ASTM A1049/A1049M-10
(Specification)Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for Pressure Vessels and Related Components
Standard Specification for Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for Pressure Vessels and Related Components
ABSTRACT
This specification covers ferritic/austenitic (duplex) stainless steel forgings for boilers, pressure vessels, and associated equipment. The steels shall be manufactured using melting and forging processes. Forgings may be machined before solution annealing. The forgings shall undergo tension and hardness tests. Also, they shall be subjected to a non-destructive examination by ultrasonic inspection.
SCOPE
1.1 This specification covers ferritic/austenitic (duplex) stainless steel forgings for boilers, pressure vessels, and associated equipment in grades that are also found in Specification A182/A182M.
1.2 The purchaser may specify in the order or contract any appropriate supplementary requirements that are provided in Specification A788/A788M.
1.3 Unless the order specifies the applicable “M” specification designation the material shall be furnished to the inch-pound units.
1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standard. Within the text and tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A1049/A1049M −10
StandardSpecification for
Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for
1
Pressure Vessels and Related Components
This standard is issued under the fixed designation A1049/A1049M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* A923 Test Methods for Detecting Detrimental Intermetallic
Phase in Duplex Austenitic/Ferritic Stainless Steels
1.1 This specification covers ferritic/austenitic (duplex)
E165 Practice for Liquid Penetrant Examination for General
stainless steel forgings for boilers, pressure vessels, and asso-
Industry
ciated equipment in grades that are also found in Specification
G48 Test Methods for Pitting and Crevice Corrosion Resis-
A182/A182M.
tance of Stainless Steels and Related Alloys by Use of
1.2 The purchaser may specify in the order or contract any
Ferric Chloride Solution
appropriate supplementary requirements that are provided in
2.2 Other Standards:
Specification A788/A788M.
3
ASME Boiler and Pressure Vessel Code
1.3 Unless the order specifies the applicable “M” specifica-
NACE MR0175/ISO15156 Petroleum and Natural Gas
tion designation the material shall be furnished to the inch-
Industries—Materials for Use in H S—Containing Envi-
2
4
pound units.
ronments in Oil and Gas Production
1.4 The values stated in either inch-pound or SI (metric)
3. Ordering Information and General Requirements
units are to be regarded separately as standard. Within the text
andtables,theSIunitsareshowninbrackets.Thevaluesstated
3.1 Material supplied to this specification shall conform to
in each system may not be exact equivalents; therefore, each
the requirements of Specification A788/A788M, which out-
system shall be used independently of the other. Combining
lines additional ordering information, manufacturing
values from the two systems may result in nonconformance
requirements, testing and retesting methods and procedures,
with the specification.
marking, certification, product analysis variations, and addi-
tional supplementary requirements.
2. Referenced Documents
3.1.1 If the requirements of this specification are in conflict
2
2.1 ASTM Standards:
with the requirements of Specification A788/A788M, the
A182/A182M Specification for Forged or Rolled Alloy and
requirements of this specification shall prevail.
Stainless Steel Pipe Flanges, Forged Fittings, and Valves
3.1.2 The purchaser may require that the forging be ma-
and Parts for High-Temperature Service
chined to an approved heat treatment drawing indicating the
A370 Test Methods and Definitions for Mechanical Testing
proposed configuration of the forging at the time of the
of Steel Products
specified solution heat treatment.
A388/A388M Practice for Ultrasonic Examination of Steel
3.1.3 The purchaser may approve the use of an alternate
Forgings
liquid quenching medium for cooling from the solution treat-
A745/A745M Practice for Ultrasonic Examination of Aus-
ment temperature.
tenitic Steel Forgings
3.2 The purchaser shall specify the acceptance criteria for
A788/A788M Specification for Steel Forgings, General Re-
eitherMethodsBorCofTestMethodsA923,ifsupplementary
quirements
requirement S1 is selected.
3.3 The purchaser shall specify the required minimum
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
pitting resistance equivalent number (PREN) value determined
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
according to the applicable equation in Table 1.
A01.06 on Steel Forgings and Billets.
Current edition approved Nov. 1, 2010. Published December 2010. Originally
approved in 2006. Last previous edition approved in 2006 as A1049/A1049M – 06.
DOI: 10.1520/A1049_A1049M-10.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Society of Mechanical Engineers (ASME), ASME
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM International Headquarters, Three Park Ave., New York, NY 10016-5990.
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Association of Corrosion Engineers (NACE), 1440
the ASTM website. South Creek Dr., Houston, TX 77084-4906.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A1049/A1049M−10
TABLE 1 Chemical Requirements
A A A A B B B A A A
Grade F50 F51 F52 F53 F54 F55 F57 F59 F60 F61
A A A A B B B A A A
UNS No.
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A1049/A1049M–06 Designation: A1049/A1049M – 10
Standard Specification for
Stainless Steel Forgings, Ferritic/Austenitic (Duplex), for
1
Pressure Vessels and Related Components
This standard is issued under the fixed designation A1049/A1049M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers ferritic/austenitic (duplex) stainless steel forgings for boilers, pressure vessels, and associated
equipment in grades that are also found in Specification A182/A182M.
1.2 The purchaser may specify in the order or contract any appropriate supplementary requirements that are provided in
Specification A788/A788M.
1.3 Unless the order specifies the applicable “M” specification designation the material shall be furnished to the inch-pound
units.
1.4 The values stated in either inch-pound or SI (metric) units are to be regarded separately as standard. Within the text and
tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system
shall be used independently of the other. Combining values from the two systems may result in nonconformance with the
specification.
2. Referenced Documents
2
2.1 ASTM Standards:
A182/A182M Specification for Forged or RolledAlloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts
for High-Temperature Service
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A388/A388M Practice for Ultrasonic Examination of Steel Forgings
A745/A745M Practice for Ultrasonic Examination of Austenitic Steel Forgings
A788/A788M Specification for Steel Forgings, General Requirements
A923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
E165 Practice for Liquid Penetrant Examination for General Industry
G48 TestMethodsforPittingandCreviceCorrosionResistanceofStainlessSteelsandRelatedAlloysbyUseofFerricChloride
Solution
2.2 Other Standards:
3
ASME Boiler and Pressure Vessel Code
NACE MR0175/ISO15156 Petroleum and Natural Gas Industries—Materials for Use in H S—Containing Environments in Oil
2
4
and Gas Production
3. Ordering Information and General Requirements
3.1 Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlines
additional ordering information, manufacturing requirements, testing and retesting methods and procedures, marking, certification,
product analysis variations, and additional supplementary requirements.
3.1.1 If the requirements of this specification are in conflict with the requirements of Specification A788/A788M, the
requirements of this specification shall prevail.
3.1.2 The purchaser may require that the forging be machined to an approved heat treatment drawing indicating the proposed
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.06
on Steel Forgings and Billets.
Current edition approved Sept. 1, 2006. Published September 2006. DOI: 10.1520/A1049_A1049M-06.
Current edition approved Nov. 1, 2010. Published December 2010. Originally approved in 2006. Last previous edition approved in 2006 as A1049/A1049M – 06. DOI:
10.1520/A1049_A1049M-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. ForAnnualBookofASTMStandards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990.
4
Available from National Association of Corrosion Engineers (NACE), 1440 South Creek Dr., Houston, TX 77084-4906.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A1049/A1049M – 10
configuration of the forging at the time of the specified solution heat treatment.
3.1.3 The purchaser may approve the use of an alternate liquid quenching medium for cooling from the solution treatment
temperature.
3.2 The purchaser shall specify the acceptance criteria fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.