iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E2252-04

(Practice)

Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities

Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities

SIGNIFICANCE AND USE
This practice outlines lead hazard reduction methods that have been shown to be effective in preventing lead poisoning in children.
This practice tabulates advantages, disadvantages, and relative costs of the reduction methods to assist professionals such as certified lead risk assessors, supervisors, or project designers in selecting appropriate cost-effective options for controlling lead hazards identified during a lead risk assessment. Different control methods may be equally effective in controlling a given lead hazard and, consequently, the selection of a specific control method may depend on the needs and economic constraints of the client or building owner.
This practice is intended to complement other lead hazard activities that are performed in accordance with regulations promulgated by authorities having jurisdiction. For example, in some jurisdictions, a lead hazard risk assessment, by regulation, consists of a visual assessment, a hazard assessment including environmental monitoring for lead, and selection of lead hazard reduction methods.
This practice is intended to assist homeowners, owners and occupants of rental property, lenders, insurers, and others who have interest in selecting options for controlling hazards associated with leaded paint, dust, or soil.
This practice complements Practice E 2115. Information and data gathered in accordance with Practice E 2115 and this practice are used in preparing a risk assessment report. Subsequent lead hazards are mitigated through implementation of controls selected in accordance with this present practice.
This practice addresses the most commonly used lead hazard reduction methods. It is left to users of this practice to identify the advantages, disadvantages, and relative costs associated with emerging control technologies for comparison with these characteristics of established lead hazard control methods.
This practice does not address specific historic preservation requirements. The interi...
SCOPE
1.1 This practice describes the selection of lead hazard reduction methods for controlling lead hazard risks identified during risk assessments of residential dwellings and child occupied facilities.
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This practice contains notes, which are explanatory and are not part of the mandatory requirements of this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Mar-2004
ICS
91.120.01 - Protection of and in buildings in general
Technical Committee
E06 - Performance of Buildings
Current Stage
Ref Project

Relations

Replaces
ASTM E2252-03 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
Effective Date
01-Apr-2004
Replaced By
ASTM E2252-12 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
Effective Date
01-Apr-2012
Referred By
ASTM E2115-22 - Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities
Effective Date
01-Apr-2004

Buy Standard

ASTM E2252-04 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied FacilitiesASTM E2252-04 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
PreviousNext
Standard
ASTM E2252-04 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E2252 – 04
Standard Practice for
Selection of Lead Hazard Reduction Methods for Identified
1
Risks in Residential Housing or Child Occupied Facilities
This standard is issued under the fixed designation E2252; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E2239 Practice for Record Keeping and Record Preserva-
tion for Lead Hazard Activities
1.1 This practice describes the selection of lead hazard
4
2.2 HUD:
reduction methods for controlling lead hazard risks identified
Guidelines for the Evaluation and Control of Lead-Based
during risk assessments of residential dwellings and child
Paint Hazards in Housing
occupied facilities.
24 CFR Part 35 Requirements for Notification, Evaluation
1.2 The values stated in SI units are to be regarded as the
and Reduction of Lead-Based Paint Hazards in Federally
standard.
Owned Residential Property, and Housing Receiving Fed-
1.3 This practice contains notes, which are explanatory and
eral Assistance; Final Rule, September 15, 1999
are not part of the mandatory requirements of this standard.
5
2.3 EPA:
1.4 This standard does not purport to address all of the
Protect Your Family from Lead in Your Home
safety concerns, if any, associated with its use. It is the
40 CFR Part 745, Subpart L, Lead-Based Paint Activities
responsibility of the user of this standard to establish appro-
6
2.4 NIBS:
priate safety and health practices and determine the applica-
Lead-Based Paint: Operations and Maintenance Work Prac-
bility of regulatory limitations prior to use.
tices Manual for Homes and Buildings
2. Referenced Documents Guide Specifications for Reducing Lead-Based Paint Haz-
2
ards
2.1 ASTM Standards:
7
2.5 R.S. Means:
E917 Practice for Measuring Life-Cycle Costs of Buildings
Building Construction Cost Data
and Building Systems
E1605 Terminology Relating to Lead in Buildings
3. Terminology
E1795 Specification for Non-Reinforced Liquid Coating
3.1 Definitions—For definitions of terms used in this prac-
Encapsulation Products for Leaded Paint in Buildings
tice refer to Terminology E1605.
E1796 Guide for Selection and Use of Liquid Coating
Encapsulation Products for Leaded Paint in Buildings
4. Significance and Use
E1797 Specification for Reinforced Liquid Coating Encap-
4.1 This practice outlines lead hazard reduction methods
sulation Products for Leaded Paint in Buildings
that have been shown to be effective in preventing lead
E2052 Guide for Evaluation, Management, and Control of
3 poisoning in children.
Lead Hazards in Facilities
4.2 This practice tabulates advantages, disadvantages, and
E2115 Guide for Conducting Lead Hazard Assessments of
relative costs of the reduction methods to assist professionals
Dwellings and of Other Child-Occupied Facilities
such as certified lead risk assessors, supervisors, or project
designers in selecting appropriate cost-effective options for
1
This practice is under the jurisdiction of ASTM Committee E06 on Perfor-
controlling lead hazards identified during a lead risk assess-
manceofBuildingsandisthedirectresponsibilityofSubcommitteeE06.23onLead
ment. Different control methods may be equally effective in
Hazards Associated With Buildings.
controllingagivenleadhazardand,consequently,theselection
Current edition approved April 1, 2004. Published April 2004. Originally
approved in 2002. Last previous edition approved in 2003 as E2252 – 03. DOI:
10.1520/E2252-04.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or U.S. Department of Housing and Urban Development, Washington DC 20140,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Current Edition. http://www.hud.gov/offices/lead/
5
Standards volume information, refer to the standard’s Document Summary page on Environmental ProtectionAgency, Washington DC, 1999. http://www.epa.gov/
6
the ASTM website. National Institute of Building Sciences, Washington DC May 1995. http://
3
Withdrawn. The last approved version of this historical standard is referenced www.nibs.org/
7
on www.astm.org. 1998. http://www.rsmeans.com/
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E2252 – 04
of a specific control method may depend on the needs and 6. Lead Hazard Reduction Methods
economic constraints of the client or building owner.
6.1 General—There are two approaches to reducing lead
4.3 This practice is intended to complement other lead
hazards: interim control and abatement. Most often, a combi-
hazard activities that are
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2131-16(2022)(Practice)
Standard Practice for Addressing and Reporting Losses of Tangible Property

SIGNIFICANCE AND USE
5.1 Losses of property are indicators of the effectiveness of operations. Excessive losses can indicate poor internal management and controls, policy or procedural weaknesses, or lack of compliance, any one of which can have a negative impact on profitability, mission, performance, or reputation.  
5.2 Addressing and reporting losses provides indicators of needed potential action by decision makers.  
5.3 Though the term equipment is used consistently throughout this practice, this process may be used for the other classes of property, for example, raw material in inventory.  
5.4 This practice does not change any requirements that may be imposed through law, regulations, contract terms, and conditions.
Note 1: When this practice is submitted in response to a contract solicitation and evaluated as part of a contract award process, this practice may be deemed a representation.
SCOPE
1.1 This practice focuses on addressing and reporting losses of tangible property.  
1.2 Loss occurrences are key aspects of risk management. Projecting the possibility or probability of losses, discovering, disclosing, reporting, managing, and minimizing losses to a reasonable extent is a critical economic factor in the success of the owning or holding entity. This practice also establishes acceptable levels of losses.  
1.3 Losses are often discovered as a result of an occurrence, a physical inventory, property custodian or entity self-assessment, or external audit. An actual loss occurrence can be at any time during the property life cycle.  
1.4 Assessing and determining financial liability for losses is not addressed in this practice; such assessments are generally subject to individual contracts or other arrangements.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2252-22(Practice)
Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities

SIGNIFICANCE AND USE
4.1 This practice outlines lead hazard reduction methods that have been shown to be effective in preventing lead poisoning in children.  
4.2 This practice tabulates advantages, disadvantages, and relative costs of the reduction methods to assist professionals such as certified lead-based paint risk assessors, supervisors, or project designers in selecting appropriate cost-effective options for controlling lead hazards identified during a lead risk assessment. Different control methods may be equally effective in controlling a given lead hazard and, consequently, the selection of a specific control method may depend on the needs and economic constraints of the client or building owner.  
4.3 This practice is intended to complement other lead hazard activities that are performed in accordance with regulations promulgated by authorities having jurisdiction. For example, in some jurisdictions, a lead hazard risk assessment, by regulation, consists of a visual assessment, a hazard assessment including environmental monitoring for lead, and selection of lead hazard reduction methods.  
4.4 This practice is intended to assist homeowners, owners and occupants of rental property, lenders, insurers, and others who have interest in selecting options for controlling lead hazards associated with leaded paint, dust, or soil.  
4.5 This practice complements Guide E2115. Information and data gathered in accordance with Guide E2115 and this practice are used in preparing a risk assessment report. Subsequent lead hazards are mitigated through implementation of controls selected in accordance with this present practice.  
4.6 This practice addresses the most commonly used lead hazard reduction methods. It is left to users of this practice to identify the advantages, disadvantages, and relative costs associated with emerging control technologies for comparison with these characteristics of established lead hazard control methods.  
4.7 This practice does not address specific his...
SCOPE
1.1 This practice describes the selection of lead hazard reduction methods for controlling lead hazard risks identified during risk assessments of residential dwellings and child occupied facilities.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.3 This practice contains notes, which are explanatory and are not part of the mandatory requirements of this standard.  
1.4 Methods described in this practice may not meet or be allowed by requirements or regulations established by local authorities having jurisdiction. It is the responsibility of the user of this standard to comply with all such requirements and regulations.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM F1637-21(Practice)
Standard Practice for Safe Walking Surfaces

SIGNIFICANCE AND USE
4.1 This practice addresses elements along and in walkways including floors and walkway surfaces, sidewalks, short flight stairs, gratings, wheel stops, and speed bumps. Swimming pools, bath tubs, showers, natural walks, and unimproved paths are beyond the scope of this practice.
SCOPE
1.1 This practice covers design and construction guidelines and minimum maintenance criteria for new and existing buildings and structures. This practice is intended to provide reasonably safe walking surfaces for pedestrians wearing ordinary footwear. These guidelines may not be adequate for those with certain mobility impairments.  
1.2 Conformance with this practice will not alleviate all hazards; however, conformance will reduce certain pedestrian risks.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E2239-20(Practice)
Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities

SIGNIFICANCE AND USE
4.1 This practice is intended to help reduce risks associated with lead hazards in buildings by providing standardized requirements for preserving records, findings, and recommendations associated with lead hazard activities.  
4.2 This practice is intended for use by individuals and organizations that develop and have need to preserve objective evidence when contracting for or when conducting lead hazard activities themselves.  
4.2.1 This practice is intended to assist in complying with management system requirements for record keeping promulgated by authorities having jurisdiction regarding conduct of lead hazard activities.
SCOPE
1.1 This practice describes requirements for preservation of records generated during lead hazard activities.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off