ASTM C29/C29M-97(2003)

Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate

SCOPE
1.1 This test method covers the determination of bulk density ("unit weight") of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 5 in. [125 mm] in nominal maximum size.
Note 1—Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in Specification E 11. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore each system must be used independently of the other, without combining values in any way.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Jul-1997
• ICS: 19.060 - Mechanical testing
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.20 - Aggregates

Relations

• Replaces: ASTM C29/C29M-97 - Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
• Effective Date: 10-Jul-1997
• Replaced By: ASTM C29/C29M-07 - Standard Test Method for Bulk Density ("Unit Weight") and Voids in Aggregate
• Effective Date: 01-Aug-2007
• Referred By: ASTM C128-22 - Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
• Effective Date: 10-Jul-1997
• Referred By: ASTM C331/C331M-23 - Standard Specification for Lightweight Aggregates for Concrete Masonry Units
• Effective Date: 10-Jul-1997
• Referred By: ASTM D1369-19 - Standard Practice for Quantities of Materials for Asphalt-Aggregate Surface Treatments
• Effective Date: 10-Jul-1997
• Referred By: ASTM C476-23 - Standard Specification for Grout for Masonry
• Effective Date: 10-Jul-1997
• Referred By: ASTM D692/D692M-20 - Standard Specification for Coarse Aggregate for Asphalt Paving Mixtures
• Effective Date: 10-Jul-1997
• Referred By: ASTM D6155-19 - Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures
• Effective Date: 10-Jul-1997
• Referred By: ASTM E701-80(2018) - Standard Test Methods for Municipal Ferrous Scrap
• Effective Date: 10-Jul-1997
• Referred By: ASTM C566-19 - Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying
• Effective Date: 10-Jul-1997
• Referred By: ASTM D6023-16 - Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM)
• Effective Date: 10-Jul-1997
• Referred By: ASTM C332-23 - Standard Specification for Lightweight Aggregates for Insulating Concrete
• Effective Date: 10-Jul-1997
• Referred By: ASTM C173/C173M-16 - Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
• Effective Date: 10-Jul-1997
• Referred By: ASTM C1252-23 - Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading)
• Effective Date: 10-Jul-1997
• Referred By: ASTM C1170/C1170M-20 - Standard Test Method for Determining Consistency and Density of Roller-Compacted Concrete Using a Vibrating Table
• Effective Date: 10-Jul-1997

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
American Association of State
Designation:C29/C29M–97(Reapproved2003) Highway and Transportation Officials Standard
AASHTO No.: T19/T19M
Standard Test Method for
1
Bulk Density (“Unit Weight”) and Voids in Aggregate
This standard is issued under the fixed designation C29/C29M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
2
1. Scope for Test Methods for Construction Materials
C702 Practice for Reducing Samples of Aggregate to
1.1 This test method covers the determination of bulk
2
Testing Size
density (“unit weight”) of aggregate in a compacted or loose
3
D75 Practice for Sampling Aggregates
condition, and calculated voids between particles in fine,
4
D123 Terminology Relating to Textiles
coarse, or mixed aggregates based on the same determination.
E11 Specification for Wire Cloth and Sieves for Testing
Thistestmethodisapplicabletoaggregatesnotexceeding5in.
5
Purposes
[125 mm] in nominal maximum size.
2.2 AASHTO Standard:
NOTE 1—Unitweightisthetraditionalterminologyusedtodescribethe
T19/T19M Method of Test for Unit Weight and Voids in
property determined by this test method, which is weight per unit volume
6
Aggregate
(more correctly, mass per unit volume or density).
1.2 The values stated in either inch-pound units or SI units 3. Terminology
are to be regarded separately as standard, as appropriate for a
3.1 Definitions—Definitions are in accordance with Termi-
specificationwithwhichthistestmethodisused.Anexception
nology C125 unless otherwise indicated.
is with regard to sieve sizes and nominal size of aggregate, in
3.1.1 bulk density, n—of aggregate, the mass of a unit
which the SI values are the standard as stated in Specification
volume of bulk aggregate material, in which the volume
E11. Within the text, SI units are shown in brackets. The
includes the volume of the individual particles and the volume
3 3
values stated in each system may not be exact equivalents;
ofthevoidsbetweentheparticles.Expressedinlb/ft [kg/m ].
thereforeeachsystemmustbeusedindependentlyoftheother,
3.1.2 unit weight, n—weight (mass) per unit volume. (Dep-
without combining values in any way.
recated term used–preferred term bulk density.)
1.3 This standard does not purport to address all of the
3.1.2.1 Discussion—Weightisequaltothemassofthebody
safety concerns, if any, associated with its use. It is the
multiplied by the acceleration due to gravity. Weight may be
responsibility of the user of this standard to establish appro-
expressed in absolute units (newtons, poundals) or in gravita-
priate safety and health practices and determine the applica-
tional units (kgf, lbf), for example: on the surface of the earth,
bility of regulatory limitations prior to use.
a body with a mass of 1 kg has a weight of 1 kgf (approxi-
mately 9.81 N), or a body with a mass of 1 lb has a weight of
2. Referenced Documents
1 lbf (approximately 4.45 N or 32.2 poundals). Since weight is
2.1 ASTM Standards:
equal to mass times the acceleration due to gravity, the weight
C125 Terminology Relating to Concrete and Concrete
of a body will vary with the location where the weight is
2
Aggregates
determined, while the mass of the body remains constant. On
C127 Test Method for Density, Relative Density (Specific
the surface of the earth, the force of gravity imparts to a body
2
2
Gravity), and Absorption of Coarse Aggregate
that is free to fall an acceleration of approximately 9.81 m/s
2
C128 Test Method for Density, Relative Density (Specific
(32.2 ft/s ). D 123
2
Gravity), and Absorption of Fine Aggregate
3.2 Definitions of Terms Specific to This Standard:
C138/C138M Test Method for Density (Unit Weight),
3.2.1 voids, n—in unit volume of aggregate, the space
2
Yield, and Air Content (Gravimetric) of Concrete
between particles in an aggregate mass not occupied by solid
C670 Practice for Preparing Precision and Bias Statements
mineral matter.
1
This test method is under the jurisdiction of ASTM Committee C09 on
3
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee Annual Book of ASTM Standards, Vol 04.03.
4
C09.20 on Normal Weight Aggregates. Annual Book of ASTM Standards, Vol 07.01.
5
Current edition approved July 10, 1997. Published September 1997. Originally Annual Book of ASTM Standards, Vol 14.02.
6
approved in 1920. Last previous edition approved in 1991 as C29/C29M–91a. Available from American Association of State Highway and Transportation
2
Annual Book of ASTM Standards, Vol 04.02. Officials, 444 N. Capitol St. NW, Suite 225, Washington, DC 20
...