ASTM F1760-01

Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content

SCOPE
1.1 This specification has been published in response to the special circumstance of regulatory requirements regarding federal procurement guidelines for plastic pipe having recycled content.
1.2 This specification covers coextruded Poly(Vinyl Chloride) (PVC) plastic pipe with a center layer and concentric inner and outer solid layers. The pipe is produced using a multi-layer coextrusion die. The inner and outer layers are made of virgin PVC compound and the center layer has reprocessed-recycled PVC content. The pipe is for non-pressure use in three series:
1.2.1 Sewer-Drain series with a sewer-pipe outside diameter and a pipe stiffness of 46 psi (320 kPa),
1.2.2 IPS Schedule 40 series, and
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of 100 psi (690 kPa) and 120 psi (830 kPa).
1.3 Pipe that is outside-diameter controlled does not necessarily have an inside diameter suitable for use as a fitting socket.
1.4 All series may be perforated.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI values are provided for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Apr-2001
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.25 - Vinyl Based Pipe

Relations

• Replaces: ASTM F1760-97 - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
• Effective Date: 10-Apr-2001
• Replaced By: ASTM F1760-01(2005)e1 - Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content
• Effective Date: 01-Nov-2005
• Referred By: ASTM F1336-20 - Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
• Effective Date: 10-Apr-2001
• Referred By: ASTM F412-23 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 10-Apr-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1760 – 01
Standard Specification for
Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic
1
Pipe Having Reprocessed-Recycled Content
This standard is issued under the fixed designation F 1760; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope D 1784 Specification for Rigid Poly(Vinyl Chloride) Com-
pounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
1.1 This specification has been published in response to the
2
Compounds
special circumstance of regulatory requirements regarding
D 2122 Test Method for Determining Dimensions of Ther-
federalprocurementguidelinesforplasticpipehavingrecycled
3
moplastic Pipe and Fittings
content.
D 2412 Test Method for Determination of External Loading
1.2 This specification covers coextruded Poly(Vinyl Chlo-
3
Characteristics of Plastic Pipe by Parallel-Plate Loading
ride) (PVC) plastic pipe with a center layer and concentric
D 2444 Test Method for Determination of the Impact Re-
inner and outer solid layers. The pipe is produced using a
sistance of Thermoplastic Pipe and Fittings by Means of a
multi-layer coextrusion die. The inner and outer layers are
3
Tup (Falling Weight)
made of virgin PVC compound and the center layer has
D 2466 Specification for Poly(Vinyl Chloride) (PVC) Plas-
reprocessed-recycled PVC content. The pipe is for non-
3
tic Pipe Fittings, Schedule 40
pressure use in three series:
D 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-
1.2.1 Sewer-Drainserieswithasewer-pipeoutsidediameter
3
tic Drain, Waste, and Vent Pipe and Fittings
and a pipe stiffness of 46 psi (320 kPa),
D 2855 Practice for Making Solvent-Cemented Joints with
1.2.2 IPS Schedule 40 series, and
3
Poly(Vinyl Chloride) (PVC) Pipe and Fittings
1.2.3 IPS Pipe Stiffness (PS) series with pipe stiffnesses of
D 3034 Specification for Type PSM Poly(Vinyl Chloride)
100 psi (690 kPa) and 120 psi (830 kPa).
3
(PVC) Sewer Pipe and Fittings
1.3 Pipe that is outside-diameter controlled does not neces-
D 3212 Specification for Joints for Drain and Sewer Plastic
sarily have an inside diameter suitable for use as a fitting
3
Pipes Using Flexible Elastomeric Seals
socket.
D 4396 Specification for Rigid Poly(Vinyl Chloride) (PVC)
1.4 All series may be perforated.
Compounds and Chlorinated Poly(Vinyl Chloride) (PVC)
1.5 The values stated in inch-pound units are to be regarded
Compounds for Plastic Pipe and Fittings Used in Nonpres-
as the standard. The SI values are provided for information
4
sure Applications
only.
3
F 412 Terminology Relating to Plastic Piping Systems
1.6 This standard does not purport to address all of the
F 477 Specification for Elastomeric Seals (Gaskets) for
safety concerns, if any, associated with its use. It is the
3
Joining Plastic Pipe
responsibility of the user of this standard to establish appro-
F 512 Specification for Smooth-Wall Poly(Vinyl Chloride)
priate safety and health practices and determine the applica-
3
(PVC) Conduit and Fittings for Underground Installation
bility of regulatory limitations prior to use.
F 1336 Specification for Poly(Vinyl Chloride) (PVC) Gas-
3
2. Referenced Documents keted Sewer Fittings
F 1365 Test Method for Water Infiltration Resistance of
2.1 ASTM Standards:
2
Plastic Underground Conduit Joints Which Use Flexible
D 883 Terminology Relating to Plastics
3
Elastomeric Seals
D 1243 Test Method for Dilute Solution Viscosity of Vinyl
5
2
2.2 Plastic Pipe Institute Technical Report:
Chloride Polymers
PPI-TR-7 Recommended Method for Calculation of Nomi-
D 1600 Terminology for Abbreviated Terms Relating to
2
nal Weight of Plastic Pipe
Plastics
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.25 on Vinyl
3
Based Pipe. Annual Book of ASTM Standards, Vol 08.04.
4
Current edition approved April 10, 2001. Published May 2001. Originally Annual Book of ASTM Standards, Vol 08.03.
5
published as F 1760–96. Last previous edition F 1760–97. Available from Plastic Pipe Institute, 1275 K Street NW, Suite 400, Washing-
2
Annual Book of ASTM Standards, Vol 08.01. ton, DC 20005.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F1760–01
TABLE 2 SI Requirements for Sewer-Drain Pipe
3. Terminology
Nominal Average Tolerance on Minimum Wall Impact
3.1 Definitions—Definitions are in accordance with Termi-
A
Size, in. OD, mm Average, mm Thickness, mm Resistance, J
nologiesD 883,D 1600,andF 412,unlessother
...