ASTM G86-98a(2011)
(Test Method)Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments
Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments
SIGNIFICANCE AND USE
This test method evaluates the relative sensitivity of materials to mechanical impact in ambient pressure liquid oxygen, pressurized liquid oxygen, and pressurized gaseous oxygen.
Any change or variation in test sample configuration, thickness, preparation, or cleanliness may cause a significant change in impact sensitivity/reaction threshold.
Suggested criteria for discontinuing the tests are: (1) occurrence of two reactions in a maximum of 60 samples or less tested at the maximum energy level of 98 J (72 ft•lbf) or one reaction in a maximum of 20 samples tested at any other energy level for a material that fails; (2) no reactions for 20 samples tested at the 98-J (72-ft•lbf) energy level; or (3) a maximum of one reaction in 60 samples tested at the maximum energy level.
SCOPE
1.1 This test method describes test equipment and techniques to determine the impact sensitivity of materials in oxygen under two different conditions: (1) in ambient pressure liquid oxygen (LOX) or (2) under pressure-controlled conditions in LOX or gaseous oxygen (GOX). It is applicable to materials for use in LOX or GOX systems at pressures from ambient to 68.9 MPa (0 to 10 000 psig). The test method described herein addresses testing with pure oxygen environments; however, other oxygen-enriched fluids may be substituted throughout this document.
1.2 This test method provides a means for ranking nonmetallic materials as defined in Guide G63 for use in liquid and gaseous oxygen systems and may not be directly applicable to the determination of the sensitivity of the materials in an end-use configuration. This test method may be used to provide batch-to batch acceptance data. This test method may provide a means for evaluating metallic materials in oxygen-enriched atmospheres also; however, Guide G94 should be consulted for preferred testing methods.
1.3 Values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See also Section 9.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: G86 − 98a (Reapproved 2011)
Standard Test Method for
Determining Ignition Sensitivity of Materials to Mechanical
Impact in Ambient Liquid Oxygen and Pressurized Liquid
and Gaseous Oxygen Environments
ThisstandardisissuedunderthefixeddesignationG86;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2.1 ASTM Standards:
1.1 This test method describes test equipment and tech-
D1193 Specification for Reagent Water
niques to determine the impact sensitivity of materials in
D4080 Specification for Trichloroethylene, Technical and
oxygen under two different conditions: (1) in ambient pressure
Vapor-Degreasing Grade
liquid oxygen (LOX) or (2) under pressure-controlled condi-
G63 Guide for Evaluating Nonmetallic Materials for Oxy-
tions in LOX or gaseous oxygen (GOX). It is applicable to
gen Service
materials for use in LOX or GOX systems at pressures from
G88 Guide for Designing Systems for Oxygen Service
ambient to 68.9 MPa (0 to 10 000 psig). The test method
G93 Practice for Cleaning Methods and Cleanliness Levels
described herein addresses testing with pure oxygen environ-
for Material and Equipment Used in Oxygen-Enriched
ments; however, other oxygen-enriched fluids may be substi-
Environments
tuted throughout this document.
G94 Guide for Evaluating Metals for Oxygen Service
1.2 This test method provides a means for ranking nonme-
2.2 Military Document:
tallic materials as defined in Guide G63 for use in liquid and
MIL-D-16791 Detergent, General Purpose (Liquid, Non-
gaseous oxygen systems and may not be directly applicable to
ionic), Type One
the determination of the sensitivity of the materials in an 5
2.3 American Chemical Society:
end-useconfiguration.Thistestmethodmaybeusedtoprovide
Trichloroethylene, Reagent Grade
batch-to batch acceptance data. This test method may provide 6
2.4 Compressed Gas Association:
a means for evaluating metallic materials in oxygen-enriched
G-4 Oxygen
atmospheresalso;however,GuideG94shouldbeconsultedfor
G-4.1 Cleaning Equipment for Oxygen Service
preferred testing methods.
G-4.3 Oxygen, Gaseous, Type I B
G-4.3 Oxygen, Liquid, Type II B
1.3 Values stated in SI units are to be regarded as the
G-10.1 Nitrogen, Gaseous, Type I B
standard. The values given in parentheses are for information
G-10.1 Nitrogen, Liquid, Type II B
only.
2.5 NASA Standard:
1.4 This standard does not purport to address all of the
NSS 1740.15 Safety Standard for Oxygen and Oxygen
safety concerns, if any, associated with its use. It is the
Systems
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
bility of regulatory limitations prior to use. See also Section 9.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
This test method is under the jurisdiction of ASTM Committee G04 on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
Compatibility and Sensitivity of Materials in Oxygen EnrichedAtmospheres and is dodssp.daps.dla.mil.
the direct responsibility of G04.01 on Test Methods. Available fromAmerican Chemical Society (ACS), 1155 Sixteenth Street, NW
Current edition approved April 1, 2011. Published April 2011. Originally Washington, DC 20036, http://www.acs.org.
approvedin1984.Lastpreviouseditionapprovedin2005asG86 - 98a(2005).DOI: Available from Compressed Gas Association (CGA), 4221 Walney Rd., 5th
10.1520/G0086-98AR11. Floor, Chantilly, VA 20151-2923, http://www.cganet.com.
2 7
NASA Handbook 8060.1B, Pressurized Liquid and Gaseous Oxygen Mechani- AvailablefromNationalAeronauticsandSpaceAdminstration(NASA),NASA
cal Impact Test, Sept. 1981, pp. 4-72. Headquarters, Suite 1M32, Washington, DC 20546.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
G86 − 98a (2011)
2.6 ASTM Adjuncts:
ABMA-Type Impact Tester and Anvil
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 GOX, n—gaseous oxygen.
3.1.2 LOX, n—liquid oxygen.
3.1.3 mechanical impact, n—ablowdeliveredbyaplummet
that has been dropped from a preestablished height onto a
striker pin in contact with a sample.
3.1.4 reaction, n—a chemical change or transformation in
the sample initiated by a mechanical impact.
3.1.4.1 Discussion—A reaction from ambient pressure,
LOX mechanical impact may be determined by an audible
report, an electronically or visually detected flash, obvious
charring of the sample, cup, or striker pin.
3.1.4.2 Discussion—Reactions in pressurized LOX or GOX
are typically indicated by an abrupt increase in test sample
temperature, chamber pressure, and light levels and may be
supplemented by obvious changes in odor, color, or material
appearance as a result of thermal decompositions observed
during examination after the test.
3.1.5 pressure threshold, n—the highest pressure at a given
impact energy level for which the passing criteria have been
met.
3.1.6 energy threshold, n—the highest impact energy level
at a given pressure for which the passing criteria have been
met.
4. Summary of Test Method FIG. 1 Oxygen Impact Test Frame
4.1 The mechanical impact test system is designed to
striker pin, which transmits the energy to the test sample.
expose material samples to mechanical impact in the presence
Observation for any reaction is made and noted. Drop tests are
of liquid or gaseous oxygen at pressures from ambient to 68.9
continued using a fresh sample, sample cup, and striker pin for
MPa (0 to 10 000 psig). The basic drop tower configuration
each drop until the threshold level is determined or the test
consists of: an electromagnet, a plummet, plummet guide
series is completed.
tracks, plummet hold/release mechanism, base plate, anvil
plate, a specimen cup holder, sample cup, and striker pin (see 4.3 For materials tested in pressurized LOX or GOX, each
Fig. 1). For tests conducted under pressure-controlled sample is placed in the test chamber. The test chamber is filled
conditions, the anvil plate and specimen cup holder are with liquid or gaseous oxygen, pressurized to the required test
replaced with a test chamber equipped with a striker pin or pressure, and the striker pin or striker pin counterloader is
striker pin counterloader (see Fig. 2), test chamber purge, pressed down against the top of the test sample. The plummet
pressurization and vent systems (see Fig. 3), and a plummet is dropped from a selected height onto the striker pin or striker
catcher(seeFig.4).Thegeneralprocedureistopreparethetest pincounterloader.Instrumentationdevicesthatmonitorthetest
sample and record significant pretest data. chamber interior for pressure, temperature, and light emission
provide evidence of test sample reaction. The sample is
4.2 Ambient LOX Impact Test—The test conditions (pres-
removed from the chamber, and the sample is inspected for
sure and temperature) are the ambient pressure of the test
other evidence of reaction such as odor or charring. Drop tests
facility and the boiling point of LOX at that pressure. Each
are continued using a fresh sample, sample holder, and striker
sample is placed into a specimen cup (see Fig. 5), precooled in
pin or striker pin counterloader for each drop, until the
a sample freezing box (Fig. 6), covered with LOX, and placed
threshold level is determined or the test series is completed.
in the cup holder seater in the anvil assembly of the impact
Additional modifications to the above procedure are required
tester. The plummet is dropped from a selected height onto the
when testing is performed at temperatures above ambient.
4.4 This test method may be used to determine the impact
Detailed drawings from the ABMA-Type Impact Tester and Anvil Region
sensitivity of a material, batch-to-batch acceptance, or to
Assembly are available at a nominal fee fromASTM International, 100 Barr Harbor
Dr., Philadelphia, PA 19428. Request Adjunct ADJD2512. satisfy other prescribed pass-fail criteria.
G86 − 98a (2011)
1 Pneumatic Amplifier Chamber 9 High-Pressure Chamber
2 Equalizer Pin Anvil 10 Sample Cup
3 Equalizer Pin 11 Anvil Nut
4 Pneumatic Amplifier Diaphragm 12 High-Pressure Seal
5 Pneumatic Amplifier Chamber GN 13 Pressurization Port
Cavity 14 Vent Port
6 and 8 Striker Pin 15 Sightglass for Photocell
7 High-Pressure Seal
FIG. 2 Two Types of High-Pressure Test Chambers
5. Significance and Use 5.3 Suggested criteria for discontinuing the tests are: (1)
occurrence of two reactions in a maximum of 60 samples or
5.1 This test method evaluates the relative sensitivity of
less tested at the maximum energy level of 98 J (72 ft•lbf) or
materials to mechanical impact in ambient pressure liquid
one reaction in a maximum of 20 samples tested at any other
oxygen, pressurized liquid oxygen, and pressurized gaseous
energy level for a material that fails; (2) no reactions for 20
oxygen.
samples tested at the 98-J (72-ft•lbf) energy level; or (3) a
5.2 Any change or variation in test sample configuration,
maximumofonereactionin60samplestestedatthemaximum
thickness, preparation, or cleanliness may cause a significant
energy level.
change in impact sensitivity/reaction threshold.
G86 − 98a (2011)
FIG. 3 Typical Pressurization Piping system for a LOX/GOX Pressurized Test System
NOTE 1—Break sharp edges 0.4 mm.
NOTE 2—The cup is formed by deep drawing.
NOTE 3—The thickness and parallelness of the cup bottom shall be
FIG. 4 Typical Plummet Rebound Limiter Assembly
controlled to 2.0 mm by coining.
NOTE 4—Material: any 3000 or 5000 series aluminum alloy.
FIG. 5 LOX Impact Tester One-Piece Sample Cup
6. Criteria for Acceptance for Ambient LOX and
Pressurized LOX and GOX Mechanical Impact Test 6.2 The test may be discontinued and the materials consid-
ered to have failed if there is one reaction in 20 drops at any
6.1 To meet the requirements for acceptability, the material
energy level less than 98 J (72 ft•lbf).
shall show no reaction when being subjected to 20 successive
impact tests tested at 98 J (72 ft•lbf) using the equipment 6.3 Amaterial is acceptable after 60 successive impact tests
described in Section 10. withnotmorethanonereactionat98J(72ft•lbf).Thetestmay
G86 − 98a (2011)
7. Sample Preparation
7.1 The material to be tested must be traceable back to the
original manufacturer and to specific batch or lot numbers, or
to both. When received, the test material must be accompanied
by proper identification, for example, product data sheets,
batch or lot numbers identifying the sample, material
manufacturer, and appropriate material safety data sheets. The
material must be inspected to ensure that it is at the worst-case
use thickness and any flaws shall be noted. Preparation of
samples for testing involve the following tasks: (1) receiving
and visually inspecting the material, (2) preparing samples to
the proper dimensions, (3) cleaning the samples, and (4)
inspecting the samples.
7.1.1 Sufficient material shall be available to permit prepa-
ration and testing of 140 separate 17.5-mm ( ⁄16-in.) diameter
disk samples. Sheet materials up to 6.3-mm ( ⁄4-in.) in thick-
ness shall be tested as 17.5 mm ( ⁄16-in.) diameter disks in the
FIG. 6 Typical Sample Freezing Box
thickness intended for use (see Table 1).
7.1.2 Materials normally used in thicknesses greater than
6.35 mm ( ⁄4 in.) shall be sized and tested as 17.5-mm diameter
be terminated and the material considered to have failed if
disks of 6.35- 6 0.13-mm (0.250- 6 0.006-in.) thickness.
there are two reactions in 60 tests or less at 98 J (72 ft•lbf).
Failure of samples to meet the requirements of this test method
6.4 The material shall show none of the following reactions
shall be cause for the rejection of the material. Greases, fluids,
during any of the tests.
and other materials, whose thicknesses are directed by condi-
6.4.1 Audible explosion.
tions of use, shall be tested as 1.27- 6 0.13-mm (0.050- 6
6.4.2 Flash (electronically or visually detected).
0.005-in.) layers in special test cups. Materials not readily
6.4.3 Evidence of burning (obvious charring, see Note 1).
available in sheet form shall be tested in the available configu-
6.4.4 Major discoloration (as a result of ignition only rather
ration. Specimens shall be free of ragged edges, fins, or other
than other phenomena).
irregularities.
6.4.5 A temperature or pressure spike in elevated tempera-
7.2 Liquid Samples—Prepare a homogeneous sample. A
ture tests.
microburette may be used to transfer the sample into special
NOTE 1—A burnt odor alone is not considered sufficient proof that a sample cups 1.27 6 0.13 mm (0.050 6 0.005 in.) deep (see
reaction has occurred. If a reaction occurs (including those during bounce
Fig. 7). For highly viscous materials, a microsyringe may be
of plummet), it shall be reported as evidence of sensitivity. Inclusion of
used. Determine the volume of the sample required to obtain a
bounce reactions applies to ambient LOX mechanical impact tests only.
sample thickness of 1.27 6 0.13 mm (0.050 6 0.005 in.) in the
6.5 All materials that fail 6.1 criteria and remain candidates
sample cup. This determination is required due to variations in
for use must be subjected to LOX or GOX mechanical impact
such physical properties as density, surface tension, and
energy threshold determinations in the thickness of use.
volatility from liquid to liquid.Amicrometre depth gauge with
leveling blocks is suggested for measurement. The work table
6.6 The material to be tested must be traceable back to the
must be level. Test material should be loaded into the sample
original manufacturer and to a specific batch or lot numbers, or
cup just before loading the cup into the test chamber (or
both.
freezing box, if testing in liquid oxygen).
6.7 The thickness of the sample shall be the worst-case
7.3 Leak Check Compounds, Dye, Dye Penetrant, and
thickness. While the worst-case thickness has been found to
Emulsifier, Method 1—Clean, unsealed, sulfuric acid-anodized
vary from material to material, the general trend has been that
6061-T6aluminumalloydisks(oranyothersubstratespecified
thinner samples of materials are gener
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.