ASTM D613-10ae1
(Test Method)Standard Test Method for Cetane Number of Diesel Fuel Oil
Standard Test Method for Cetane Number of Diesel Fuel Oil
SIGNIFICANCE AND USE
5.1 The cetane number provides a measure of the ignition characteristics of diesel fuel oil in compression ignition engines.
5.2 This test method is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to matching of fuels and engines.
5.3 Cetane number is determined at constant speed in a precombustion chamber type compression ignition test engine. The relationship of test engine performance to full scale, variable speed, variable load engines is not completely understood.
5.4 This test method may be used for unconventional fuels such as synthetics, vegetable oils, and the like. However, the relationship to the performance of such materials in full scale engines is not completely understood.
SCOPE
1.1 This test method covers the determination of the rating of diesel fuel oil in terms of an arbitrary scale of cetane numbers using a standard single cylinder, four-stroke cycle, variable compression ratio, indirect injected diesel engine.
1.2 The cetane number scale covers the range from zero (0) to 100, but typical testing is in the range of 30 to 65 cetane number.
1.3 The values for operating conditions are stated in SI units and are to be regarded as the standard. The values given in parentheses are the historical inch-pound units for information only. In addition, the engine measurements continue to be in inch-pound units because of the extensive and expensive tooling that has been created for these units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For more specific warning statements, see Annex A1.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D613 − 10a
Designation: 41/2000
Standard Test Method for
1
Cetane Number of Diesel Fuel Oil
This standard is issued under the fixed designation D613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorial changes were made to subsection 8.3 in August 2013.
1. Scope* D4175 Terminology Relating to Petroleum, Petroleum
Products, and Lubricants
1.1 This test method covers the determination of the rating
D4177 Practice for Automatic Sampling of Petroleum and
of diesel fuel oil in terms of an arbitrary scale of cetane
Petroleum Products
numbers using a standard single cylinder, four-stroke cycle,
E456 Terminology Relating to Quality and Statistics
variable compression ratio, indirect injected diesel engine.
E542 Practice for Calibration of Laboratory Volumetric
1.2 The cetane number scale covers the range from zero (0)
Apparatus
to 100, but typical testing is in the range of 30 to 65 cetane
E832 Specification for Laboratory Filter Papers
number.
3. Terminology
1.3 ThevaluesforoperatingconditionsarestatedinSIunits
3.1 Definitions:
and are to be regarded as the standard. The values given in
3.1.1 acceptedreferencevalue(ARV),n—avaluethatserves
parentheses are the historical inch-pound units for information
as an agreed-upon reference for comparison, and which is
only. In addition, the engine measurements continue to be in
derived as: (1) a theoretical or established value, based on
inch-pound units because of the extensive and expensive
scientific principles, or (2) an assigned or certified value, based
tooling that has been created for these units.
on experimental work of some national or international
1.4 This standard does not purport to address all of the
organization, or (3) a consensus or certified value, based on
safety concerns, if any, associated with its use. It is the
collaborative experimental work under the auspices of a
responsibility of the user of this standard to establish appro-
scientific or engineering group. E456
priate safety and health practices and determine the applica-
3.1.1.1 Discussion—In the context of this test method,
bility of regulatory limitations prior to use. For more specific
accepted reference value is understood to apply to the cetane
warning statements, see Annex A1.
number of specific reference materials determined empirically
under reproducibility conditions by the National Exchange
2. Referenced Documents
Group or another recognized exchange testing organization.
2
2.1 ASTM Standards:
3.1.2 cetane number (CN), n—a measure of the ignition
D975 Specification for Diesel Fuel Oils
performance of a diesel fuel oil obtained by comparing it to
D1193 Specification for Reagent Water
reference fuels in a standardized engine test. D4175
D2500 Test Method for Cloud Point of Petroleum Products
3.1.2.1 Discussion—In the context of this test method,
D4057 Practice for Manual Sampling of Petroleum and
ignition performance is understood to mean the ignition delay
Petroleum Products
of the fuel as determined in a standard test engine under
controlled conditions of fuel flow rate, injection timing and
compression ratio.
1
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
3.1.3 compression ratio (CR), n—the ratio of the volume of
D02.01 on Combustion Characteristics.
the combustion chamber including the precombustion chamber
Current edition approved Oct. 1, 2010. Published November 2010. Originally
withthepistonatbottomdeadcentertothecomparablevolume
approved in 1941. Last previous edition approved in 2010 as D613–10. DOI:
with the piston at top dead center.
10.1520/D0613-10AE01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.1.4 ignition delay, n—that period of time, expressed in
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
degrees of crank angle rotation, between the start of fuel
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. injection and the start of combustion.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D613 − 10a
3
3.1.5 injection timing (injection advance), n—that time in Diesel National Exchange Group of Subcommittee D02.01 is
the combustion cycle, measured in degrees o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.