ASTM E2239-24
(Practice)Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities
Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities
SIGNIFICANCE AND USE
4.1 This practice is intended to help reduce risks associated with lead hazards in buildings by providing standardized requirements for preserving records, findings, and recommendations associated with lead hazard activities.
4.2 This practice is intended for use by individuals and organizations that develop and have need to preserve objective evidence when contracting for or when conducting lead hazard activities themselves.
4.2.1 This practice is intended to assist in complying with management system requirements for record keeping promulgated by authorities having jurisdiction regarding conduct of lead hazard activities.
SCOPE
1.1 This practice describes requirements for preservation of records generated during lead hazard activities.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E2239 − 24
Standard Practice for
Record Keeping and Record Preservation for Lead Hazard
1
Activities
This standard is issued under the fixed designation E2239; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Terminology
1.1 This practice describes requirements for preservation of 3.1 Definitions:
records generated during lead hazard activities. 3.1.1 For definitions of terms not appearing here, refer to
Terminologies D1356 and E1605.
1.2 This standard does not purport to address all of the
3.2 Definitions of Terms Specific to This Standard:
safety concerns, if any, associated with its use. It is the
3.2.1 competence, n—
responsibility of the user of this standard to establish appro-
(1) demonstrated ability to apply knowledge and skills.
priate safety, health, and environmental practices and deter-
(2) specifically as applied to auditors, demonstrated per-
mine the applicability of regulatory limitations prior to use.
sonal attributes and demonstrated ability to apply knowledge
1.3 This international standard was developed in accor-
and skills. ISO 9000:2005 (3.1.6),
dance with internationally recognized principles on standard-
ISO 9000:2005 (3.9.14)
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- 3.2.2 conformity, n—fulfillment of a requirement.
mendations issued by the World Trade Organization Technical ISO 9000:2005 (3.6.1)
Barriers to Trade (TBT) Committee.
3.2.3 inspection, n—examination of a product design,
product, process, or installation and determination of its
2. Referenced Documents
conformity with specific requirements or, on the basis of
2
professional judgement, with general requirements.
2.1 ASTM Standards:
ISO 17000:2004
D1356 Terminology Relating to Sampling and Analysis of
Atmospheres
3.2.4 nonconformity, n—non-fulfillment of a requirement.
D4840 Guide for Sample Chain-of-Custody Procedures
ISO 9000:2005 (3.1.2)
E1605 Terminology Relating to Lead in Buildings
3.2.5 observation, n—a judgment that is based on what one
3
2.2 ISO Standards:
sees while conducting lead hazard activities and that is
ISO 9000-3 Quality Management and Quality Assurance
substantiated by objective evidence.
Standards—Part 3: Guidelines for the Application of ISO
3.2.6 objective evidence, n—data supporting the existence
9001:1994 to the Development, Supply, Installation and
or verity of something. ISO 9000:2005 (3.8.1)
Maintenance of Computer Software
3.2.6.1 Discussion—Objective evidence may be obtained
ISO 9000:2005 Quality Management Systems—
through observation, measurement, test, or other means.
Fundamentals and Vocabulary
3.2.7 procedure, n—specified way to carry out an activity or
ISO 17000:2004 Conformity Assessment—General Vocabu-
process. ISO 9000:2005 (3.4.5)
lary and Principles
3.2.7.1 Discussion—In many cases, procedures are docu-
mented (for example, quality system procedures). When a
procedure is documented, the term “written procedure” or
1
This practice is under the jurisdiction of ASTM Committee D22 on Air Quality
“documented procedure” is frequently used. A written or
and is the direct responsibility of Subcommittee D22.12 on Sampling and Analysis
documented procedure usually contains the purposes and scope
of Lead for Exposure and Risk Assessment.
Current edition approved March 1, 2024. Published March 2024. Originally
of an activity; what shall be done and by whom; when, where
approved in 2002. Last previous edition approved in 2020 as E2239 – 20. DOI:
and how it shall be done; what materials, equipment and how
10.1520/E2239-24.
documents shall be used; and how it shall be controlled and
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
recorded.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
3.2.8 record, n—a document stating results achieved or
the ASTM website.
3
providing evidence of activities performed.
Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036, http://www.ansi.org. ISO 9000:2005 (3.7.6)
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E2239 − 24
3.2.9 requirement, n—need or expectation that is stated, 5.3.2.1 Data forms, either
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2239 − 20 E2239 − 24
Standard Practice for
Record Keeping and Record Preservation for Lead Hazard
1
Activities
This standard is issued under the fixed designation E2239; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice describes requirements for preservation of records generated during lead hazard activities.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1356 Terminology Relating to Sampling and Analysis of Atmospheres
D4840 Guide for Sample Chain-of-Custody Procedures
E1605 Terminology Relating to Lead in Buildings
3
2.2 ISO Standards:
ISO 9000-3 Quality Management and Quality Assurance Standards—Part 3: Guidelines for the Application of ISO 9001:1994
to the Development, Supply, Installation and Maintenance of Computer Software
ISO 9000:2005 Quality Management Systems—Fundamentals and Vocabulary
ISO 17000:2004 Conformity Assessment—General Vocabulary and Principles
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms not appearing here, refer to Terminologies D1356 and E1605.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 competence, n—(1) demonstrated ability to apply knowledge and skills.
(1) demonstrated ability to apply knowledge and skills.
1
This practice is under the jurisdiction of ASTM Committee D22 on Air Quality and is the direct responsibility of Subcommittee D22.12 on Sampling and Analysis of
Lead for Exposure and Risk Assessment.
Current edition approved Sept. 1, 2020March 1, 2024. Published September 2020March 2024. Originally approved in 2002. Last previous edition approved in 20162020
as E2239 – 12 (2016). DOI: 10.1520/E2239-20.20. DOI: 10.1520/E2239-24.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E2239 − 24
(2) specifically as applied to auditors, demonstrated personal attributes and demonstrated ability to apply knowledge and skills.
ISO 9000:2005 (3.1.6)
(2) specifically as applied to auditors, demonstrated personal attributes and demonstrated ability to apply knowledge and skills.
ISO 9000:2005 (3.1.6),
ISO 9000:2005 (3.9.14)
3.2.2 conformity, n—fulfillment of a requirement.
ISO 9000:2005 (3.6.1)
3.2.3 inspection, n—examination of a product design, product, process, or installation and determination of its conformity with
specific requirements or, on the basis of professional judgement, with general requirements.
ISO 17000:2004
3.2.4 nonconformity, n—non-fulfillment of a requirement. ISO 9000:2005 (3.1.2)
3.2.5 observation, n—a judgment that is based on what one sees while conducting lead hazard activities and that is substantiated
by objective evidence.
3.2.6 objective evidence, n—data supporting the existence or verity of something. ISO 9000:2005 (3.8.1)
3.2.6.1 Discussion—
Objective evidence may be obtained through observation, measurement, test, or other means.
3.2.7 procedure, n—specified way to carry out an activity or process. ISO 9000:2005 (3.4.5)
3.2.7.1 Discussion—
In many cases, procedures are documented (for example, quality system procedures). When a procedure is documented, the term
“written procedure” or “documented procedure” is frequently used. A written or documented procedure usually contains the
purposes and scope of an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.