iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D2274-03

(Test Method)

Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)

Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)

SCOPE
1.1 This test method covers the measurement of the inherent stability of middle distillate petroleum fuels under specified oxidizing conditions at 95°C.
Note 1—Fuels used in establishing the precision measures for this test method were described as gas oil, diesel fuel, No. 2 heating oil, and DFM, a Navy distillate fuel suitable for diesels, boilers, and gas turbines. (The term DFM is no longer used when referring to fuel meeting MIL-F-16884 requirements; rather it is called F76 as it conforms to NATO F76 requirements.) While the test method may be used for fuels outside the range of these fuels, the precision measures may not apply.
1.2 This test method is not applicable to fuels containing residual oil or significant amounts of components derived from non-petroleum sources.
1.3 The values given in acceptable SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Jun-2003
ICS
75.160.20 - Liquid fuels
Technical Committee
D02 - Petroleum Products, Liquid Fuels, and Lubricants
Drafting Committee
D02.14 - Stability, Cleanliness and Compatibility of Liquid Fuels
Current Stage
Ref Project

Relations

Replaces
ASTM D2274-01a - Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
Effective Date
10-Jun-2003
Replaced By
ASTM D2274-03a - Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
Effective Date
01-Nov-2003
Referred By
ASTM D5967-21 - Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
Effective Date
10-Jun-2003
Referred By
ASTM D4418-22 - Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines
Effective Date
10-Jun-2003
Referred By
ASTM D8048-21ae1 - Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine
Effective Date
10-Jun-2003
Referred By
ASTM D7156-19 - Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
Effective Date
10-Jun-2003
Referred By
ASTM D7422-22 - Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
Effective Date
10-Jun-2003
Referred By
ASTM D7549-23 - Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure
Effective Date
10-Jun-2003
Referred By
ASTM D7451-21 - Standard Test Method for Water Separation Properties of Light and Middle Distillate, and Compression and Spark-Ignition Engine Fuels
Effective Date
10-Jun-2003
Referred By
ASTM D6751-23a - Standard Specification for Biodiesel Fuel Blendstock (B100) for Middle Distillate Fuels
Effective Date
10-Jun-2003
Referred By
ASTM D7468-22 - Standard Test Method for Cummins ISM Test
Effective Date
10-Jun-2003
Referred By
ASTM D8074-22 - Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine
Effective Date
10-Jun-2003
Referred By
ASTM D6468-22 - Standard Test Method for High Temperature Stability of Middle Distillate Fuels
Effective Date
10-Jun-2003
Referred By
ASTM D7583-16(2023) - Standard Test Method for John Deere Coolant Cavitation Test
Effective Date
10-Jun-2003
Referred By
ASTM D6681-23 - Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure
Effective Date
10-Jun-2003

Buy Standard

ASTM D2274-03 - Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)ASTM D2274-03 - Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
PreviousNext
Standard
ASTM D2274-03 - Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D 2274 – 03
Designation: 388/97
Standard Test Method for
Oxidation Stability of Distillate Fuel Oil (Accelerated
1
Method)
This standard is issued under the fixed designation D 2274; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope D 4057 Practice for Manual Sampling of Petroleum and
4
Petroleum Products
1.1 This test method covers the measurement of the inherent
D 4177 Practice for Automatic Sampling of Petroleum and
stability of middle distillate petroleum fuels under specified
4
Petroleum Products
oxidizing conditions at 95°C.
D 4625 Test Method for Distillate Fuel Storage Stability at
NOTE 1—Fuels used in establishing the precision measures for this test 4
43°C (110°F)
method were described as gas oil, diesel fuel, No. 2 heating oil, and DFM,
5
2.2 Military Specification:
a Navy distillate fuel suitable for diesels, boilers, and gas turbines. (The
MIL-F-16884 Fuel, Navy Distillate
term DFM is no longer used when referring to fuel meeting MIL-F-16884
requirements; rather it is called F76 as it conforms to NATO F76
3. Terminology
requirements.) While the test method may be used for fuels outside the
range of these fuels, the precision measures may not apply. 3.1 Definitions of Terms Specific to This Standard:
3.1.1 adherent insolubles (formerly adherent gum)—
1.2 This test method is not applicable to fuels containing
material which is produced in the course of stressing distillate
residual oil or significant amounts of components derived from
fuel under the conditions of this test and which adheres to the
non-petroleum sources.
glassware after fuel has been flushed from the system.
1.3 The values given in acceptable SI units are to be
3.1.2 filterable insolubles—material, which is produced in
regarded as the standard. The values in parentheses are for
the course of stressing distillate fuel under the conditions of
information only.
this test, which is capable of being removed from the fuel by
1.4 This standard does not purport to address all of the
filtration. This includes both material suspended in the fuel and
safety concerns, if any, associated with its use. It is the
material easily removed from the oxidation cell and oxygen
responsibility of the user of this standard to establish appro-
delivery tube with hydrocarbon solvent.
priate safety and health practices and determine the applica-
3.1.3 inherent stability—the resistance to change when
bility of regulatory limitations prior to use.
exposed to air, but in the absence of other environmental
2. Referenced Documents factors such as water, or reactive metallic surfaces and dirt.
3.1.4 total insolubles—sum of the adherent and filterable
2.1 ASTM Standards:
insolubles.
D 381 Test Method for Gum Content in Fuels by Jet
2
3.1.5 zero time—the time the first of a batch of oxidation
Evaporation
cells is placed in the heating bath.
D 943 Test Method for Oxidation Characteristics of Inhib-
2
3.1.5.1 Discussion—This is the time taken as the start of the
ited Mineral Oils
3
16 h of residence in the heating bath.
D 1193 Specification for Reagent Water
4. Summary of Test Method
1 4.1 A 350-mL volume of filtered middle distillate fuel is
This test method is under the jurisdiction of Committee D02 on Petroleum
Products and Lubricants and is the direct responsibility of Subcommittee D02.14 on aged at 95°C (203°F) for 16 h while oxygen is bubbled through
Stability and Cleanliness of Liquid Fuels.
Current edition approved June 10, 2003. Published July 2003. Originally
4
approved in 1964. Last previous edition approved in 2001 as D 2274 – 01a. Annual Book of ASTM Standards, Vol 05.02.
2 5
Annual Book of ASTM Standards, Vol 05.01. Available from Standardization Documents Order Desk, Bldg. 4, 700 Robbins
3
Annual Book of ASTM Standards, Vol 11.01. Ave., Philadelphia, PA 19111-5098. Attn: NPODS
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D2274–03
FIG. 1 Oxidation Cell
the sample at a rate of 3 L/h. After aging, the sample is cooled greater quantities of insolubles to form. Since the apparatus
to approximately room temperature before filtering to obtain used in this test can also be used in Test Method D 943, where
the filterable insolubles quantity. Adherent insolubles are then coils of copper and steel are used, it is important that any
removed from the oxidation cell and associated glassware with residues that co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3701-23(Test Method)
Standard Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic Resonance Spectrometry

SIGNIFICANCE AND USE
5.1 The combustion quality of aviation turbine fuel has traditionally been controlled in specifications by such tests as smoke point (see Test Method D1322), smoke volatility index, aromatic content of luminometer number (see Test Method D1740). Evidence is accumulating that a better control of the quality may be obtained by limiting the minimum hydrogen content of the fuel.  
5.2 Existing methods allow the hydrogen content to be calculated from other parameters or determined by combustion techniques. The method specified provides a quick, simple, and more precise alternative to these methods.
SCOPE
1.1 This test method covers the determination of the hydrogen content of aviation turbine fuels.  
1.2 Use Test Methods D4808 or D7171 for the determination of hydrogen in other petroleum liquids.  
1.3 The values stated in SI units are to be regarded as standard. The preferred units are mass percent hydrogen.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific warning statement, see 7.1.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7826-23b(Guide)
Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives

SIGNIFICANCE AND USE
5.1 This guide is intended for the developers or sponsors of new aviation gasolines or additives to describe the data requirements necessary to support the development of specifications for these new products by ASTM members. The ultimate goal of the data generated in accordance with this guide is to provide an understanding of the performance of the new fuel or additive within the property constraints and compositional bounds of the proposed specification criteria.  
5.2 This guide is not an approval process. It is intended to describe test and analysis requirements necessary to generate data to support specification development. This guide does not address the approval process for ASTM International standards.  
5.3 This guide will reduce the uncertainty and risk to developers or sponsors of new aviation gasolines or additives by describing the test and analysis requirements necessary to proceed with the development of an ASTM International specification for aviation gasoline or specification revision for an aviation gasoline additive. There are certain sections within this guide that do not specify an exact number of data points required. For example, 6.2.4.3 requires viscosity to be measured from freezing point to room temperature; 6.2.4.4, 6.2.4.5, and 6.3.2.3 require measurements over the operating temperature range; 6.3.2.4 and 6.3.2.5 require measurements versus temperature. In these cases, the developers or sponsors of new aviation gasolines or additives should attempt to generate data close to the upper and lower boundaries indicated. If no boundary is specified (for example, generate data versus temperature), then data at the widest practical test limits should be generated. A minimum of three data points is required in all cases (for example, upper, middle, lower), while five or more data points are preferred.  
5.4 This guide does not purport to specify an all-inclusive listing of test and analysis requirements to achieve ASTM International approval ...
SCOPE
1.1 This guide provides procedures to develop data for use in research reports for new aviation gasolines or new aviation gasoline additives.  
1.2 This data is intended to be used by the ASTM subcommittee to make a determination of the suitability of the fuel for use as an aviation fuel in either a fleet-wide or limited capacity, and to make a determination that the proposed properties and criteria in the associated standard specification provide the necessary controls to ensure this fuel maintains this suitability during high-volume production.  
1.3 These research reports are intended to support the development and issuance of new specifications or specification revisions for these products. Guidance to develop ASTM International standard specifications for aviation gasoline is provided in Subcommittee J on Aviation Fuels Operating Procedures, Annex A6, “Guidelines for the Development and Acceptance of a New Aviation Fuel Specification for Spark-Ignition Reciprocating Engines.”  
1.4 The procedures, tests, selection of materials, engines, and aircraft detailed in this guide are based on industry expertise to give appropriate data for review. Because of the diversity of aviation hardware and potential variation in fuel/additive formulations, not every aspect may be encompassed and further work may be required. Therefore, additional data beyond that described in this guide may be requested by the ASTM task force, Subcommittee J, or Committee D02 upon review of the specific composition, performance, or other characteristics of the candidate fuel or additive.  
1.5 While it is beyond the scope of this guide, investigation of the future health and environmental impacts of the new aviation gasoline or new aviation gasoline additive and the requirements of environmental agencies is recommended.  
1.6 The values stated in SI units are to be regarded as standard.  
1.6.1 Exception—Some industry standard methodologies uti...

  • Guide
    27 pages
    English language
    sale 15% off
  • Guide
    27 pages
    English language
    sale 15% off
ASTM
ASTM D3242-23(Test Method)
Standard Test Method for Acidity in Aviation Turbine Fuel

SIGNIFICANCE AND USE
5.1 Some acids can be present in aviation turbine fuels due either to the acid treatment during the refining process or to naturally occurring organic acids. Significant acid contamination is not likely to be present because of the many check tests made during the various stages of refining. However, trace amounts of acid can be present and are undesirable because of the consequent tendencies of the fuel to corrode metals that it contacts or to impair the water separation characteristics of the aviation turbine fuel.  
5.2 This test method is designed to measure the levels of acidity that can be present in aviation turbine fuel and is not suitable for determining significant acid contamination.
SCOPE
1.1 This test method covers the determination of the acidity in aviation turbine fuel in the range from 0.000 mg/g to 0.100 mg/g KOH.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D8252-23(Test Method)
Standard Test Method for Vanadium and Nickel in Crude and Residual Oil by X-ray Spectrometry

SIGNIFICANCE AND USE
5.1 This test method provides a rapid and precise elemental measurement with simple sample preparation. Typical analysis times are approximately 4 min to 5 min per sample with a preparation time of approximately 1 min to 3 min per sample.  
5.2 The quality of crude oil is related to the amount of sulfur present. Knowledge of the vanadium and nickel concentration is necessary for processing purposes as well as contractual agreements.  
5.3 The presence of vanadium and nickel presents significant risks for contamination of the cracking catalysts in the refining process.  
5.4 This test method provides a means of determining whether the vanadium and nickel content of crude meets the operational limits of the refinery and whether the metal content will have a deleterious effect on the refining process or when used as a fuel.
SCOPE
1.1 This test method covers the quantitative determination of total vanadium and nickel in crude and residual oil in the concentration ranges shown in Table 1 using X-ray fluorescence (XRF) spectrometry.  
1.2 Sulfur is measured for analytical purposes only for the compensation of X-ray absorption matrix effects affecting the vanadium and nickel X-rays. For measurement of sulfur by standard test method use Test Methods D4294, D2622 or other suitable standard test method for sulfur in crude and residual oils.  
1.3 This test method is limited to the use of X-ray fluorescence (XRF) spectrometers employing an X-ray tube for excitation in conjunction with wavelength dispersive detection system or energy dispersive high resolution semiconductor detector with the ability to separate signals of adjacent and near-adjacent elements.  
1.4 This test method uses inter-element correction factors calculated from XRF theory, the fundamental parameters (FP) approach, or best fit regression.  
1.5 Samples containing higher concentrations than shown in Table 1 must be diluted to bring the elemental concentration of the diluted material within the scope of this test method.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6.1 The preferred concentrations units are mg/kg for vanadium and nickel.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7754-23(Test Method)
Standard Test Method for Determination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional Gas Chromatography

SIGNIFICANCE AND USE
5.1 The analysis of trace oxygenates in automotive spark-ignition engine fuel has become routine in certain areas to ensure compliance whenever oxygenated fuels are used. In addition, test methods to measure trace levels of oxygenates in automotive spark-ignition fuel are necessary to assess product quality.
SCOPE
1.1 This test method covers the determination of trace oxygenates in automotive spark-ignition engine fuel. The method used is a multidimensional gas chromatographic method using 1,2-dimethoxy ethane as the internal standard. The oxygenates that are analyzed are: methyl-tertiary butyl ether (MTBE), ethyl-tertiary butyl ether (ETBE), diisopropyl ether (DIPE), methanol, tertiary-amyl methyl ether (TAME), n-propanol, i-propanol, n-butanol, i-butanol, tert-butyl alcohol, sec-butyl alcohol, and tert-pentanol. Ethanol is usually not measured as a trace oxygenate since ethanol can be used as the main oxygenate compound in finished automotive spark-ignition fuels such as reformulated automotive spark-ignition fuels. The concentration range of the oxygenates covered in the ILS study was from 10 mg/kg to 2000 mg/kg. In addition this method is also suitable for the measurement of the C5 isomeric alcohols (2-methyl-1-butanol, 2-methyl-2-butanol) present from the fermentation of ethanol.  
1.2 The ethanol blending concentration for which this test method applies ranges from 1 % to 15% by volume. Higher concentrations of ethanol coelute with methanol in the analytical column. Lower levels of ethanol, similar to the other oxygenate, can be calibrated and analyzed also. If higher ethanol concentrations are expected, the window cutting technique can be used to avoid ethanol from entering the analytical column and interfere with the determination of the other oxygenates of interest. Refer to Appendix X1 for details.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3.1 Alternative units, in common usage, are also provided to increase clarity and aid the users of this test method.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    18 pages
    English language
    sale 15% off
  • Standard
    18 pages
    English language
    sale 15% off
ASTM
ASTM D4808-23(Test Method)
Standard Test Methods for Hydrogen Content of Light Distillates, Middle Distillates, Gas Oils, and Residua by Low-Resolution Nuclear Magnetic Resonance Spectroscopy

SIGNIFICANCE AND USE
5.1 The hydrogen content represents a fundamental quality of a petroleum product that has been correlated with many of the performance characteristics of that product.  
5.2 This test method provides a simple and more precise alternative to existing test methods, specifically combustion techniques (Test Methods D5291) for determining the hydrogen content on a range of petroleum products.
SCOPE
1.1 These test methods cover the determination of the hydrogen content of petroleum products ranging from atmospheric distillates to vacuum residua using a continuous wave, low-resolution nuclear magnetic resonance spectrometer. (Test Method D3701 is the preferred method for determining the hydrogen content of aviation turbine fuels using nuclear magnetic resonance spectroscopy.)  
1.2 Three test methods are included here that account for the special characteristics of different petroleum products and apply to the following distillation ranges:    
Test Method  
Petroleum Products  
Boiling Range, °C (°F)
(approximate)  
A  
Light Distillates  
15–260 (60–500)  
B  
Middle Distillates  
200–370 (400–700)  
Gas Oils  
370–510 (700–950)  
C  
Residua  
510+ (950+ )  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. The preferred units are mass %.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Sections 7.2 and 7.4.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5188-23(Test Method)
Standard Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber and Piston Based Method)

SIGNIFICANCE AND USE
5.1 The tendency of a fuel to vaporize in automotive engine fuel systems is indicated by the vapor-liquid ratio of the fuel.  
5.2 Automotive fuel specifications generally include
T(V/L = 20) limits to ensure products of suitable volatility performance. For high ambient temperatures, a fuel with a high value of T(V/L = 20), indicating a fuel with a low tendency to vaporize, is generally specified; conversely for low ambient temperatures, a fuel with a low value of T(V/L = 20) is specified.
SCOPE
1.1 This test method covers the determination of the temperature at which the vapor formed from a selected volume of volatile petroleum product saturated with air at 0 °C to 1 °C (32 °F to 34 °F) produces a pressure of 101.3 kPa (one atmosphere) against vacuum. This test method is applicable to samples for which the determined temperature is between 36 °C and 80 °C (97 °F and 176 °F) and the vapor-liquid ratio is between 8 to 1 and 75 to 1.
Note 1: When the vapor-liquid ratio is 20:1, the result is intended to be comparable to the results determined by Test Method D2533.
Note 2: This test method may also be applicable at pressures other than one atmosphere, but the stated precision may not apply.  
1.2 This test method is applicable to both gasoline and gasoline-oxygenate blends.  
1.2.1 Some gasoline-oxygenate blends may show a haze when cooled to 0 °C to 1 °C. If a haze is observed in 12.5, it shall be indicated in the reporting of results. The precision and bias statements for hazy samples have not been determined (see Note 12).  
1.3 The values stated in SI units are to be regarded as standard.  
1.3.1 Exception—The values given in parentheses are provided for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warnings, see Section 7 and subsection 8.1.1.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5001-23(Test Method)
Standard Test Method for Measurement of Lubricity of Aviation Turbine Fuels by the Ball-on-Cylinder Lubricity Evaluator (BOCLE)

SIGNIFICANCE AND USE
5.1 Wear due to excessive friction resulting in shortened life of engine components such as fuel pumps and fuel controls has sometimes been ascribed to lack of lubricity in an aviation fuel.  
5.2 The relationship of test results to aviation fuel system component distress due to wear has been demonstrated for some fuel/hardware combinations where boundary lubrication is a factor in the operation of the component.  
5.3 The wear scar generated in the ball-on-cylinder lubricity evaluator (BOCLE) test is sensitive to contamination of the fluids and test materials, the presence of oxygen and water in the atmosphere, and the temperature of the test. Lubricity measurements are also sensitive to trace materials acquired during sampling and storage. Containers specified in Practice D4306 shall be used.  
5.4 The BOCLE test method may not directly reflect operating conditions of engine hardware. For example, some fuels that contain a high content of certain sulfur compounds can give anomalous test results.
SCOPE
1.1 This test method covers assessment of the wear aspects of the boundary lubrication properties of aviation turbine fuels on rubbing steel surfaces.  
1.1.1 This test method incorporates two procedures, one using a semi-automated instrument and the second a fully automated instrument. Either of the two instruments may be used to carry out the test.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D7398-23(Test Method)
Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography

SIGNIFICANCE AND USE
5.1 The boiling range distribution of FAMES provides an insight into the composition of product related to the transesterification process. This gas chromatographic determination of boiling range can be used to replace conventional distillation methods for product specification testing with the mutual agreement of interested parties.  
5.2 Biodiesel (FAMES) exhibits a boiling point rather than a distillation curve. The fatty acid chains in the raw oils and fats from which biodiesel is produced are mainly comprised of straight chain hydrocarbons with 16 to 18 carbons that have similar boiling temperatures. The atmospheric boiling point of biodiesel generally ranges from 330 °C to 357 °C. The Specification D6751 value of 360 °C max at 90 % off by Test Method D1160 was incorporated as a precaution to ensure the fuel has not been adulterated with high boiling contaminants.
SCOPE
1.1 This test method covers the determination of the boiling range distribution of fatty acid methyl esters (FAME). This test method is applicable to FAMES (biodiesel, B100) having an initial boiling point greater than 100 °C and a final boiling point less than 615 °C at atmospheric pressure as measured by this test method.  
1.2 The test method can also be applicable to blends of diesel and biodiesel (B1 through B100), however precision for these samples types has not been evaluated.  
1.3 The test method is not applicable for analysis of petroleum containing low molecular weight components (for example naphthas, reformates, gasolines, crude oils).  
1.4 Boiling range distributions obtained by this test method are not equivalent to results from low efficiency distillation such as those obtained with Test Method D86 or D1160, especially the initial and final boiling points.  
1.5 This test method uses the principles of simulated distillation methodology. See Test Methods D2887, D6352, and D7213.  
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM D7484-23a(Test Method)
Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine

SIGNIFICANCE AND USE
5.1 This test method was developed to assess the performance of a heavy-duty engine oil in controlling engine wear under operating conditions selected to accelerate soot production and valve-train wear in a turbocharged and aftercooled four-cycle diesel engine with sliding tappet followers equipped with exhaust gas recirculation hardware.  
5.2 The design of the engine used in this test method is representative of many, but not all, modern diesel engines. This factor, along with the accelerated operating conditions, shall be considered when extrapolating test results.
SCOPE
1.1 This test method, commonly referred to as the Cummins ISB Test, covers the utilization of a modern, 5.9 L, diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to valve-train wear.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exceptions—SI units are provided for all parameters except where there is no direct equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, or where there is a sole source of supply equipment specification.  
1.2.2 See also A7.1 for clarification; it does not supersede 1.2 and 1.2.1.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.  
1.4 Table of Contents:    
Section  
Scope  
1  
Referenced Documents  
2  
Terminology  
3  
Summary of Test Method  
4  
Significance and Use  
5  
Apparatus  
6  
Engine Fluids and Cleaning Solvents  
7  
Preparation of Apparatus  
8  
Engine/Stand Calibration and Non-Reference Oil Tests  
9  
Test Procedure  
10  
Calculations, Ratings, and Test Validity  
11  
Report  
12  
Precision and Bias  
13  
Annexes  
Safety Precautions  
Annex A1  
Intake Air Aftercooler  
Annex A2  
The Cummins ISB Engine Build Parts Kit  
Annex A3  
Sensor Locations and Special Hardware  
Annex A4  
External Oil System  
Annex A5  
Cummins Service Publications  
Annex A6  
Specified Units and Formats  
Annex A7  
Oil Analyses  
Annex A8  
Alternate Fuel Approval Process  
Annex A9  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    29 pages
    English language
    sale 15% off
  • Standard
    29 pages
    English language
    sale 15% off