D18.93 - Terminology for Soil, Rock and Contained Fluids

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minu...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
3.1 Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
3.2 Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.  
3.3 See Appendix X1 for References.  
3.4 Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
3.5 A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
3.5.1 No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.  
3.5.2 The symbols presented are examples; therefore, other symbols are acceptable.  
3.5.3 See Appendix X2 for ISRM Symbols.  
3.6 A number of definitions indicate the units of measurements in brackets and which follow the symbol(s) if given. The applicable units are indicated by italic capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter4
M—Mass, such as kilogram, gram
T—Time, such as second, minute  
3.6.1 Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”  
3.6.2 Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per min...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.  
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.  
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.

SIGNIFICANCE AND USE
Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.
Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.
See Appendix X1 for References.  
A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.
The symbols presented are examples; therefore, other symbols are acceptable.
See Appendix X2 for Symbols.  
A number of definitions indicate the units of measurements in parentheses and which follow the symbol(s) if given. The applicable units are indicated by bold capital letters, as follows:
DDimensionless
FForce, such as pound-force, ton-force, newton
LLength, such as inch, foot, millimeter, and meter
MMass, such as kilogram, gram
TTime, such as second, minute
Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”
Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1may be expressed in feet per minute, meters per second, etc.
Where synonymous terms are cross-referenced, the definition is usually included with the earlier term alphabetically. Where this is not the case, the later term is the more significant.
Definitions marked with (...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.

SIGNIFICANCE AND USE
Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.
Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.
See Appendix X1 for References.  
A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.
The symbols presented are examples; therefore, other symbols are acceptable.
See Appendix X2 for Symbols.  
A number of definitions indicate the units of measurements in parentheses and which follow the symbol(s) if given. The applicable units are indicated by bold capital letters, as follows:
DDimensionless
FForce, such as pound-force, ton-force, newton
LLength, such as inch, foot, millimeter, and meter
MMass, such as kilogram, gram
TTime, such as second, minute
Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”
Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1may be expressed in feet per minute, meters per second, etc.
Where synonymous terms are cross-referenced, the definition is usually included with the earlier term alphabetically. Where this is not the case, the later term is the more significant.
Definitions marked with (...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.
1.3 Definitions of terms relating to frozen soils are contained in Terminology D7099.

SIGNIFICANCE AND USE
Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.
Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.
See Appendix X1 for References.  
A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.
The symbols presented are examples; therefore, other symbols are acceptable.
See Appendix X2 for Symbols.  
A number of definitions indicate the units of measurements in parentheses and which follow the symbol(s) if given. The applicable units are indicated by bold capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter
M—Mass, such as kilogram, gram
T—Time, such as second, minute
Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”
Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minute, meters per second, etc.
Where synonymous terms are cross-referenced, the definition is usually included with the earlier term alphabetically. Where this is not the case, the later term is the more significant.
Definitions marked...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.
1.3 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SIGNIFICANCE AND USE
Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.
Terms that are defined in some textbooks may differ slightly from those in this terminology standard. Definitions in this terminology standard are to be regarded as correct for ASTM usage.
See Appendix X1 for References.  
A number of the definitions include symbols. The symbols appear in italics immediately after the name of the term.  
No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term.
The symbols presented are examples; therefore, other symbols are acceptable.
See Appendix X2 for Symbols.  
A number of definitions indicate the units of measurements in parentheses and which follow the symbol(s) if given. The applicable units are indicated by bold capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter
M—Mass, such as kilogram, gram
T—Time, such as second, minute
Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”
Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minute, meters per second, etc.
Where synonymous terms are cross-referenced, the definition is usually included with the earlier term alphabetically. Where this is not the case, the later term is the more significant.
Definitions marked...
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.
1.3 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SIGNIFICANCE AND USE
Definitions in this standard are to be regarded as the correct ones for terms found in other ASTM standards of Committee D18. Certain terms may be found in more than one standard issued under the jurisdiction of this committee and many of these terms have been placed in this standard.  
Terms that are defined in some textbooks may differ slightly from those in this standard. Definitions in Terminology D 653 are to be regarded as correct for ASTM usage
A number of the definitions include symbols and indicate the units of measurement. The symbols appear in italics immediately after the name of the term, followed by the unit in parentheses. No significance should be placed on the order in which the symbols are presented where two or more are given for an individual term. The applicable units are indicated by capital letters, as follows:
D—Dimensionless
F—Force, such as pound-force, ton-force, newton
L—Length, such as inch, foot, millimeter, and meter
M—Mass, such as kilogram, gram
T—Time, such as second, minute
Positive exponents designate multiples in the numerator. Negative exponents designate multiples in the denominator. Degrees of angle are indicated as “degrees.”
Expressing the units either in SI or the inch-pound system has been purposely omitted in order to leave the choice of the system and specific unit to the engineer and the particular application, for example:
FL−2—may be expressed in pounds-force per square inch, kilopascals, tons per square foot, etc.
LT−1—may be expressed in feet per minute, meters per second, etc.
Where synonymous terms are cross-referenced, the definition is usually included with the earlier term alphabetically. Where this is not the case, the later term is the more significant.
Definitions marked with (ISRM) are included for the convenience of the user and were taken directly from the International Society for Rock Mechanics (see X1.3).  
See Appendixes for References (X1) and Symbols (X2).
SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
p>1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.
1.4 Definitions of terms relating to frozen soils are contained in Terminology D 7099.

SCOPE
1.1 These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.
1.2 This standard defines terms related to soil, rock, and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.
1.3 These terms define many words found in the Terminology section of standards of ASTM Committee D18.

SCOPE
1.1 This practice provides a listing of keywords covering the broad subject areas applicable for papers and reports relating to soil and rock mechanics and engineering. The terms included in the listing include words and combinations of words that have significant value in indexing and retrieving technical information from the literature.  
1.2 Terms (descriptors) conveying broad, generic concepts as well as specific concepts are contained in the listing.