iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D7910-14

(Practice)

Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift

Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift

SIGNIFICANCE AND USE
4.1 This practice defines a consistent procedure for collecting surface material using clear, transparent, single sided adhesive collection medium, typically tape (also known as tape lift).  
4.2 A tape lift sample collected according to this practice is intended to be used to assess the material present at one specific location on a surface for fungal content.  
4.3 A tape lift sample collected from a point of interest can be used for qualitative analysis or to quantify fungal material per sample or per unit area. Note that the recovery efficiency of material from the surface sampled is unknown and a likely source of uncertainty for quantitative analyses.  
4.4 A tape lift sample collected according to this practice can be analyzed by direct microscopy.  
4.5 This practice may help supplement consistency in mold sampling during an indoor air quality investigation.
SCOPE
1.1 This practice describes the protocols for collection of surface samples using tape lifts and their delivery to the laboratory.  
1.2 The purpose of this practice is to support the field investigator in differentiating fungal materials from non-fungal material such as scuffs, soot deposits, stains, pigments, dust, efflorescence, adhesives, and water stains.  
1.3 The samples collected by this practice are appropriate for either qualitative or quantitative analysis by direct microscopy.  
1.4 This practice does not address building occupant exposures, or occupant health risks.  
1.5 This practice does not address the development of a formal hypothesis or the establishment of sampling objectives.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-May-2014
ICS
07.100.99 - Other standards related to microbiology
Technical Committee
D22 - Air Quality
Drafting Committee
D22.08 - Assessment, Sampling, and Analysis of Microorganisms
Current Stage
Ref Project

Buy Standard

ASTM D7910-14 - Standard Practice for Collection of Fungal Material From Surfaces by Tape LiftASTM D7910-14 - Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift
PreviousNext
Standard
ASTM D7910-14 - Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7910 − 14
Standard Practice for
1
Collection of Fungal Material From Surfaces by Tape Lift
This standard is issued under the fixed designation D7910; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This practice describes the protocols for collection of 2.1 ASTM Standards:
surface samples using tape lifts and their delivery to the D1356 Terminology Relating to Sampling and Analysis of
laboratory.
Atmospheres
D4840 Guide for Sample Chain-of-Custody Procedures
1.2 The purpose of this practice is to support the field
D6044 Guide for Representative Sampling for Management
investigator in differentiating fungal materials from non-fungal
of Waste and Contaminated Media
material such as scuffs, soot deposits, stains, pigments, dust,
efflorescence, adhesives, and water stains.
3. Terminology
1.3 The samples collected by this practice are appropriate
3.1 Definitions—For terminology not defined herein, refer
for either qualitative or quantitative analysis by direct micros-
to Terminology D1356.
copy.
3.2 Definitions of Terms Specific to This Standard:
1.4 This practice does not address building occupant
3.2.1 area (surface, sampled), n—a defined, measured ex-
exposures, or occupant health risks.
tent of surface sampled.
1.5 This practice does not address the development of a
3.2.2 chain of custody (COC), n—a document that provides
formal hypothesis or the establishment of sampling objectives.
for the traceable transfer of field samples to the analytical
1.6 The values stated in SI units are to be regarded as
laboratory. It may or may not be combined with the field data
standard. No other units of measurement are included in this
sheet. D4840
standard.
3.2.3 direct microscopy analysis, n—act of assessing micro-
1.7 This standard does not purport to address all of the
organisms (if present) using an optical compound microscope.
safety concerns, if any, associated with its use. It is the
3.2.4 field data sheet, n—a record of varying names that
responsibility of the user of this standard to establish appro-
provides a reference document for information directly related
priate safety, health, and environmental practices and deter-
to the sample collection event, including pre- and post-
mine the applicability of regulatory limitations prior to use.
calibration data.
1.8 This international standard was developed in accor-
3.2.5 fungal material, n—fungal spores, hyphae, and repro-
dance with internationally recognized principles on standard-
ductive structures.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
3.2.6 fungal structure (sing.), n—collective term for frag-
mendations issued by the World Trade Organization Technical
ments or groups of fragments from fungi, including but not
Barriers to Trade (TBT) Committee.
limited to conidia, conidiophores, hyphae and spores.
3.2.7 fungi (pl.), n—eukaryotic, heterotrophic, absorptive
organisms that usually develop a rather diffuse, branched,
tubular body (that is, network of hyphae) and usually repro-
3
duce by means of spores. The terms ‘mold’and ‘mildew’are
frequently used by laypersons when referring to various fungal
colonization.
1 2
This practice is under the jurisdiction ofASTM Committee D22 on Air Quality For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and is the direct responsibility of Subcommittee D22.08 on Assessment, Sampling, contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Analysis of Microorganisms. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved June 1, 2014. Published July 2014. DOI: 10.1520/ the ASTM website.
3
D7910-14. Kendrick, B., The Fifth Kingdom, Focus Publishing / R. Pullins & Co, 2008.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7910 − 14
3.2.8 sample, n—a portion of material that is taken for 6.3 For adhesive tape sampling, perform the following
testing or record purposes. D6044 steps:
6.3.1 Removeanddiscardtapethathasbeenexposed(many
4. Significance and Use typical dispensers leave an area of tape exposed between the
roll and the cutter edge).
4.1 This practice defines a consistent procedure for collect-
6.3.2 Remove or dispense enough unexposed adhesive tape
ing surface material using clear, transparent, single sided
to take a surface sample. A tape strip 2.5 to 5.0 cm long is
adhesivecollecti
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6329-98(2023)(Guide)
Standard Guide for Developing Methodology for Evaluating the Ability of Indoor Materials to Support Microbial Growth Using Static Environmental Chambers

SIGNIFICANCE AND USE
4.1 The static chambers have several different applications:  
4.1.1 The static chambers can be used to compare the susceptibility of different materials to the colonization and amplification of various microorganisms under defined conditions.  
4.1.2 Chambers operated at high relative humidities may be used to perform worst case scenario screening tests on materials by providing an atmosphere where environmental conditions may be favorable for microbial growth.  
4.1.3 Use of multiple chambers with different environmental parameters, such as a range of relative humidities, permits the evaluation of multiple microenvironments and allows investigation of materials under differing environmental conditions.  
4.1.4 Drying requirements for wetted materials may also be investigated. This information may be relevant for determining material resistance to microbial growth after becoming wet. These conditions may simulate those where materials are subjected to water incursion through leaks as well as during remediation of a building after a fire.  
4.1.5 Growth rates of microorganisms on the material may also be investigated. Once it has been established that organisms are able to grow on a particular material under defined conditions, investigations into the rate of organism growth may be performed. These evaluations provide base line information and can be used to evaluate methods to limit or contain amplification of microorganisms.  
4.2 These techniques should be performed by personnel with training in microbiology. The individual must be competent in the use of sterile technique, which is critical to exclude external contamination of materials.
SCOPE
1.1 Many different types of microorganisms (for example, bacteria, fungi, viruses, algae) can occupy indoor spaces. Materials that support microbial growth are potential indoor sources of biocontaminants (for example, spores and toxins) that can become airborne indoor biopollutants. This guide describes a simple, relatively cost effective approach to evaluating the ability of a variety of materials to support microbial growth using a small chamber method.  
1.2 This guide is intended to assist groups in the development of specific test methods for a definite material or groups of materials.  
1.3 Static chambers have certain limitations. Usually, only small samples of indoor materials can be evaluated. Care must be taken that these samples are representative of the materials being tested so that a true evaluation of the material is performed.  
1.4 Static chambers provide controlled laboratory microenvironment conditions. These chambers are not intended to duplicate room conditions, and care must be taken when interpreting the results. Static chambers are not a substitute for dynamic chambers or field studies.  
1.5 A variety of microorganisms, specifically bacteria and fungi, can be evaluated using these chambers. This guide is not intended to provide human health effect data. However, organisms of clinical interest, such as those described as potentially allergenic, may be studied using this approach.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM D7789-21(Practice)
Standard Practice for Collection of Fungal Material from Surfaces by Swab

SIGNIFICANCE AND USE
4.1 This practice provides a procedure for collecting surface material using a sterile swab.  
4.2 A swab sample collected according to this practice is intended to be used to assess fungal material on surfaces.  
4.3 A swab sample collected from an area with defined dimensions can be used to quantify fungal material per unit area or for qualitative analysis.  
4.4 A swab sample collected from point(s) of interest can be used for qualitative analysis or to quantify fungal material per sample.  
4.5 A swab sample collected according to this practice can be analyzed by direct microscopy, culture, or biochemical analysis.
SCOPE
1.1 The purpose of this practice is to describe the procedures for collection of surface samples using sterile swabs.  
1.2 The purpose of this practice is to support the field investigator in differentiating fungal materials from non-fungal material such as scuffs, soot deposits, stains, pigments, dust, efflorescence, adhesives, dust, and water stains.  
1.3 This practice does not address building occupant exposures, or occupant health risks.  
1.4 The samples collected by this practice are appropriate for culture, direct microscopy, and biochemical analysis, or combination thereof.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D7658-17(2021)(Test Method)
Standard Test Method for Direct Microscopy of Fungal Structures from Tape

SIGNIFICANCE AND USE
5.1 The significance of this test method is to standardize the analysis of the detection of removable fungal structures lifted from a surface with tape to improve consistency between laboratories and analysts.  
5.2 This test method is intended to ensure consistent data to the end user.  
5.3 Fungal structures are identified and semi-quantified regardless of whether they would or would not grow in culture.  
5.4 It must be emphasized that the detector in this test method is the analyst, and therefore results are subjective, depending on the experience, training, qualification, optical acuity, and mental fatigue of the analyst.  
5.5 This test method can be used to assess the presence and characteristics of fungal material on a surface.
SCOPE
1.1 This test method uses optical microscopy for the detection, semi-quantification, and identification of fungal structures in tape lift preparations.  
1.2 This test method describes the preparation techniques for tape-lift matrices, the procedure for confirming the presence of fungal structures, and the reporting of observed fungal structures  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7910-14(2021)(Practice)
Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift

SIGNIFICANCE AND USE
4.1 This practice defines a consistent procedure for collecting surface material using clear, transparent, single sided adhesive collection medium, typically tape (also known as tape lift).  
4.2 A tape lift sample collected according to this practice is intended to be used to assess the material present at one specific location on a surface for fungal content.  
4.3 A tape lift sample collected from a point of interest can be used for qualitative analysis or to quantify fungal material per sample or per unit area. Note that the recovery efficiency of material from the surface sampled is unknown and a likely source of uncertainty for quantitative analyses.  
4.4 A tape lift sample collected according to this practice can be analyzed by direct microscopy.  
4.5 This practice may help supplement consistency in mold sampling during an indoor air quality investigation.
SCOPE
1.1 This practice describes the protocols for collection of surface samples using tape lifts and their delivery to the laboratory.  
1.2 The purpose of this practice is to support the field investigator in differentiating fungal materials from non-fungal material such as scuffs, soot deposits, stains, pigments, dust, efflorescence, adhesives, and water stains.  
1.3 The samples collected by this practice are appropriate for either qualitative or quantitative analysis by direct microscopy.  
1.4 This practice does not address building occupant exposures, or occupant health risks.  
1.5 This practice does not address the development of a formal hypothesis or the establishment of sampling objectives.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7391-20(Test Method)
Standard Test Method for Categorization and Quantification of Airborne Fungal Structures in an Inertial Impaction Sample by Optical Microscopy

SIGNIFICANCE AND USE
5.1 This test method is used to estimate and categorize the number and type of fungal structures present on an inertial impactor sample.  
5.2 Fungal structures are identified and quantified regardless of whether they would or would not grow in culture.  
5.3 It must be emphasized that the detector in this test method is the analyst, and therefore results are subjective, depending on the experience, training, qualification, and mental and optical fatigue of the analyst.
SCOPE
1.1 This test method is a procedure that uses direct microscopy to analyze the deposit on an inertial impaction sample.  
1.2 This test method describes procedures for categorizing and enumerating fungal structures by morphological type. Typically, categories may be as small as genus (for example, Cladosporium) or as large as phylum (for example, basidiospores).  
1.3 This test method contains two procedures for enumerating fungal structures: one for slit impaction samples and one for circular impaction samples. This test method is applicable for impaction air samples, for which a known volume of air (at a rate as recommended by the manufacturer) has been drawn, and is also applicable for blank impaction samples.  
1.4 Enumeration results are presented in fungal structures/sample (fs/sample) and fungal structures/m3 (fs/m3).  
1.5 The range of enumeration results that can be determined with this test method depends on the size of the spores on the sample trace, the amount of particulate matter on the sample trace, the percentage of the sample trace counted, and the volume of air sampled.  
1.6 This test method addresses only the analysis of samples. The sampling process and interpretation of results is outside the scope of this test method.  
1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM D8068-19(Practice)
Standard Practice for Collection of Culturable Airborne Fungi or Bacteria on Agar Plates by Inertial Impaction Systems

SIGNIFICANCE AND USE
4.1 This practice is intended for the collection of airborne particles on agar plates using inertial impaction for the purpose of culturing fungi or bacteria.  
4.2 This practice is valuable when species level identification or quantity of culturable aerosolized fungi and bacteria are important factors for the indoor air quality investigation.  
4.3 It is the responsibility of the user to assure that they are in compliance with all local, state, and federal regulations governing the inspection of buildings for fungal and bacterial colonization and the collection of associated samples.  
4.4 This practice is intended to provide the user with a basic understanding of the equipment, materials, and instructions necessary to effectively collect air samples on agar plates using an inertial impactor.  
4.5 This practice is intended to minimize systematic sampling variations between different data sets.
SCOPE
1.1 The purpose of this practice is to describe procedures for the collection of culturable airborne fungal spores or fragments or bacteria on agar plates using inertial impaction sampling techniques.  
1.2 This practice does not include collection of culturable fungi or bacteria by devices not using agar plates.  
1.3 This practice presumes that the user has a fundamental understanding of field investigative techniques related to the scientific process, and sampling plan development and implementation. It is important to establish the related hypothesis to be tested and the supporting analytical methodology needed in order to identify the sampling media to be used and the laboratory conditions for analysis.  
1.4 This practice does not address the development of a formal hypothesis or the establishment of appropriate and defensible investigation and sampling objectives. It is presumed the investigator has the experience and knowledge base to address these issues.  
1.5 This practice does not provide the user sufficient information to allow for interpretation of the analytical results from sample collection. It is the user's responsibility to seek or obtain the information and knowledge necessary to interpret the sample results reported by the laboratory.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2564-23(Practice)
Standard Practice for Enumeration of Mycobacteria in Metalworking Fluids by Direct Microscopic Counting (DMC) Method

SIGNIFICANCE AND USE
5.1 Measurement of mycobacterial cell count densities is an important step in establishing a possible relationship between mycobacteria and occupational health-related allergic responses, for example, hypersensitivity pneumonitis (HP) in persons exposed to aerosols of metalworking fluids. It is known that the viable mycobacteria count underestimates the total mycobacterial levels by not counting the non-culturable, possibly dead or moribund population that is potentially equally important in the investigation of occupational health-related problems. The direct microscopic counting method (DMC) described here gives a quantitative assessment of the total numbers of acid-fast bacilli. It involves using acid-fast staining to selectively identify mycobacteria from other bacteria, followed by enumeration or direct microscopic counting of a known volume over a known area. Although other microbes—particularly the Actinomycetes—also stain acid-fast, they are differentiated from the mycobacteria because of their morphology and size. Non-mycobacteria, acid-fast microbes are 50 to 100 times larger than mycobacteria. This practice provides quantitative information on the total (culturable and non-culturable viable, and non-viable) mycobacteria populations. The results are expressed quantitatively as mycobacteria per mL of metalworking fluid sample.  
5.2 The DMC method using the acid-fast staining technique is a semi-quantitative method with a relatively fast turnaround time.  
5.3 The DMC method can also be employed in field survey studies to characterize the changes in total mycobacteria densities of metalworking fluid systems over a long period of time.  
5.4 The sensitivity detection limit of the DMC method depends on the MF and the sample volume (direct or centrifuged, etc.) examined.
SCOPE
1.1 This practice describes a direct microscopic counting method (DMC) for the enumeration of the acid-fast stained mycobacteria population in metalworking fluids. It can be used to detect levels of total mycobacteria population, including culturable as well as non-culturable (possibly dead or moribund) bacterial cells. This practice is recommended for all water-based metalworking fluids (Classification D2881).  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For additional safety information, see Laboratory Safety: Principle and Practices, 4th Edition.2  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7816-23(Test Method)
Standard Test Method for Enumeration of Halophilic and Proteolytic Bacteria in Raceway Brine, Brine-Cured Hides and Skins

SIGNIFICANCE AND USE
4.1 This test method enumerates salt tolerant (halophilic) bacteria, and proteolytic bacteria that are also salt tolerant. Under the conditions of this test method those bacteria are equated as halophilic organisms. Salt tolerant proteolytic bacteria have been known to cause damage to hides and skins in raceway brine.
SCOPE
1.1 This test method covers the enumeration of bacteria that can tolerate high salt concentrations or can hydrolyze protein/collagen, or both. This test method is applicable to raceway brine, brine-cured hides and skins, and pre-charge raceway liquor.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7818-23(Test Method)
Standard Test Method for Enumeration of Proteolytic Bacteria in Fresh (Uncured) Hides and Skins

SIGNIFICANCE AND USE
4.1 This test method enumerates proteolytic bacteria. Proteolytic bacteria have been known to cause damage to hides and skins.
SCOPE
1.1 This test method covers the enumeration of bacteria that can hydrolyze protein/collagen in fresh (uncured) hides and skins. This test method is applicable to uncured hides and skins.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E2471-23(Test Method)
Standard Test Method for Using Seeded-Agar for the Screening Assessment of Antimicrobial Activity In Carpets

SIGNIFICANCE AND USE
5.1 This test method provides for rapid screening of antimicrobial treatments located in or on the carpet face fiber or incorporated into the backing structure of the carpet (or both).  
5.2 This test method simulates actual use conditions that may occur on carpets (for example, food and beverage spills, soiling from foot traffic, prolonged moisture exposure).  
5.3 This test method provides a means to screen for activity and durability of an antimicrobial treatment under conditions of organic loading.  
5.4 This test method provides for the simultaneous assessment of multiple carpet components for antimicrobial activity.  
5.5 Carpets may be cleaned prior to testing with this test method in order to assess the durability of the antimicrobial effect.
SCOPE
1.1 This test method is designed to evaluate (qualitatively) the presence of antimicrobial activity in or on carpets. Use this test method to qualitatively evaluate both antibacterial and antifungal activity.  
1.2 Use half strength (nutrient and agar) tryptic soy agar as the inoculum vehicle for bacteria and half strength potato dextrose agar as the inoculum vehicle for mold conidia. Use of half strength agars may reduce undue neutralization of an antimicrobial due to excessive organic load.  
1.3 This test method simultaneously evaluates (both visual and stereo-microscopic) antimicrobial activity both at the fiber layer and at the primary backing layer of carpet.  
1.4 Use this test method to assess the durability of the antimicrobial treatments on new carpets, and on those repeatedly shampooed or exposed to in-use conditions.  
1.5 Knowledge of microbiological techniques is required for the practice of this test method.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off