a means of determining the condition of the solvent in use. A high water soluble chloride level may indicate the start of solvent decomposition.
SCOPE
1.1 Test Methods 1, 2, and 3—These test methods cover the determination of water-extractable halide ion in halogenated organic solvents and their admixtures. Fluoride ion is not measured due to the solubility of silver fluoride.
1.2 Test Method 4—This test method covers the determination of chloride ion in halogenated organic solvents and their admixtures.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.