ASTM F1760-16
(Specification)Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
ABSTRACT
This specification has been published in response to the special circumstance of regulatory requirements regarding federal procurement guidelines for plastic pipe having recycled content. This specification covers coextruded Poly(Vinyl Chloride) (PVC) plastic pipe with a center layer and concentric inner and outer solid layers. The pipe is produced using a multi-layer coextrusion die. The inner and outer layers are made of virgin PVC compound and the center layer has reprocessed-recycled PVC content. The pipe is for nonpressure use in three series: Sewer-Drain series; IPS Schedule 40 series; and IPS Pipe Stiffness (PS) series. Quality control test requirement: nondestructive testing; impact resistance; bond integrity; flattening integrity; pipe stiffness; joint integrity, solvent-cement joints; and joint integrity, elastomeric-gasket joints shall be performed to conform with the specified requirements.
SCOPE
1.1 This specification has been published in response to the special circumstance of regulatory requirements regarding federal procurement guidelines for plastic pipe having recycled content.
1.2 This specification covers coextruded Poly(Vinyl Chloride) (PVC) plastic pipe with a center layer and concentric inner and outer solid layers. The pipe is produced using a multi-layer coextrusion die. The inner and outer layers are made of virgin PVC compound and the center layer has reprocessed-recycled PVC content. The pipe is for non-pressure use in three series:
1.2.1 Sewer-Drain series with a sewer-pipe (PSM) outside diameter and a pipe stiffness of 46 psi (320 kPa),
1.2.2 IPS Schedule 40 series, and
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of 100 psi (690 kPa) and 120 psi (830 kPa).
1.3 Pipe that is outside-diameter controlled does not have an inside diameter suitable for use as a fitting socket.
1.4 All pipe series are allowed to be perforated during production.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1760 −16 An American National Standard
Standard Specification for
Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic
1
Pipe Having Reprocessed-Recycled Content
This standard is issued under the fixed designation F1760; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification has been published in response to the
2.1 ASTM Standards:
special circumstance of regulatory requirements regarding
D883 Terminology Relating to Plastics
federalprocurementguidelinesforplasticpipehavingrecycled
D1243 Test Method for Dilute Solution Viscosity of Vinyl
content.
Chloride Polymers
D1600 Terminology forAbbreviatedTerms Relating to Plas-
1.2 This specification covers coextruded Poly(Vinyl Chlo-
tics
ride) (PVC) plastic pipe with a center layer and concentric
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)
inner and outer solid layers. The pipe is produced using a
Compounds and Chlorinated Poly(Vinyl Chloride)
multi-layer coextrusion die. The inner and outer layers are
(CPVC) Compounds
made of virgin PVC compound and the center layer has
D2122 Test Method for Determining Dimensions of Ther-
reprocessed-recycled PVC content. The pipe is for non-
moplastic Pipe and Fittings
pressure use in three series:
D2412 Test Method for Determination of External Loading
1.2.1 Sewer-Drain series with a sewer-pipe (PSM) outside
Characteristics of Plastic Pipe by Parallel-Plate Loading
diameter and a pipe stiffness of 46 psi (320 kPa),
D2444 Test Method for Determination of the Impact Resis-
1.2.2 IPS Schedule 40 series, and
tance of Thermoplastic Pipe and Fittings by Means of a
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of
Tup (Falling Weight)
100 psi (690 kPa) and 120 psi (830 kPa).
D2466 Specification for Poly(Vinyl Chloride) (PVC) Plastic
1.3 Pipethatisoutside-diametercontrolleddoesnothavean
Pipe Fittings, Schedule 40
inside diameter suitable for use as a fitting socket.
D2467 Specification for Poly(Vinyl Chloride) (PVC) Plastic
1.4 All pipe series are allowed to be perforated during
Pipe Fittings, Schedule 80
production.
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic
Drain, Waste, and Vent Pipe and Fittings
1.5 The values stated in inch-pound units are to be regarded
D2855 Practice for the Two-Step (Primer and Solvent Ce-
as standard. The values given in parentheses are mathematical
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
conversions to SI units that are provided for information only
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
and are not considered standard.
Piping Components with Tapered Sockets
1.6 This standard does not purport to address all of the
D3034 Specification for Type PSM Poly(Vinyl Chloride)
safety concerns, if any, associated with its use. It is the
(PVC) Sewer Pipe and Fittings
responsibility of the user of this standard to establish appro-
D3212 Specification for Joints for Drain and Sewer Plastic
priate safety and health practices and determine the applica-
Pipes Using Flexible Elastomeric Seals
bility of regulatory limitations prior to use.
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC)
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl
2
Based Pipe. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved April 1, 2016. Published June 2016. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1996. Last previous edition approved in 2011 as F1760–01(2011). DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F1760-16. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1760−16
and Chlorinated Poly(Vinyl Chloride) (CPVC) Com- and reprocessed into raw materials. Identity of finished goods
pounds for Plastic Pipe and Fittings Used in Nonpressure is known by the reprocessing company.
Applications
3.2.7 thermoplastic coextruded pipe—pipe consisting of
D5260 Classification for Chemical Resistance of Poly(Vinyl
two or more concentric thermoplastic layers formed through
Chloride) (PVC) Homopolymer and Copolymer Com-
the process of coextrusion.
pounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds 4. Classification
F412 Terminology Relating to Plastic Piping
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1760 − 01 (Reapproved 2011) F1760 − 16
Standard Specification for
Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic
1
Pipe Having Reprocessed-Recycled Content
This standard is issued under the fixed designation F1760; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification has been published in response to the special circumstance of regulatory requirements regarding federal
procurement guidelines for plastic pipe having recycled content.
1.2 This specification covers coextruded Poly(Vinyl Chloride) (PVC) plastic pipe with a center layer and concentric inner and
outer solid layers. The pipe is produced using a multi-layer coextrusion die. The inner and outer layers are made of virgin PVC
compound and the center layer has reprocessed-recycled PVC content. The pipe is for non-pressure use in three series:
1.2.1 Sewer-Drain series with a sewer-pipe (PSM) outside diameter and a pipe stiffness of 46 psi (320 kPa),
1.2.2 IPS Schedule 40 series, and
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of 100 psi (690 kPa) and 120 psi (830 kPa).
1.3 Pipe that is outside-diameter controlled does not necessarily have an inside diameter suitable for use as a fitting socket.
1.4 All series may be perforated.pipe series are allowed to be perforated during production.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
D1243 Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D2466 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
D2467 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D2665 Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
D2855 Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated
Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
D3034 Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl Based
Pipe.
Current edition approved Feb. 1, 2011April 1, 2016. Published March 2011June 2016. Originally approved in 1996. Last previous edition approved in 20052011 as
ε1
F1760–01(2005)F1760–01(2011). . DOI: 10.1520/F1760-01R11.10.1520/F1760-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1760 − 16
D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for
Plastic Pipe and Fittings Used in Nonpressure Applications
D5260 Classification for Chemical Resistance of Poly(Vinyl Chloride) (PVC) Hom
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.