CEN/SS B02 - Structures

This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction.
NOTE            This test procedure is not intended to determine the absolute maximum value of loss of mass and volume of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified parameters.

This document specifies a method for the determination of the influence of water on the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in joints in buildings and civil engineering works.

This document specifies a method for the determination of the resistance to compression of sealants used in joints in buildings and civil engineering works.

This document defines technical terms for self-levelling and gun-grade (gunnable) sealants for above-ground exposed structures.

The document specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in buildings and civil engineering works.

2010-11-09 EMA: // final draft provided to ISO/CS according to notification received in dataservice on 2010-11-09.

TC - EN implementation of ISO Corrigendum ISO 9047:2001/Cor 1:2009.

ISO 10590:2005 specifies a method for the determination of the influence of water immersion on the adhesion/cohesion properties at maintained extension of sealants used in joints in building construction.

ISO 8340:2005 specifies a method for the determination of the tensile properties at maintained extension of sealants used in joints in building construction.

ISO 8339:2005 specifies a method for the determination of the tensile properties of sealants used in joints in building construction.

This International Standard specifies the types and classes of sealants used in building construction according to their applications and performance characteristics.
The requirements and respective test methods for the different classes are also given.

This International Standard specifies a method for the determination of the resistance to flow of sealants, by loss of cohesion under their own weight. These sealants are used in joints in vertical surfaces in building construction.

This International Standard specifies a method for the determination of the elastic recovery of sealants after maintained  extension.

This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants
with predominantly elastic behaviour which are used in joints in building construction.

ISO 11431:2002 specifies a method for the determination of the adhesion/cohesion properties of sealants after cyclic exposure to heat and artificial light followed by a period of exposure to water at a defined temperature.

ISO 11431:2002 specifies a method for the determination of the adhesion/cohesion properties of sealants after cyclic exposure to heat and artificial light followed by a period of exposure to water at a defined temperature.

ISO 10563:2017 specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction.

ISO 10591:2005 specifies a method for the determination of the influence of water on the adhesion cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.

ISO 11432:2005 specifies a method for the determination of the resistance to compression of sealants used in joints in building construction.

ISO 6927:2012 defines technical terms for self-levelling and gun-grade (gunnable) sealants for above ground exposed structures. It is not applicable to sealants used in roads and airfields, sealants for water retaining structures, or structural glazing sealants.

This International Standard specifies a method for the determination of the adhesion/cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.

ISO 10563:2005 specifies a method for the determination of the change of mass and the change of volume of sealants used in joints in building construction. It is not suitable for self-levelling sealants.

Defines technical terms for sealants for building purposes and applies to joints filled with hardening, plastic or elastic materials which are not preformed. Does not include all necessary technical terms on jointing products. Material properties are defined in general terms without reference to related quantitative aspects.

Applies to all sealants regardless of the kind of packages in which they are supplied or from which they are applied to the joint in buildings. A defined volume of sealant is extruded from a standardized device under defined conditions by means of compressed air and recorded depending on time.