ASTM A439-83(2009)
(Specification)Standard Specification for Austenitic Ductile Iron Castings
Standard Specification for Austenitic Ductile Iron Castings
ABSTRACT
This specification covers austenitic ductile iron castings used for their resistance to heat, corrosion and wear. The castings shall be melt processed using cupolas, air furnaces, electric furnaces or crucible furnaces. The iron castings shall undergo magnetic permeability test. Samples taken from test coupons, broken test specimens, or castings shall conform to the required chemical compositions of carbon, silicon, manganese, phosphorus, nickel and chromium. Mechanical tests shall be performed wherein the iron casting specimens shall conform to the required values of tensile strength, yield strength, elongation and Brinell hardness.
SCOPE
1.1 This specification covers austenitic ductile iron castings, which are used primarily for their resistance to heat, corrosion, and wear, and for other special purposes.
1.2 Austenitic ductile iron, also known as austenitic nodular iron or austenitic spheroidal iron, is characterized by having its graphite substantially in a spheroidal form and substantially free of flake graphite. It contains some carbides and sufficient alloy content to produce an austenitic structure.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A439 −83(Reapproved 2009)
Standard Specification for
1
Austenitic Ductile Iron Castings
This standard is issued under the fixed designation A439; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 3.1.1 ASTM designation,
3.1.2 Type of austenitic ductile iron required (see 6.1),
1.1 This specification covers austenitic ductile iron castings,
which are used primarily for their resistance to heat, corrosion, 3.1.3 Heat treatment required (see 4.2 – 4.4),
and wear, and for other special purposes.
3.1.4 If repair of castings is permitted (see 4.5),
1.2 Austenitic ductile iron, also known as austenitic nodular 3.1.5 Size and number of test bars required (see 9.1 – 9.4
iron or austenitic spheroidal iron, is characterized by having its
and 10.1),
graphite substantially in a spheroidal form and substantially
3.1.6 Special tests, if required (see 12.1),
free of flake graphite. It contains some carbides and sufficient
3.1.7 Certification, if required (see 14.1), and
alloy content to produce an austenitic structure.
3.1.8 Different preparation for delivery requirements, if
1.3 The values stated in inch-pound units are to be regarded
needed (see 15.1).
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
4. Manufacture
and are not considered standard.
4.1 Melting may be done in any furnaces that produce
2. Referenced Documents
castings meeting the chemical and mechanical requirements
2
outlined in this specification. These include cupolas, air
2.1 ASTM Standards:
furnaces, electric furnaces, crucible furnaces, etc.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
4.2 By agreement between the manufacturer and the
A732/A732M Specification for Castings, Investment, Car-
purchaser, the castings may be stress relieved by heating to
bon and Low Alloy Steel for General Application, and
1150 to 1200°F (621 to 650°C) for not less than 1 h nor more
Cobalt Alloy for High Strength at Elevated Temperatures
than 2 h per inch of thickness in the thickest section. Heating
E8 Test Methods for Tension Testing of Metallic Materials
and cooling shall be uniform and shall not be more than 400°F
3
E30 Methods for Chemical Analysis of Ferroalloys
(222°C)/h for castings less than 1 in. (25.4 mm) in maximum
E59 Practice for Sampling Steel and Iron for Determination
thickness, nor more than 400°F (222°C) divided by the
3
of Chemical Composition
maximum section thickness in inches for thicker castings.
E351 Test Methods for ChemicalAnalysis of Cast Iron—All
During the cooling cycle, castings may be cooled in still air
Types
after the temperature has dropped to 600°F (315°C).
3. Ordering Information
4.3 Whenever dimensional changes in high-temperature
service are a problem, by agreement between the manufacturer
3.1 Orders for material to this specification shall include the
and the purchaser, the castings may be stabilized by heating at
following information:
1600°F (870°C) for 1 h per inch of section, with a minimum of
1 h. Otherwise, the austenite, which is super-saturated with
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
respect to carbon, may reject carbon during service and
Castings and is the direct responsibility of Subcommittee A04.02 on Malleable and
Ductile Iron Castings. produce dimensional changes.
Current edition approved May 1, 2009. Published August 2009. Originally
approved in 1960. Last previous edition approved in 2004 as A439 - 83 (2004). 4.4 By agreement between the manufacturer and the
DOI: 10.1520/A0439-83R09.
purchaser, castings with chilled edges or excessive carbides
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
may be annealed at 1750 to 1900°F (955 to 1040°C) for ⁄2 to
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
5 h followed by uniform cooling, preferably in still air.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4.5 Repairbywelding,plugging,orotherapprovedmethods
Withdrawn. The last approved version of this historical standard is referenced
on www.astm.org. may be done only with written permission from the purchaser.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A439−83 (2009)
5. Magnetic Properties 8. Workmanship, Finish, and Appearance
5.1 In the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.