ASTM D3679-21
(Specification)Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
ABSTRACT
This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and windload resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. The siding shall be made of one or more layers of poly(vinyl chloride) (PVC) compound. Any layers of materials other than poly (vinyl chloride) (PVC) compound shall be kept to less than 20% by volume. The PVC compound when extruded into siding shall maintain uniform color and be free of any visual surface or structural changes, such as peeling, chipping, cracking, flaking, or pitting. The PVC compound shall be compounded so as to provide the heat stability and weather exposure stability required for the siding market application. PVC siding shall not contain elemental lead (Pb) or compounds of that material other than traces incidental to raw materials or the manufacturing process. This limitation applies to both PVC substrate and to any cap or film material. Materials shall be tested and the individual grades shall conform to specified values of length and width, thickness, camber, heat shrinkage, impact resistance, coefficient of linear expansion, gloss, surface distortion, color, weathering, windload resistance, and nail slot allowance for thermal expansion.
SCOPE
1.1 This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC compound. Methods of indicating compliance with this specification are also provided.
1.2 The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3 Rigid (unplasticized) PVC soffit is covered in Specification D4477.
1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.
Note 1: Information with regard to siding maintenance shall be obtained from the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 2: There is no known ISO equivalent to this standard.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3679 −21 An American National Standard
Standard Specification for
1
Rigid Poly(Vinyl Chloride) (PVC) Siding
This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification establishes requirements and test 2.1 ASTM Standards:
methodsforthematerials,dimensions,warp,shrinkage,impact D618Practice for Conditioning Plastics for Testing
strength, expansion, appearance, and wind load resistance of D635Test Method for Rate of Burning and/or Extent and
extruded single-wall siding manufactured from rigid (unplas- Time of Burning of Plastics in a Horizontal Position
ticized) PVC compound. Methods of indicating compliance D696TestMethodforCoefficientofLinearThermalExpan-
with this specification are also provided. sion of Plastics Between −30°C and 30°C with aVitreous
Silica Dilatometer
1.2 The use PVC recycled plastic in this product shall be in
D883Terminology Relating to Plastics
accordance with the requirements in Section 4.
D1042Test Method for Linear Dimensional Changes of
1.3 Rigid (unplasticized) PVC soffit is covered in Specifi-
Plastics Caused by Exposure to Heat and Moisture
cation D4477.
D1435Practice for Outdoor Weathering of Plastics
1.4 Sidingproducedtothisspecificationshallbeinstalledin D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
accordancewithPracticeD4756.Referenceshallalsobemade
to the manufacturer’s installation instructions for the specific D2244Practice for Calculation of Color Tolerances and
Color Differences from Instrumentally Measured Color
product to be installed.
Coordinates
NOTE 1—Information with regard to siding maintenance shall be
D2457Test Method for Specular Gloss of Plastic Films and
obtained from the manufacturer.
Solid Plastics
1.5 Thevaluesstatedininch-poundunitsaretoberegarded
D3892Practice for Packaging/Packing of Plastics
as standard. The values given in parentheses are mathematical
D4226Test Methods for Impact Resistance of Rigid Poly-
conversions to SI units that are provided for information only
(Vinyl Chloride) (PVC) Building Products
and are not considered standard.
D4477Specification for Rigid (Unplasticized) Poly(Vinyl
1.6 The following precautionary caveat pertains to the test
Chloride) (PVC) Soffit
method portion only, Section 6, of this specification: This
D4756Practice for Installation of Rigid Poly(Vinyl Chlo-
standard does not purport to address all of the safety concerns,
ride) (PVC) Siding and Soffit
if any, associated with its use. It is the responsibility of the user
D5033GuideforDevelopmentofASTMStandardsRelating
of this standard to establish appropriate safety, health, and
to Recycling and Use of Recycled Plastics (Withdrawn
3
environmental practices and determine the applicability of
2007)
regulatory limitations prior to use.
D5206Test Method for Windload Resistance of Rigid Plas-
tic Siding
NOTE 2—There is no known ISO equivalent to this standard.
D5947Test Methods for Physical Dimensions of Solid
1.7 This international standard was developed in accor-
Plastics Specimens
dance with internationally recognized principles on standard-
E631Terminology of Building Constructions
ization established in the Decision on Principles for the
E1753Practice for Use of Qualitative Chemical Spot Test
Development of International Standards, Guides and Recom-
Kits for Detection of Lead in Dry Paint Films
mendations issued by the World Trade Organization Technical
G147Practice for Conditioning and Handling of Nonmetal-
Barriers to Trade (TBT) Committee.
lic Materials for Natural and Artificial Weathering Tests
1 2
This specification is under the jurisdiction of ASTM Committee D20 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
PlasticsandisthedirectresponsibilityofSubcommitteeD20.24onPlasticBuilding contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Products. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2021. Published September 2021. Originally the ASTM website.
3
approved in 1979. Last previous edition approved in 2017 as D3679–17. DOI: The last approved version of this historical standard is referenced on
10.1520/D3679-21. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoho
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3679 − 17 D3679 − 21 An American National Standard
Standard Specification for
1
Rigid Poly(Vinyl Chloride) (PVC) Siding
This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes requirements and test methods for the materials, dimensions, warp, shrinkage, impact strength,
expansion, appearance, and wind load resistance of extruded single-wall siding manufactured from rigid (unplasticized) PVC
compound. Methods of indicating compliance with this specification are also provided.
1.2 The use PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.
1.3 Rigid (unplasticized) PVC soffit is covered in Specification D4477.
1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to
the manufacturer’s installation instructions for the specific product to be installed.
NOTE 1—Information with regard to siding maintenance shall be obtained from the manufacturer.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
NOTE 2—There is no known ISO equivalent to this standard.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.
Current edition approved June 1, 2017Sept. 1, 2021. Published July 2017September 2021. Originally approved in 1979. Last previous edition approved in 20132017 as
D3679 – 13.D3679 – 17. DOI: 10.1520/D3679-17.10.1520/D3679-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3679 − 21
D696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica
Dilatometer
D883 Terminology Relating to Plastics
D1042 Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and Moisture
D1435 Practice for Outdoor Weathering of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
D2457 Test Method for Specular Gloss of Plastic Films and Solid Plastics
D3892 Practice for Packaging/Packing of Plastics
D4226 Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building Products
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
D4756 Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
3
D5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics (Withdrawn 2007)
D5206 Test Method for Windload Resistance of Rigid Plastic Siding
D5947 Test Methods for Physical Dimensions of
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3679 − 21 An American National Standard
Standard Specification for
1
Rigid Poly(Vinyl Chloride) (PVC) Siding
This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification establishes requirements and test 2.1 ASTM Standards:
methods for the materials, dimensions, warp, shrinkage, impact D618 Practice for Conditioning Plastics for Testing
strength, expansion, appearance, and wind load resistance of D635 Test Method for Rate of Burning and/or Extent and
extruded single-wall siding manufactured from rigid (unplas- Time of Burning of Plastics in a Horizontal Position
ticized) PVC compound. Methods of indicating compliance D696 Test Method for Coefficient of Linear Thermal Expan-
with this specification are also provided. sion of Plastics Between −30°C and 30°C with a Vitreous
Silica Dilatometer
1.2 The use PVC recycled plastic in this product shall be in
D883 Terminology Relating to Plastics
accordance with the requirements in Section 4.
D1042 Test Method for Linear Dimensional Changes of
1.3 Rigid (unplasticized) PVC soffit is covered in Specifi-
Plastics Caused by Exposure to Heat and Moisture
cation D4477.
D1435 Practice for Outdoor Weathering of Plastics
D1600 Terminology for Abbreviated Terms Relating to Plas-
1.4 Siding produced to this specification shall be installed in
accordance with Practice D4756. Reference shall also be made tics
D2244 Practice for Calculation of Color Tolerances and
to the manufacturer’s installation instructions for the specific
product to be installed. Color Differences from Instrumentally Measured Color
Coordinates
NOTE 1—Information with regard to siding maintenance shall be
D2457 Test Method for Specular Gloss of Plastic Films and
obtained from the manufacturer.
Solid Plastics
1.5 The values stated in inch-pound units are to be regarded
D3892 Practice for Packaging/Packing of Plastics
as standard. The values given in parentheses are mathematical
D4226 Test Methods for Impact Resistance of Rigid Poly-
conversions to SI units that are provided for information only
(Vinyl Chloride) (PVC) Building Products
and are not considered standard.
D4477 Specification for Rigid (Unplasticized) Poly(Vinyl
1.6 The following precautionary caveat pertains to the test
Chloride) (PVC) Soffit
method portion only, Section 6, of this specification: This
D4756 Practice for Installation of Rigid Poly(Vinyl Chlo-
standard does not purport to address all of the safety concerns,
ride) (PVC) Siding and Soffit
if any, associated with its use. It is the responsibility of the user
D5033 Guide for Development of ASTM Standards Relating
of this standard to establish appropriate safety, health, and
to Recycling and Use of Recycled Plastics (Withdrawn
3
environmental practices and determine the applicability of
2007)
regulatory limitations prior to use.
D5206 Test Method for Windload Resistance of Rigid Plas-
tic Siding
NOTE 2—There is no known ISO equivalent to this standard.
D5947 Test Methods for Physical Dimensions of Solid
1.7 This international standard was developed in accor-
Plastics Specimens
dance with internationally recognized principles on standard-
E631 Terminology of Building Constructions
ization established in the Decision on Principles for the
E1753 Practice for Use of Qualitative Chemical Spot Test
Development of International Standards, Guides and Recom-
Kits for Detection of Lead in Dry Paint Films
mendations issued by the World Trade Organization Technical
G147 Practice for Conditioning and Handling of Nonmetal-
Barriers to Trade (TBT) Committee.
lic Materials for Natural and Artificial Weathering Tests
1 2
This specification is under the jurisdiction of ASTM Committee D20 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Products. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2021. Published September 2021. Originally the ASTM website.
3
approved in 1979. Last previous edition approved in 2017 as D3679 – 17. DOI: The last approved version of this historical standard is referenced on
10.1520/D3679-21. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.