iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D7022-04e1

(Terminology)

Standard Terminology Relating to Apparel (Withdrawn 2013)

Standard Terminology Relating to Apparel (Withdrawn 2013)

SCOPE
1.1 This standard is the compilation of all terminology developed by Subcommittee D13.61 on Apparel.
1.2 This terminology is unique to the Apparel industry. Meanings of the same terms used outside the industry can be found in other compilations or in dictionaries of general usage.
1.3 In addition to being a specialized dictionary, D7022 is also useful for managing the Subcommittee's terminology.
1.4 Terms listed are under the jurisdiction of Subcommittee D13.61.
1.5 For definitions of other textile terms see Terminology D123.
WITHDRAWN RATIONALE
This standard is the compilation of all terminology developed by Subcommittee D13.61 on Apparel.
Formerly under the jurisdiction of Committee D13 on Textiles and the direct responsibility of Subcommittee D13.61 on Apparel, this terminology was withdrawn in February 2013 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Historical
Publication Date
31-May-2004
Withdrawal Date
18-Feb-2013
ICS
01.040.61 - Clothing industry (Vocabularies)
61.020 - Clothes
Technical Committee
D13 - Textiles
Drafting Committee
D13.61 - Apparel
Current Stage
Ref Project

Relations

Replaces
ASTM D7022-04 - Standard Terminology Relating to Apparel
Effective Date
01-Jun-2004
Replaced By
ASTM D7022-13 - Standard Terminology Relating to Apparel
Effective Date
01-Oct-2013
Referred By
ASTM D4154-22 - Standard Performance Specification for Men's and Boys' Knitted and Woven Beachwear and Sports Shirt Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D7017-20 - Standard Performance Specification for Water-Resistant Rainwear and All-Purpose, Water-Repellent Coat Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D3780-22 - Standard Performance Specification for Men's and Boys' Woven Dress Suit Fabrics and Woven Sportswear Jacket, Slack, and Trouser Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D7507-23 - Standard Specification for Woven High Stretch Fabrics Used in Apparel
Effective Date
01-Jun-2004
Referred By
ASTM D4235-20 - Standard Performance Specification for Women's and Girls' Knitted Blouse and Dress Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D4035-22 - Standard Performance Specification for Knitted Necktie and Scarf Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D3996-23 - Standard Performance Specification for Knit Swimwear Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D4118-23 - Standard Performance Specification for Woven Coverall, Dungaree, Overall, and Shop-Coat Fabrics
Effective Date
01-Jun-2004
Referred By
ASTM D3995-23 - Standard Performance Specification for Knitted Career Apparel Fabrics: Dress and Vocational
Effective Date
01-Jun-2004
Referred By
ASTM D6321/D6321M-22 - Standard Practice for the Evaluation of Machine Washable T-Shirts
Effective Date
01-Jun-2004
Referred By
ASTM D4231-22 - Standard Practice for Evaluation of Launderable Woven Dress Shirts and Sports Shirts
Effective Date
01-Jun-2004
Referred By
ASTM D3181-15(2019) - Standard Guide for Conducting Wear Tests on Textiles
Effective Date
01-Jun-2004
Referred By
ASTM D7019-20 - Standard Performance Specification for Brassiere, Slip, Lingerie and Underwear Fabrics
Effective Date
01-Jun-2004

Buy Standard

ASTM D7022-04e1 - Standard Terminology Relating to Apparel (Withdrawn 2013)ASTM D7022-04e1 - Standard Terminology Relating to Apparel (Withdrawn 2013)
PreviousNext
Standard
ASTM D7022-04e1 - Standard Terminology Relating to Apparel (Withdrawn 2013)
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D7022 − 04
StandardTerminology Relating to
1
Apparel
This standard is issued under the fixed designation D7022; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Terms from D3135, D7017 and D7268 were added editorially in May 2012.
1. Scope ven Dress Suit Fabrics and Woven Sportswear Jacket,
Slack, and Trouser Fabrics
1.1 This standard is the compilation of all terminology
D3781 Performance Specification for Men’s and Boys’Knit-
developed by Subcommittee D13.61 on Apparel.
ted Rainwear andAll-Purpose, Water-Repellent Coat Fab-
1.2 This terminology is unique to the Apparel industry.
3
rics (Withdrawn 2005)
Meanings of the same terms used outside the industry can be
D3782 Performance Specification for Men’s and Boys’Knit-
found in other compilations or in dictionaries of general usage.
ted Dress Suit Fabrics and Knitted Sportswear Jacket,
1.3 In addition to being a specialized dictionary, D7022 is
Slack, and Trouser Fabrics
also useful for managing the Subcommittee’s terminology.
D3783 Performance Specification for Woven Flat Lining
3
1.4 Terms listed are under the jurisdiction of Subcommittee Fabrics for Men’s and Boys’Apparel (Withdrawn 2011)
D13.61.
D3819 Performance Specification for Men’s and Boys’Wo-
3
ven Pajama Fabrics (Withdrawn 2005)
1.5 For definitions of other textile terms see Terminology
D3820 Performance Specification for Men’s and Boys’Wo-
D123.
3
ven Underwear Fabrics (Withdrawn 2005)
2. Referenced Documents
D3887 Specification for Tolerances for Knitted Fabrics
2
D3994 Performance Specification for Woven Swimwear
2.1 ASTM Standards:
Fabrics
D3135 Specification for Performance of Bonded, Fused, and
D3995 Performance Specification for Men’s and Women’s
Laminated Apparel Fabrics
Knitted Career Apparel Fabrics: Dress and Vocational
D3477 Performance Specification for Men’s and Boys’Wo-
3
D3996 Performance Specification for Knit Swimwear Fab-
ven Dress Shirt Fabrics (Withdrawn 2005)
rics
D3562 Performance Specification for Woven Drycleanable
Coat Fabrics D4035 Performance Specification for Knitted Necktie and
D3655 Performance Specification for Men’s and Women’s Scarf Fabrics
Sliver Knitted Overcoat and Jacket Fabrics
D4038 Performance Specification for Women’s and Girls’
3
D3691 PerformanceSpecificationforWoven,Lace,andKnit
Woven Dress and Blouse Fabrics (Withdrawn 2004)
Household Curtain and Drapery Fabrics
D4109 Performance Specification for Men’s and Boys’Wo-
D3778 Specification for Women’s and Girls’ Drycleanable
ven Coverall, Dungaree, Overall, and Shop-Coat Fabrics
3
3
Woven Dress Coat Fabrics (Withdrawn 1999)
(Withdrawn 2011)
D3779 Performance Specification for Women’s and Girls’
D4115 Performance Specification for Women’s and Girls’
Woven Rainwear and All-Purpose, Water-Repellent Coat
Knitted and Woven Dress Glove Fabrics
3
Fabrics (Withdrawn 2005)
D4117 Performance Specification for Women’s and Girls’
D3780 Performance Specification for Men’s and Boys’Wo-
Woven Robe, Negligee, Nightgown, Pajama, Slip, and
3
Lingerie Fabrics (Withdrawn 2005)
1 D4118 Performance Specification for Women’s Woven
ThisterminologyisunderthejurisdictionofASTMCommitteeD13onTextiles
and is the direct responsibility of Subcommittee D13.61 on Apparel.
Coverall, Dungaree, Overall, and Shop Coat Fabrics
Current edition approved June 1, 2004. Published July 2004. DOI: 10.1520/
D4119 Performance Specification for Men’s and Boys’Knit-
D7022-04E01.
2 ted Dress Shirt Fabrics
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D4154 Performance Specification for Men’s and Boys’Knit-
Standards volume information, refer to the standard’s Document Summary page on
ted and Woven Beachwear and Sports Shirt Fabrics
the ASTM website.
3 D4156 Performance Specification for Women’s and Girls’
The last approved version of this historical standard is referenced on
www.astm.org. Knitted Sportswear Fabrics
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
D7022 − 04
D4231 Practice for Evaluation of Launderable Woven Dress career apparel, n—garments, the styling and performance of
Shirts and Sports Shirts which are designed for various end uses so as to be suitable
D4232 Performance Specification for Men’s and Women’s for on-the-job wear in a variety of businesses and profes-
Dress and Vocational Career Apparel Fabrics sions.(Seealso dress career appareland vocational career
D4234 Performance Specification for Women
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5219-15(Terminology)
Standard Terminology Relating to Body Dimensions for Apparel Sizing

SCOPE
1.1 This standard is a compilation of terminology related to the body dimensions for apparel sizing.  
1.2 For definitions of other textile terms, refer to Terminology D123.  
1.3 The terms are listed in alphabetical order regardless of whether they are horizontal or vertical measurements. The three dimensional Avatars were created by Alvanon Inc. See Figs. 1-19.  
1.4 The term “height” has been designated for vertical measurements.  
1.5 The term “length” has been designated for contour measurements.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F1646-16(Terminology)
Standard Terminology Relating to Walkway Safety and Footwear

SCOPE
1.1 The terminology standard covers terminology related to walkway safety and footwear.  
1.2 Words adequately defined in standard dictionaries are not included. Included are words that are particular to this industry and those contained in standards under the jurisdiction of ASTM Committee F13 on Pedestrian/Walkway Safety and Footwear.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5219-15(Terminology)
Standard Terminology Relating to Body Dimensions for Apparel Sizing

SCOPE
1.1 This standard is a compilation of terminology related to the body dimensions for apparel sizing.  
1.2 For definitions of other textile terms, refer to Terminology D123.  
1.3 The terms are listed in alphabetical order regardless of whether they are horizontal or vertical measurements. The three dimensional Avatars were created by Alvanon Inc. See Figs. 1-19.  
1.4 The term “height” has been designated for vertical measurements.  
1.5 The term “length” has been designated for contour measurements.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off